Protecting The Environment - DeWalt DCE560 Manual

7. Press and hold plunger rod release trigger
the plunger rod handle
against the tube.
8. Release the plunger rod release trigger.
9. Rotate cartridge holder to desired angle.
Sausage Holder (Fig. A, H, I)
1. Ensure that plunger used is appropriate to material.
nOTE: Using incorrect plunger may result in material
container exploding during use, damaging cartridge holder
and/or caulk gun.
2. Unscrew and remove nozzle cap
3. Press and hold plunger rod release trigger
plunger rod handle 4 , pull plunger rod
caulk/material casing to fit inside the sausage holder
4. Insert sausage pack into sausage holder and cut casing
(closest end to the nozzle) according to material
manufacturer's instructions.
iMPORTAnT: DO nOT remove caulk/material material
from the casing. nEVER dip the nozzle tip into any type
of material.
5. With nozzle tip facing away from tool, screw nozzle cap
back onto sausage holder.
6. Trim tip of nozzle for appropriate application (Fig. I).
nOTE: Material left in the cartridge/sausage holder may dry if
left unattended. Follow manufacturer's recommendations when
using caulk or adhesive material.
MAINTENANCE
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
The charger and battery pack are not serviceable.
Lubrication
Your power tool requires no additional lubrication.
Cleaning (Fig. A)

WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
6 while pushing
forward until the plunger
4
13 . and nozzle.
6 . Using the
5 back to allow the
Never let any liquid get inside the tool; never immerse any
is
7 part of the tool into a liquid.
NOTICE: Material left in the cartridge/sausage holder may
dry if left unattended. Do not attempt to dispense material
under this condition. Follow the adhesive manufacturer's
recommendations when using caulk or adhesive material
to reduce the risk of property damage.
To clean the cartridge holder, follow adhesive manufacturer's
recommendations for cleaning material from nozzle, barrel
plunger and plunger rod.
To clean the sausage holder, unscrew nozzle cap
sausage holder
manufacturer's recommendations for cleaning material from
nozzle, barrel plunger, plunger rod and sausage holder, along
.
12
with any instructions provided on accessory component labels
and documents.
Optional Accessories

WARNING: Since accessories, other than those offered
by D WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.

Protecting the Environment

Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails
to produce sufficient power on jobs which were easily done
before. At the end of its technical life, discard it with due care for
our environment:
• Run the battery pack down completely, then remove it from
the tool.
• Li-Ion cells are recyclable. Take them to your dealer or a
local recycling station. The collected battery packs will be
recycled or disposed of properly.
12 and remove from tool. Follow the adhesive
WALT recommended
e
English
13 and
11