一、 Features Factory model(reference only) L47A18 HAC model HL47E Options Functions Screen size (inches) General Display type Aspect ratio 16:9 Resolution 1920*1080 Brightness 550 cm/2 Contrast 800:1 Response time(ms) Video Display Capabilities 480i/480P/720P/1080i/1080P Viewing Angle H:178/V:178 Color display 16.7million Active Matrix TFT...
Multilingual Display E/F/S Auto Channel Programming Channel Caption Channel Label Channel Skip/Add Favorite Channel Program Guide Access(TV guide) Clock Programmable Timer Sleep Timer Alarm (Auto timer on/off) Picture-In-Picture Freeze Picture Remote Control HTR-282E (Universal) ATSC/NTSC Tuner HDMI Input Component Video Input Composite Video Input S-Video Input RF Input...
六、Bus Control Adjustment 1）Factory Mode Using the romote controller to enter into Factory Menu. Press Menu to call main menu displaying on the screen. And then press “8”,“ 8”,“9”,“3”,“OK” in turn.You will see the screen displaying as following.You can check the version of the software,adjust some settings.But we don’t advise you change this settings.because of the TV has already hold in the state of optimality.If you have to chang this settings,please connect with the local service center.
2.Image Version, Atmega Version Image Version: This is the current software version. Atmega Version: The serial number, it is recorded for this board...
3.OK MENU EXIT OK: press OK to submenu MENU: return to upper menu EXIT: Press “EXIT” of the romote controller to exit from factory menu...
4. Operate in Factory Menu There are 5 items in the root Product Mode, Aging Mode, Shop End, Service Mode, Design Mode. 1) Product Mode includes 3 items, White Balance Setting, Back Light Set to Factory Default Value.Do not change the value commonly.
2)Aging Mode This is for factory run-in testing.
3) Shop End is for debuging, and do not change anything commonly.
4)Service Mode is for debugging, and do not change anything commonly.
5) Design Mode includes 4 items, Video Setting, Audio Setting, Screen Setting, Others...
a. Video Setting includes 4 items, Threshold, Picture Mode, ADC Auto Adjust, Gray Step. Threshold allows you to change the adjustable range of brightness, contrast, chroma, hue and sharpness. Picture Mode allows you to change the state of picture mode, such as Vivid mode, Standard mode and Mild mode. ADC Auto Adjust and Gray Step are for debugging, and do not change anything.
b. Audio Setting includes 4 items, Sound Effect, Sound Mode, Sound Curve, Headphone Sound curve. All these items are for debugging,and do not change anything commonly.
c. Screen Setting allows you to change V-SIZE, V-POSITION, H-SIZE, H-POSITION of the screen displaying. Normally you need not to change anything.
d. Others including 2 items, Audio Output and Set E2prom to default. Audio Output allows you to change the volume of Audio Output. Set E2prom to default will Clear all changing you have made to the TV set’s software setting, such as Channel list you have tuned, volume, brightness, and etc. and initialize TV set’s software to the state like a new TV set buyed right now.
Connection Options Left side connetions Antenna Input Connect cable or antenna signals to the TV, either directly or through your cable box. HDMI2 connect a signal to HDMI/DVI. PC VIDEO Input Connect the monitor output connector from a PC to the jack DVD/DTV Input (Component ) Connect a component...
Introduction Remote Controller - The remote controller cannot be operated unless the batteries are properly loaded. - When using the remote control, aim it at the remote control sensor on the TV. Function introduction TV USB Press the SELECT button repeatedly to select one of the system modes in which the remote control can be used.
VDAC_AVDD33 needs to be very clean. If you use switching supplies, consider using a small linear regulator for this supply. (250 mA worst case) Route VDAC_AVDD33 as a wide trace or fill area on the top layer of the PCB all the way to the connector (14) VDAC_AVDD3P3 L118...
Connect PCI_VIO to 5V if any BCM3560 PCI or other digital pin is connected or pulled to a 5V source; D3.3V_BCM3560 D5.0V D3.3V otherwise connect PCI_VIO to 3.3V. 0_NC 0_NC C216 C216 0.1uF 0.1uF C224 C224 0.1uF 0.1uF (10,17) EBI_ADDR14 U22H U22H R107...
U22C U22C BCM3551KPB5G BCM3551KPB5G BGA676_35X35 BGA676_35X35 RN33 RN33 BCM_DDR_ADDR0 BCM_DDR_WEb MEM_DDR_WEb C100 C100 100uF 100uF DDR0_ADDR00 BCM_DDR_ADDR1 BCM_DDR_CASb MEM_DDR_CASb Try to place decoupling capacitors on the D2.6V_BCM3560 DDR0_ADDR01 BCM_DDR_ADDR2 BCM_DDR_RASb MEM_DDR_RASb C319 C319 0.1uF 0.1uF same side of the PCB as the DDR to reduce DDR0_ADDR02 BCM_DDR_ADDR3 BCM_DDR_CS0b...