Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for HardWire SC-2
-
Page 2: Declaration Of Conformity
Directive. Roger Johnsen Vice-President of Engineering 8760 S. Sandy Parkway Sandy, Utah 84070, USA Date: October 4, 2010 European Contact: Your local HardWire Sales and Service Office or ® Harman Music Group 8760 South Sandy Parkway Sandy, Utah 84070 USA... -
Page 3: Electromagnetic Compatibility
Warning If you want to dispose of this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery, and recycling. For your protection, read the following: Private households in the 25 member states of the EU, in Switzerland and Norway may return their used electronic product free of charge to designated collection facilities or to a retailer (if you Important Safety Instructions... -
Page 4: Warranty
The foregoing is in lieu of all other warranties, expressed or implied, and HardWire neither assumes nor authorizes any person to assume any obligation or liability in connection with the sale of this product. In no event shall HardWire or its dealers be liable for special or consequential damages or from any delay in the performance of this warranty due to causes beyond their control. -
Page 5: Included Items
® significant improvements in effects pedals for guitar. HardWire pedals pro- vide a suite of well-known effects, each with superior tone and control. But these pedals go above and beyond their peers to provide such distinguishing... - Page 7 What Does This Do? 1. Level Knob - Controls the distortion output level. Turn the knob clockwise to increase and counter-clockwise to decrease the output level. 2. DC Adapter Jack - Connect (an optional) Harman PS200R power supply to this jack. Use the proper supply for your area’s mains line voltage.
- Page 8 6. Voicing Switch - This switches between the Distortion’s two voicings. Crunch provides a classic balanced distortion. Saturated features an extra gain stage for maximum sustain distortion making it ideal for solos. 7. Input - Connect your instrument or the output of another pedal to this jack.
- Page 9 10. Foot Switch - Turns the effect on and off. 11. Output - Connect this output to the input of your amplifier or the input of another pedal. Note: Use unbalanced mono instrument cables only.
-
Page 10: Amplifier Setup
Amplifier Setup PS200R (optional) -
Page 11: Battery Operation
Battery Operation In the event that battery power is completely depleted, HardWire pedals automatically switch into bypass. This eliminates the need to remove the pedal from your pedal chain if the battery is dead. To replace the battery, do the following: Using the tip of a 1/4”... - Page 12 Switch is properly fastened, both Release Pins are flush with the outer side of the pedal. Foot Switch Pedal Switch 9VDC Battery Foot Switch Release Pin Battery Compartment Foot Switch Spring Release Pin Pedal Chassis...
- Page 13 HardWire Performance Accessories The performance accessories make integrating a HardWire pedal into any pedal board a snap. The following accessories are included: • Hook-and-loop Pedalboard Pad (designed to attach to the surfaces found on most commercial pedalboards) • Foot Switch Glow Sticker (easily visible on dark stages) •...
- Page 14 Hook-and-loop Pedalboard Pad To attach the Pedalboard Pad, do the following: Peel off the existing rubber skid pad from the bottom of the pedal. Peel the adhesive protector from the back of the Pedalboard Pad. Apply the Pedalboard Pad to the bottom of the pedal.
- Page 15 Foot Switch Glow Sticker To attach the Foot Switch Glow Sticker, do the following: Peel the adhesive backing from the Foot Switch Glow Sticker. Apply the Glow Sticker to the top of the Foot Switch.
- Page 16 StompLock To place the StompLock over the pedal knobs, do the following: Set the knobs to your preferred setting. Gently push the StompLock over the top of the knobs. To remove the StompLock, gently lift one side and then the other.
-
Page 17: Specifications
>500 kΩ - effect on Output Impedance: 1 kΩ - effect on Input Impedance: True hardwire bypass - effect off Output Impedance: True hardwire bypass - effect off Power Supply: 9V Alkaline Dry Battery or Harman PS200R 9V DC power... - Page 20 PH (801) 566-8800 FAX (801) 566-7005 ® HardWire is a registered trademark of Harman Designed in the USA Copyright - Harman Printed in China ® HardWire SC-2 Owners Manual 18-0666V-B Please visit us on the World Wide Web at: www.hardwirepedals.com...