Page 1 ® ErisTerminal SIP Deskset VSP715 Administrator and Provisioning Manual Rev. 1 07/15...
Page 2: Table Of Contents
VSP715 Administrator and Provisioning Manual ONTENTS Preface ...................... 6 Text Conventions ........................ 7 Audience..........................7 Related Documents ......................7 Introducing the VSP715 ................8 About the VSP715 deskset....................9 Quick Reference Guide ....................10 Programmable Keys ......................11 Other possible programmable key settings ............11 LED Behavior ........................13 Network Requirements .....................
Page 3 VSP715 Administrator and Provisioning Manual System Status...................... 35 System Pages ........................36 SIP Account Management ................... 36 General Account Settings ................36 Dial Plan......................38 SIP Server Settings ..................39 Registration Settings ..................39 Outbound Proxy Settings ................39 Backup Outbound Proxy Settings ..............40 Audio Settings ....................
Page 4 VSP715 Administrator and Provisioning Manual LDAP ........................67 LDAP Settings....................67 Broadsoft ......................70 Broadsoft Phonebook Settings..............70 Call History ......................71 Servicing Pages........................72 Reboot ......................... 72 Time and Date ..................... 72 Time and Date Format .................. 73 Network Time Settings .................. 73 Time Zone and Daylight Savings Settings ............73 Manual Time Settings..................
Page 5 VSP715 Administrator and Provisioning Manual General configuration file settings ..............108 MAC-specific configuration file settings ............. 110 "provisioning" Module: Provisioning Settings..............112 "time_date" Module: Time and Date Settings ..............115 "log" Module: Log Settings....................119 "remoteDir" Module: Remote Directory Settings.............120 "web" Module: Web Settings ..................125 "user_pref"...
Page 6: Preface
Purchase date: _______________________________ Place of purchase: ____________________________ Both the model and serial numbers of your VTech product can be found on the bottom of the console. Save your sales receipt and original packaging in case it is necessary to return your telephone for warranty service.
Page 7: Text Conventions
NAT traversal settings, and so on. As the VSP715 SIP deskset becomes certified for IP PBX equipment or services, VTech may publish interop guides for those specific services. The interop guides will recommend second-party devices and settings, along with VSP715-specific configurations for optimal performance with those services.
Page 8: Introducing The Vsp715
VSP715 Administrator and Provisioning Manual H A P T E R VSP715 NTRODUCING THE This administrator and provisioning guide contains detailed instructions for configuring the VSP715 SIP deskset. Please read this guide before attempting to configure the VSP715. Some of the configuration tasks described in this chapter are duplicated in the Web User Interface (WebUI) described in the next chapter, but if you need to assign static IP addresses, they must be set at each device.
Page 9: About The Vsp715 Deskset
VSP715 Administrator and Provisioning Manual About the VSP715 deskset The VTech VSP715 SIP deskset is a business phone designed to work with popular SIP telephone (IP PBX) equipment and services. Once you have ordered and configured your SIP equipment or service, the VSP715 enables you to make and receive calls as you would with any other business phone.
Page 10: Quick Reference Guide
VSP715 Administrator and Provisioning Manual Quick Reference Guide The controls you will need to use to configure the VSP715 manually are described below. SOFT KEYS Perform the actions indicated by the on-screen labels. Programmable keys Can be programmed to perform functions or access features.
Page 11: Programmable Keys
VSP715 Administrator and Provisioning Manual Programmable Keys The table below lists the default settings for the programmable feature keys (PFKs). The key assignments on your phone may be different. Some keys may be programmed as Quick Dial keys, for example. You can assign functions to programmable keys using the phone menu (Main Menu >...
Page 12 VSP715 Administrator and Provisioning Manual  Park Call—Dials the access code to park your current call. To program access codes, see “SIP Account Management” on page  Retrieve Parked Call—Dials the access code to retrieve a parked call.  In Call DTMF—Dials a string of numbers while you are on a call. For example, pressing the key might dial a conference access code.
Page 13: Led Behavior
VSP715 Administrator and Provisioning Manual LED Behavior The programmable keys have LEDs that indicate various states. Table 3. VSP715 LED behavior Key function LED Activity Description Account Flashing ORANGE Account not registered Steady GREEN Dialing or on a call Quickly flashing GREEN Ringing incoming call Slowly flashing GREEN Held call...
Page 14: Network Requirements
VSP715 Administrator and Provisioning Manual Network Requirements A simple VSP715 SIP deskset installation example is shown in Figure 1. A switched network topology is recommended for your LAN (using standard 10/100 Ethernet switches that carry traffic at a nominal rate of 100 Mbit/s). The office LAN infrastructure should use Cat.-5/Cat.-5e cable.
Page 15: Vsp715 Configuration Methods
VSP715 Administrator and Provisioning Manual VSP715 Configuration Methods You can configure the VSP715 using one of the following methods:  From the VSP715 itself, using the menus. The VSP715 menus are best suited to configuring a few settings, perhaps after the initial setup has been done. For administrators, the settings available on the VSP715 menus include network settings, account settings, and provisioning settings.
Page 16: Adding A Custom Logo
“Uploading a custom logo” on page 16. The default logo for bootup and idle mode is the vtech logo. Idle screen logo behavior The behavior described below is disabled by default. You can enable the logo to appear instead of the idle screen after a specified period of inactivity.
Page 17: Custom Logo User Interactions
VSP715 Administrator and Provisioning Manual  image is not in black and white Custom logo user interactions For VSP715 users, pressing any hard key will exit the idle logo and perform the key's function. For example, pressing MENU will show the Main Menu. Pressing a soft key when the idle logo is showing will switch to the idle screen.
Page 18: Customizing Soft Keys
VSP715 Administrator and Provisioning Manual Customizing Soft Keys The configuration file allows you to select which soft keys can appear on the Idle screen, the Active Call screen, the Held Call screen and the Live Dial screen. You can also specify the position of each soft key.
Page 19 VSP715 Administrator and Provisioning Manual Table 4. Custom Soft Keys Screen Available Soft Keys Soft Key Text Line (visible with more than one account assigned) Line Settings Settings Call Active Blank Park Call Park Hold Hold Transfer Transfer Conference Conf XferLine (visible with more than one call) XferCall ConfLine (visible with more than one call)
Page 20 VSP715 Administrator and Provisioning Manual Table 4. Custom Soft Keys Screen Available Soft Keys Soft Key Text Live Dial Blank Directory Directory Call Log Call Log Redial Redial Messages Message Dial Dial Input (letter/number selection) Cancel Cancel Backspc Backspc The custom soft keys parameters are included in the "softkey" module. For more information, see “"softkey"...
Page 21: Configuration Using The Phone Menus
VSP715 Administrator and Provisioning Manual H A P T E R ONFIGURATION SING THE HONE ENUS The VSP715 Main Menu has the following sub-menus:  Features—manage calls, view and add directory entries, view call history, access messages, and use the speed dial menu. ...
Page 22: Viewing The Main Menu
VSP715 Administrator and Provisioning Manual Viewing the Main Menu To use the VSP715 menu: 1. When the VSP715 is idle, press MENU/SELECT. The Main Menu appears.   2. Press to highlight the desired sub-menu, and then press MENU/SELECT.  You can also press a corresponding dial pad key to select a numbered menu item.
Page 23 VSP715 Administrator and Provisioning Manual Table 5. Status menu summary Menu Information listed 1. Network  IP address  DHCP status (Enabled/Disabled)  Subnet Mask  Gateway IP address  DNS server 1 IP address  DNS server 2 IP address ...
Page 24: Viewing Line Status
VSP715 Administrator and Provisioning Manual Viewing Line status To view line status, from the Status menu, select Line. The Line menu lists the available lines, along with icons indicating each line's current registration status. Table 6. Line status icons Icon Description Line registered Line unregistered...
Page 25: Using The Admin Settings Menu
VSP715 Administrator and Provisioning Manual Using the Admin Settings Menu To access the Admin Settings menu: 1. When the VSP715 is idle, press MENU/SELECT.  The Main Menu appears.   to highlight Admin settings, and then press MENU/SELECT. 2. Press -or- Press 4 (Admin settings) on the dial pad.
Page 26: Using The Network Setting Menu
VSP715 Administrator and Provisioning Manual Using the Network Setting menu Use the Network setting menu to configure network-related settings for the VSP715. For more information about these settings, see “Basic Network Settings” on page 58 “Advanced Network Settings” on page To use the Network setting menu: ...
Page 27 VSP715 Administrator and Provisioning Manual To set static IP for the VSP715:   1. From the Network setting menu, press to highlight Set static IP, and then press MENU/SELECT. If DHCP is disabled, the Set static IP menu appears. If DHCP is enabled, an error message appears briefly before returning you to the Network setting menu.
Page 28 VSP715 Administrator and Provisioning Manual 2. Enter the IP address for the primary DNS server. Use the dial pad and the Add dot soft   key to enter characters. Press to advance to the next character.  3. Press and enter the IP address for the secondary DNS server.
Page 29: Using The Line Menu
VSP715 Administrator and Provisioning Manual Using the Line menu Use the Line menu to configure line-specific settings for the phone. To use the Line setting menu:  1. From the Admin Settings menu, press to highlight Line, and then press SELECT.The Line menu appears.
Page 30: Using The Provisioning Menu
VSP715 Administrator and Provisioning Manual Using the Provisioning menu Use the Provisioning menu to manually configure auto-provisioning settings. For more information about auto-provisioning, see “Provisioning” on page 77 “Provisioning Using Configuration Files” on page On the Provisioning menu you can configure: ...
Page 31: Using The Webui
VSP715 Administrator and Provisioning Manual H A P T E R SING THE The WebUI allows you to configure all aspects of VSP715 deskset operation, including account settings, programmable keys, network settings, contact lists, and provisioning settings. The WebUI is embedded in the VSP715 operating system. When you access the WebUI, you are accessing it on the device, not on the Internet.
Page 32: Using The Web User Interface (Webui)
VSP715 Administrator and Provisioning Manual Using the Web User Interface (WebUI) The Web User Interface (WebUI) resides on the VSP715 deskset. You can access it using an Internet browser. After you log in to the WebUI, you can configure the VSP715 on the following pages: ...
Page 33 VSP715 Administrator and Provisioning Manual To access the WebUI: 1. Ensure that your computer is connected to the same network as the VSP715. Your computer may already be connected to the network through the PC port on the back of the VSP715.
Page 34: Saving Your Settings
VSP715 Administrator and Provisioning Manual Saving your settings Most WebUI configuration pages have a button. Click to save changes you have made on the page. During a configuration session, click before you move on to the next WebUI page. Back to Contents Using the WebUI...
Page 35: Status Page
VSP715 Administrator and Provisioning Manual Status Page The WebUI System Status page is equivalent to the Status menu on the VSP715. System Status The System Status page shows:  General information about your device, including model, MAC address, and firmware version ...
Page 36: System Pages
VSP715 Administrator and Provisioning Manual System Pages SIP Account Management On the SIP Account Management pages, you can configure each account you have ordered from your service provider. The SIP Account settings are also available as parameters in the configuration file. See “"sip_account"...
Page 37 VSP715 Administrator and Provisioning Manual Setting Description Authentication name If authentication is enabled on the server, enter the authentication name (or authentication ID) for authentication with the server. Authentication password If authentication is enabled on the server, enter the authentication password for authentication with the server. Dial Plan Enter the dial plan, with dialing strings separated by a | symbol.
Page 38: Dial Plan
VSP715 Administrator and Provisioning Manual Dial Plan The dial plan consists of a series of dialing rules, or strings, that determine whether what the user has dialed is valid and when the VSP715 should dial the number. Dialing rules must consist of the elements defined in the table below. Element Description Any dial pad key from 0 to 9, including # and *.
Page 39: Sip Server Settings
VSP715 Administrator and Provisioning Manual SIP Server Settings Setting Description Server address Enter the IP address or domain name for the SIP server. Server port Enter the port number that the SIP server will use. Registration Settings Setting Description Server address Enter the IP address or domain name for the registrar server.
Page 40: Backup Outbound Proxy Settings
VSP715 Administrator and Provisioning Manual Backup Outbound Proxy Settings Setting Description Server address Enter the IP address or domain name for the backup proxy server. Server port Enter the port number that the backup proxy server will use. Audio Settings Setting Description Ringer Tone...
Page 41: Quality Of Service
VSP715 Administrator and Provisioning Manual Quality of Service Setting Description DSCP (voice) Enter the Differentiated Services Code Point (DSCP) value from the Quality of Service setting on your router or switch. DSCP (signalling) Enter the Differentiated Services Code Point (DSCP) value from the Quality of Service setting on your router or switch.
Page 42: Feature Access Codes Settings
VSP715 Administrator and Provisioning Manual Feature Access Codes Settings If your IP PBX service provider uses feature access codes, then enter the applicable codes here. You can assign many of these features to programmable feature keys, which enables end users to press the keys to dial out the codes you enter here. To configure programmable feature keys, see “Programmable Keys”...
Page 43: Busy Lamp Field
VSP715 Administrator and Provisioning Manual Setting Description Assignable to PFK? Group Call Pickup Enter the Group Call Pickup code. Dialing the code enables the user to answer a call ringing at another VSP715 that is part of the same group. Direct Call Pickup Enter the Direct Call Pickup code.
Page 44: Voicemail Settings
VSP715 Administrator and Provisioning Manual Voicemail Settings Setting Description Enable MWI When enabled, the account subscribes to the "message Subscription summary" event package. The account may use the User ID or the service provider's "Mailbox ID". Mailbox ID Enter the URI for the mailbox ID. The phone uses this URI for the MWI subscription.
Page 45: Music On Hold Settings
VSP715 Administrator and Provisioning Manual Music on Hold Settings Setting Description Enable Local MoH Enables or disables a hold-reminder tone that the user hears when a far-end caller puts the call on hold. Network Conference Settings Setting Description Enable Network Enables or disables network conferencing for account x.
Page 46: Call Settings
VSP715 Administrator and Provisioning Manual Call Settings You can configure call settings for each account. Call Settings include Do Not Disturb and Call Forward settings. The call settings are also available as parameters in the configuration file. See “"call_settings" Module: Call Settings” on page 130.
Page 47: Call Forward
VSP715 Administrator and Provisioning Manual Call Forward Setting Description Enable Call Forward Enables or disables call forwarding for all calls on that line. Always Select to enable. Target Number Enter a number to which all calls will be forwarded. Enable Call Forward Enables or disables forwarding incoming calls to the target Busy number if the number of active calls has reached the...
Page 48: User Preferences
VSP715 Administrator and Provisioning Manual User Preferences On the User Preferences page, you can configure some basic settings for the phone and set hold reminder and call waiting settings. The User Preferences page is also available to phone users when they log on to the WebUI. The user preference settings are also available as parameters in the configuration file.
Page 49: Call Hold Reminder
VSP715 Administrator and Provisioning Manual Call Hold Reminder Setting Description Enable Call Hold Enables or disables the call hold reminder tone. Select to Reminder Tone enable. Tone Interval (secs) Sets the interval for the call hold reminder tone, in seconds. Call Waiting Setting Description...
Page 50: Programmable Keys
VSP715 Administrator and Provisioning Manual Programmable Keys The VSP715 has 2 dual-function programmable keys. You can assign functions to the programmable keys on the Programmable Keys page. Keys can have identical functions, depending on the "Type" of key. For example, you can assign several Account keys to Account 1 to enable users to manage multiple calls on Account 1.
Page 51 VSP715 Administrator and Provisioning Manual Programmable Key Type Description Call Forward All Configures the key to turn Call Forward All on or off. In the Account column, select the account for which Call Forward All will apply. Before assigning the key, ensure that you configure Call Forward settings on the Call Settings page.
Page 52 VSP715 Administrator and Provisioning Manual Programmable Key Type Description Multicast Page Configures the key to make outgoing multicast pages. In the Value column, enter a valid Paging Zone ID (ranging from 1 to 10). Multicast paging differs from standard paging in that it is handled locally by the VSP715 and does not require a subscription through the hosted server.
Page 53: Speed Dial Keys
VSP715 Administrator and Provisioning Manual Programmable Key Type Description Direct Call Pickup Enables the user to answer a call ringing at a specific VSP715 or compatible SIP telephone. Pressing the key dials the Direct Call Pickup feature access code (FAC) configured on the SIP Account Management page.
Page 54: Speed Dial Keys
VSP715 Administrator and Provisioning Manual Speed Dial Keys Click the link for each setting to see the matching configuration file parameter in “"speed_dial" Module: Speed Dial Settings” on page 134. Setting Description Name The name associated with the speed dial entry. Value The phone number that the speed dial key dials when pressed and held.
Page 55: Signaling Settings
VSP715 Administrator and Provisioning Manual Signaling Settings The signalling settings are also available as parameters in the configuration file. See “"network" Module: Network Settings” on page 108. After entering information on this page, click to save it. Voice Click the link for each setting to see the matching configuration file parameter in “"network"...
Page 56: Ringer Settings
VSP715 Administrator and Provisioning Manual Ringer Settings The Ringer Settings enable you to provide a distinctive ringing feature via the custom Alert-Info header associated with an incoming call. This setting overrides the ringer tone you have set for the account. For example, you can set a unique ringer tone to alert the VSP715 user upon receiving any incoming calls tagged as "important"...
Page 57: Paging Zone
VSP715 Administrator and Provisioning Manual Paging Zone On the Paging Zone page, you can enter the multicast IP addresses that the phone will monitor. When a page is sent out using this multicast IP address, all phones that are programmed to monitor that IP address will receive the paging RTP stream and play the page on their speakerphone.
Page 58: Network Pages
VSP715 Administrator and Provisioning Manual Network Pages You can set up the VSP715 for your network configuration on the Network pages. Your service provider may require you to configure your network to be compatible with its service, and the VSP715 settings must match the network settings. The network settings are also available as parameters in the configuration file.
Page 59: Advanced Network Settings
VSP715 Administrator and Provisioning Manual Setting Description Primary DNS If DHCP is disabled or you don't wish to use the DHCP-assigned DNS server (or one specified by your Secondary DNS service provider), enter addresses for the primary and secondary DNS servers. Advanced Network Settings VLAN You can organize your network and optimize VoIP performance by creating a virtual LAN...
Page 60: Lldp-Med
VSP715 Administrator and Provisioning Manual Setting Description Enter the PC Port VLAN ID (vlan 5, for example). Priority Select the VLAN priority that matches the Quality of Service (QOS) settings that you have set for that VLAN ID. Outbound SIP packets will be marked and sent according to their priority.
Page 61: Contacts Pages
VSP715 Administrator and Provisioning Manual Contacts Pages Local Directory On the Local Directory page, you can manage your local directory entries. You can sort, edit, delete, and add contact information for up to 200 entries. In order to back up your contacts or import another local directory file, the page also enables you to export and import your phone's local directory.
Page 62 VSP715 Administrator and Provisioning Manual Table 8. Local Directory commands Click To... Sort the list by last name. Edit information for an entry View the next page of entries. View the last page of entries. View the first page of entries. Delete selected entries from the directory.
Page 63: Create Local Directory Entry
VSP715 Administrator and Provisioning Manual Create Local Directory Entry Setting Description Range Default First Name Enter the appropriate names in these fields. The maximum length Blank Last Name of the first name and last name fields is 15 characters. Ringer Tone Sets a unique ringer tone for calls Auto, Tone 1-10 Tone 1...
Page 64: Blacklist
VSP715 Administrator and Provisioning Manual Blacklist On the Blacklist page, you can manage local blacklist entries. The VSP715 rejects calls from numbers that match blacklist entries. You can sort, edit, delete, and add up to 200 blacklist entries. In order to back up your blacklist entries or import another local blacklist file, the page also enables you to export and import the blacklist.
Page 65: Create Blacklist Entry
VSP715 Administrator and Provisioning Manual Table 9. Blacklist commands Click To... Add a new entry. Delete all entries. Import a blacklist file. Export the blacklist. To add a new blacklist entry: 1. Click The Create Blacklist Entry page appears. 2. Enter the required information as described in the following table. Create Blacklist Entry Setting Description...
Page 66: Blacklist Import/Export
VSP715 Administrator and Provisioning Manual Blacklist Import/Export The best way to create a blacklist file for import is to first export the blacklist from the VSP715. After exporting the file, open it in an .xml editor and add or modify entries. Importing a blacklist file adds the imported blacklist entries to existing entries.
Page 67: Ldap
VSP715 Administrator and Provisioning Manual LDAP The phone supports remote Lightweight Directory Access Protocol (LDAP) directories. An LDAP directory is hosted on a remote server and may be the central directory for a large organization spread across several cities, offices, and departments. You can configure the phone to access the directory and allow users to search the directory for names and telephone numbers.
Page 68 (no spaces). Your directory may include attributes like "cn" (common name) or "ou" (organizational unit) or "dc" (domain component). For example: ou=accounting,dc=vtech,dc=com Maximum number of Sets the maximum number of entries returned for an LDAP entries search.
Page 69 VSP715 Administrator and Provisioning Manual Setting Description Work number attribute Sets the attribute for the work number. What you enter here should match the work number attribute for entries on the LDAP server (telephoneNumber, for example). This helps ensure that the phone displays LDAP entries in the same format as the Local Directory.
Page 70: Broadsoft
VSP715 Administrator and Provisioning Manual Broadsoft The phone supports access to the Broadsoft Phonebook. Users can search for and call contacts that are hosted on the Broadsoft Phonebook. On the Broadsoft Phonebook Settings page, you must enter the path and credentials to enable the phone to access the Broadsoft Phonebook.
Page 71: Call History
VSP715 Administrator and Provisioning Manual Call History The Call History page has no configurable settings. It displays Missed Calls, Received Calls, and Dialed Calls. Users can view their call history and "click to dial" numbers if click to dial is enabled. Back to Contents Using the WebUI...
Page 72: Servicing Pages
VSP715 Administrator and Provisioning Manual Servicing Pages Reboot To manually reboot the VSP715 and apply settings that you have updated, click Time and Date On the Time and Date page, you can manually set the time and date, and the time and date formats.
Page 73: Time And Date Format
VSP715 Administrator and Provisioning Manual Time and Date Format Click the link for each setting to see the matching configuration file parameter in “"time_date" Module: Time and Date Settings” on page 115. Default values and ranges are listed there. Setting Description Date Format Sets the date format.
Page 74: Manual Time Settings
VSP715 Administrator and Provisioning Manual Setting Description DST End: Month If User-defined DST is enabled, set the end date and time for daylight savings: Month, week, day, and hour. DST End: Week DST End: Day DST End: Hour Daylight Savings Offset If User-defined DST is enabled, this specifies the daylight savings adjustment (in minutes) to be applied when the current time is between Daylight Savings Start and...
Page 75: Firmware Upgrade
VSP715 Administrator and Provisioning Manual Firmware Upgrade You can update the VSP715 with new firmware using the following methods:  Retrieving a firmware update file from a remote host computer and accessed via a URL. This central location may be arranged by you, an authorized ErisTerminal dealer, or your SIP service provider.
Page 76: Manual Firmware Update And Upload
VSP715 Administrator and Provisioning Manual Manual Firmware Update and Upload On the Manual Firmware Update Settings page, you can upgrade the VSP715 firmware using a file located on your computer or local network. To update the firmware using a file on your computer or local network: 1.
Page 77: Provisioning
VSP715 Administrator and Provisioning Manual Provisioning Provisioning refers to the process of acquiring and applying new settings for the VSP715 using configuration files retrieved from a remote computer. After a VSP715 is deployed, subsequent provisioning can update the VSP715 with new settings; for example, if your service provider releases new features.
Page 78: Provisioning Settings
VSP715 Administrator and Provisioning Manual Provisioning Settings Setting Description Server URL URL of the provisioning file(s). The format of the URL must be RFC 1738 compliant, as follows: "<schema>://<user>:<password>@ <host>:<port>/<url-path>" "<user>:<password>@" may be empty. "<port>" can be omitted if you do not need to specify the port number.
Page 79: Dhcp Settings
VSP715 Administrator and Provisioning Manual DHCP Settings Setting Description Use DHCP Options Enables the VSP715 to use DHCP options to locate and retrieve the configuration file. When selected, the VSP715 automatically attempts to get a provisioning server address, and then the configuration file. If DHCP options do not locate a configuration file, then the server provisioning string is checked.
Page 80: Resynchronization
VSP715 Administrator and Provisioning Manual Resynchronization Setting Description Mode Sets which files the VSP715 checks for at regular intervals. It can check for configuration files, firmware update files (from the URL entered on the Firmware Server Settings page), or both. Note: When checking for both configuration and firmware files, the firmware URL can be within the config file.
Page 81: Export Configuration
VSP715 Administrator and Provisioning Manual Export Configuration You can export all the settings you have configured on the WebUI and save them as a configuration file on your computer. You can then use this configuration file as a backup, or use it to update other phones.
Page 82: Security
VSP715 Administrator and Provisioning Manual Security On the Security page you can reset the admin password, reset the user password, and enter web server settings. The security settings are also available as parameters in the configuration file. See “"web" Module: Web Settings” on page 125.
Page 83: Web Server
VSP715 Administrator and Provisioning Manual Web Server Setting Description HTTP Server port Port used by the HTTP server. Enable Secure Browsing Sets the server to use the HTTPS protocol. HTTPS Server port Port used by the HTTPS server. To configure Web Server Settings: 1.
Page 84: System Logs
VSP715 Administrator and Provisioning Manual System Logs On the Syslog Settings page, you can enter settings related to system logging activities. It supports the following logging modes:  Syslog server  Volatile file Under Network Trace, you can capture network traffic related to the phone's activity and save the capture as a .pcap file.
Page 85: Network Trace
VSP715 Administrator and Provisioning Manual The logging levels are:  CRITICAL: Operating conditions to be reported or corrected immediately (for example, an internal component failure or file system error).  ERROR: Non-urgent failures—unexpected conditions that won't cause the device to malfunction. ...
Page 86: Provisioning Using Configuration Files
VSP715 Administrator and Provisioning Manual H A P T E R ROVISIONING SING ONFIGURATION ILES Provisioning using configuration files is the quickest way to configure multiple VSP715 desksets and other ErisTerminal products. You can place configuration files on a provisioning server, where the VSP715 desksets retrieve the files and update their configuration automatically.
Page 87: The Provisioning Process
General file: <model>.cfg.  MAC-specific file: <model>_<MAC Address>.cfg. The <model> variable is the VTech product model: VSP715, for example. If the provisioning URL specifies both a path and filename, then the VSP715 retrieves only the configuration file specified. 3. The VSP715 restarts after one minute of inactivity. Please wait while the phone reboots appears on the VSP715 screen.
Page 88: Resynchronization: Configuration File Checking
VSP715 Administrator and Provisioning Manual “Configuration File Parameter Guide” on page 94 for the options and value ranges available for each configuration file setting. Resynchronization: configuration file checking You can select a number of options that determine when the VSP715 checks for new configuration files.
Page 89: Configuration File Types
 General file: <model>.cfg  MAC-specific file: <model>_<MAC Address>.cfg The <model> variable is the VTech product model; for example, VSP725. For more information about the MAC-specific configuration file, see “Guidelines for the MAC-Specific configuration file” on page If the provisioning URL specifies a path only with no filename, then by default the VSP715 will fetch both files.
Page 90: Data Files
VSP715 Administrator and Provisioning Manual Data Files The configuration file can also include links to data files for product customization. Allowed data types include the following:  Directory (contacts, blacklist) in .xml format  Certificates (server, provisioning, LDAP, Broadsoft) in pem format ...
Page 91: Configuration File Tips And Security
VSP715 MAC address, which is printed on a label on the back of the device, or available on the MENU > Status > Product Info screen. For example, a VTech VSP715 deskset with the MAC address of 00:11:A0:10:6F:2D would download the VSP715_0011A0106F2D.cfg file.
Page 92: Securing Configuration Files With Aes Encryption
VSP715 Administrator and Provisioning Manual Securing configuration files with AES encryption You can encrypt your configuration files to prevent unauthorized users modifying the configuration files. The VSP715 firmware decrypts files using the AES 256 algorithm. After encrypting a file and placing it on your provisioning server, you can enable the VSP715 to decrypt the file after fetching it from the server.
Page 93 VSP715 Administrator and Provisioning Manual To enable configuration file decryption: 1. On the WebUI, click Servicing > Provisioning. 2. On the Provisioning page under Resynchronization, select Use Encryption for configuration file. 3. Enter the 16-character passphrase that you created when you encrypted the configuration file.
Page 94: Configuration File Parameter Guide
VSP715 Administrator and Provisioning Manual H A P T E R ONFIGURATION ARAMETER UIDE This chapter lists the available options for all the settings within the VSP715 configuration file. Most settings in the configuration file have an equivalent in the WebUI (see the settings tables in “Using the WebUI”...
Page 95: Sip_Account" Module: Sip Account Settings
VSP715 Administrator and Provisioning Manual  “"file" Module: Imported File Settings” on page 136  “"tone" Module: Tone Definition Settings” on page 139  “"profile" Module: Password Settings” on page 142  “"page_zone" Module: Paging Zone Settings” on page 143 ...
Page 96 VSP715 Administrator and Provisioning Manual Setting: sip_account.x.inter_digit_timeout Description: Sets the inter-digit timeout (in seconds) for account x. The inter-digit timeout sets how long the VSP715 waits after the last digit is entered before dialing the number. Values: 1–10 Default: Setting: sip_account.x.maximum_call_number Description: Sets the maximum number of concurrent active calls allowed for that...
Page 97 VSP715 Administrator and Provisioning Manual Setting: sip_account.x.primary_sip_server_port Description: Sets the SIP server port for account x. Values: 1–65535 Default: 5060 Setting: sip_account.x.primary_registration_server_address Description: Sets the registration server IP address for account x. Values: Text string Default: Blank Setting: sip_account.x.primary_registration_server_port Description: Sets the registration server port for account x.
Page 98 VSP715 Administrator and Provisioning Manual Setting: sip_account.x.backup_outbound_proxy_server_port Description: Sets the backup outbound proxy server port for account x. Values: 1–65535 Default: 5060 Setting: sip_account.x.codec_priority.1 Description: Sets the highest-priority codec for account x. Values: g711u, g711a, g729a/b, Default: g711u g726, g722 Setting: sip_account.x.codec_priority.2 Description:...
Page 99 VSP715 Administrator and Provisioning Manual Setting: sip_account.x.g729_annexb_enable Description: Enables G.729 Annex B, with voice activity detection (VAD) and bandwidth-conserving silence suppression. This setting applies only when G.729a/b is selected in a sip_account.x.codec_priority parameter. Values: 0 (disabled), 1 (enabled) Default: Setting: sip_account.x.dscp Description: Sets the Voice Quality of Service Layer 3 - DSCP for account x.
Page 100 VSP715 Administrator and Provisioning Manual Setting: sip_account.x.access_code_park_call Description: Sets the Call Park feature access code for account x. Values: Text string Default: Blank Setting: sip_account.x.access_code_retrieve_parked_call Description: Sets the retrieve parked call feature access code for account x. Values: Text string Default: Blank Setting:...
Page 101 VSP715 Administrator and Provisioning Manual Setting: sip_account.x.access_code_cfna_off Description: Sets the Call Forward No Answer OFF feature access code for account x. Values: Text string Default: Blank Setting: sip_account.x.access_code_cfb_on Description: Sets the Call Forward Busy ON feature access code for account x. Values: Text string Default:...
Page 102 VSP715 Administrator and Provisioning Manual Setting: sip_account.x.access_code_call_waiting_off Description: Sets the Call Waiting OFF feature access code for account x. Values: Text string Default: Blank Setting: sip_account.x.access_code_group_call_pickup Description: Sets the Group Call Pickup feature access code for account x. Values: Text string Default: Blank Setting:...
Page 103 VSP715 Administrator and Provisioning Manual Setting: sip_account.x.mwi_subscription_expires Description: Sets the MWI subscription expiry time (in seconds) for account x. Values: 0–65535 Default: 3600 Setting: sip_account.x.mwi_ignore_unsolicited Description: Enables or disables ignoring of unsolicited MWI notifications— notifications in addition to, or instead of, SUBSCRIBE and NOTIFY methods—for account x.
Page 104 VSP715 Administrator and Provisioning Manual Setting: sip_account.x.nat_traversal_udp_keep_alive_interval Description: Sets the interval (in seconds) for sending UDP keep-alives. Values: 0–65535 Default: Setting: sip_account.x.music_on_hold_enable Description: Enables or disables a hold-reminder tone that a far-end caller hears when put on hold during a call on account x. Values: 0 (disabled), 1 (enabled) Default:...
Page 105: Mac-Specific Configuration File Settings
VSP715 Administrator and Provisioning Manual Setting: sip_account.use_first_trusted_certificate_for_all Description: Enables or disables accepting the first TLS certificate for all accounts. Values: 0 (disabled), 1 (enabled) Default: MAC-specific configuration file settings Setting: sip_account.x.park_variant Description: Selects how the VSP715 handles call parking, depending on the service provider.
Page 106 VSP715 Administrator and Provisioning Manual Setting: sip_account.x.user_id Description: Sets the account ID for account x. Depending on your service provider's specifications, this could be an extension number. Note: Do not enter the host name (e.g. "@sipservice.com"). The configuration file automatically adds the default host name. Values: Text string Default:...
Page 107 VSP715 Administrator and Provisioning Manual Setting: sip_account.x.mwi_uri Description: Sets the MWI URI that will be used for MWI subscription. If this setting is left blank, the VSP715 uses the account x user ID for MWI subscription. Values: SIP URI text string Default: Blank Back to Contents...
Page 108: Network" Module: Network Settings
VSP715 Administrator and Provisioning Manual "network" Module: Network Settings The network settings follow the format: network.[element]. General configuration file settings Setting: network.rtp.port_start Description: Sets the Local RTP port range start. Values: 1–65535 Default: 18000 Setting: network.rtp.port_end Description: Sets the Local RTP port range end. Values: 1–65535 Default:...
Page 109 Default: Blank Setting: network.vendor_class_id Description: Sets the vendor ID for DHCP option 60. Values: Text string Default: Vtech Vesa VSP715 Setting: network.user_class Description: Sets the user class for DHCP option 77. Values: Text string Default: Vtech Vesa VSP715 Back to Contents...
Page 110: Mac-Specific Configuration File Settings
VSP715 Administrator and Provisioning Manual Setting: network.ip_dns_cache_clear_timeout Description: Sets the interval (in minutes) between removing all caching and performing a new DNS lookup. Set to 0 to remove all caching and perform a DNS lookup for every outgoing request and response (TTL=0 emulation).
Page 111 VSP715 Administrator and Provisioning Manual Setting: network.ip.static_ip_addr Description: Sets a static IP address for the network. Values: Text string (IPv4) Default: Blank Setting: network.ip.subnet_mask Description: Sets the subnet mask for the network. Values: Text string (IPv4) Default: Blank Setting: network.ip.gateway_addr Description: Sets the Gateway IP address.
Page 112: Provisioning" Module: Provisioning Settings
VSP715 Administrator and Provisioning Manual "provisioning" Module: Provisioning Settings The provisioning settings follow the format: provisioning.[element]. All these settings are exported when you manually export the configuration from the VSP715. All the provisioning settings are included in the general configuration file. Setting: provisioning.click_to_dial Description:...
Page 113 VSP715 Administrator and Provisioning Manual Setting: provisioning.server_password Description: Sets the authentication password for the provisioning server. Values: Text string Default: Blank Setting: provisioning.dhcp_option_enable Description: Enables or disables using DHCP options for locating the configuration and firmware files. Values: 0 (disabled), 1 (enabled) Default: Setting: provisioning.dhcp_option_priority_1...
Page 114 VSP715 Administrator and Provisioning Manual Setting: provisioning.resync_time Description: Sets the interval (in minutes) between checks for new firmware and/or configuration files. Values: 0–65535 Default: 0 (OFF) Setting: provisioning.remote_check_sync_enable Description: Enables or disables remotely triggering the device to check for new firmware and/or configuration files.
Page 115: Time_Date" Module: Time And Date Settings
VSP715 Administrator and Provisioning Manual "time_date" Module: Time and Date Settings The time and date settings follow the format: time_date.[element]. All these settings are exported when you manually export the configuration from the VSP715. All the time and date settings are included in the general configuration file. Setting: time_date.date_format Description:...
Page 116 VSP715 Administrator and Provisioning Manual Values: Pacific/Pago_Pago, Pacific/Honolulu, Default: America/New_York America/Adak, America/Anchorage, America/Vancouver, America/Tijuana, America/Los_Angeles, America/Edmonton, America/Chihuahua, America/Denver, America/Phoenix, America/Winnipeg, Pacific/Easter, America/Mexico_City, America/Chicago, America/Nassau, America/Montreal, America/Grand_Turk, America/Havana, America/New_York, America/Caracas, America/Halifax, America/Santiago, America/Asuncion, Atlantic/Bermuda, Atlantic/Stanley, America/Port_of_Spain, America/St_Johns, America/Godthab, America/Argentina/Buenos_Aires, America/Fortaleza, America/Sao_Paulo, America/Noronha, Atlantic/Azores, GMT, America/Danmarkshavn, Atlantic/Faroe, Europe/Dublin, Europe/Lisbon,...
Page 117 VSP715 Administrator and Provisioning Manual Setting: time_date.daylight_saving_auto_adjust Description: Sets the device to automatically adjust clock for daylight savings. Values: 0 (disabled), 1 (enabled) Default: Setting: time_date.daylight_saving_user_defined Description: Enables or disables manual daylight savings configuration. Values: 0 (disabled), 1 (enabled) Default: Setting: time_date.daylight_saving_start_month Description:...
Page 118 VSP715 Administrator and Provisioning Manual Setting: time_date.daylight_saving_end_week Description: Sets the week that daylight savings time ends. Values: 1–5 Default: Setting: time_date.daylight_saving_end_day Description: Sets the day that daylight savings time ends. Values: Sunday, Monday, Tuesday, Default: Sunday Wednesday, Thursday, Friday, Saturday Setting: time_date.daylight_saving_end_hour Description:...
Page 119: Log" Module: Log Settings
VSP715 Administrator and Provisioning Manual "log" Module: Log Settings The log settings control system logging activities. System logging may be required for troubleshooting purposes. The following logging modes are supported:  Serial/Console—system log output to an external console using a serial/RS-232 cable ...
Page 120: Remotedir" Module: Remote Directory Settings
VSP715 Administrator and Provisioning Manual "remoteDir" Module: Remote Directory Settings The remote directory settings follow the format: remoteDir.[element]. All these settings are exported when you manually export the configuration from the VSP715. All the remote directory settings are included in the general configuration file. Setting: remoteDir.ldap_enable Description:...
Page 121 Sets the LDAP search base. This sets where the search begins in the directory tree structure. Enter one or more attribute definitions, separated by commas (no spaces). Your directory may include attributes like "cn" (common name) or "ou" (organizational unit) or "dc" (domain component). For example, ou=accounting,dc=vtech,dc=com Values: Text string Default:...
Page 122 VSP715 Administrator and Provisioning Manual Setting: remoteDir.ldap_number_filter Description: Sets the LDAP number filter. Values: Text string Default: Blank Setting: remoteDir.ldap_firstname_attribute Description: Sets the name attributes. Enter the name attributes that you want the VSP715 to display for each entry returned after an LDAP search. Separate each attribute with a space.
Page 123 VSP715 Administrator and Provisioning Manual Setting: remoteDir.ldap_incall_lookup_enable Description: Enables or disables LDAP incoming call lookup. If enabled, the VSP715 searches the LDAP directory for the incoming call number. If the number is found, the VSP715 uses the LDAP entry for CID info. Values: 0 (disabled), 1 (enabled) Default:...
Page 124 VSP715 Administrator and Provisioning Manual Setting: remoteDir.broadsoft_password Description: Sets the Broadsoft Phonebook authentication password. Values: Text string Default: Blank Setting: remoteDir.broadsoft_dir_type Description: Sets the Broadsoft Phonebook directory type. Values: Group, GroupCommon, Default: Group Enterprise, EnterpriseCommon, Personal Setting: remoteDir.ldap_check_certificate Description: Enables or disables accepting only a trusted LDAP certificate. Values: 0 (disabled), 1 (enabled) Default:...
Page 125: Web" Module: Web Settings
VSP715 Administrator and Provisioning Manual "web" Module: Web Settings The web settings control the web server IP, port, and security settings. The web settings follow the format: web.[element]. All the web settings are included in the general configuration file. Setting: web.http_port Description: Sets the http port when http is enabled.
Page 126: User_Pref" Module: User Preference Settings
VSP715 Administrator and Provisioning Manual "user_pref" Module: User Preference Settings The user settings are accessible to the VSP715 user. These settings are useful for initial setup. You may wish to remove these settings from auto-provisioning update files so that users do have their own settings overwritten. The user preference settings follow the format: user_pref.[element].
Page 127: Mac-Specific Configuration File Settings
VSP715 Administrator and Provisioning Manual MAC-specific configuration file settings Setting: user_pref.language Description: Sets the language that appears on the device screen. English, French and Spanish are available. Values: en, fr, es Default: Setting: user_pref.idle_to_logo_timeout Description: Sets the delay (in seconds) before the logo replaces the idle screen. Values: 0 (disabled)–300 Default:...
Page 128 VSP715 Administrator and Provisioning Manual Setting: user_pref.call_waiting.tone_enable Description: Enables or disables the call waiting tone. Values: 0 (disabled), 1 (enabled) Default: Setting: user_pref.call_waiting.tone_interval Description: Sets the interval for the call waiting tone in seconds. Values: 10–60 Default: Setting: user_pref.call_waiting.mode Description: Enables or disables rejecting calls if already on a call.
Page 129 VSP715 Administrator and Provisioning Manual Setting: user_pref.headset_volume Description: Sets the headset volume. Values: 1–9 Default: Setting: user_pref.handset_volume Description: Sets the corded handset volume. Values: 1–9 Default: Setting: user_pref.key_beep_enable Description: Enables or disables key beeps on the VSP715. Values: 0 (disabled), 1 (enabled) Default: Back to Contents Configuration File Parameter Guide...
Page 130: Call_Settings" Module: Call Settings
VSP715 Administrator and Provisioning Manual "call_settings" Module: Call Settings The call settings configure data related to a user's call preferences. The data is stored internally at /mnt/flash/CallSettings.xml. All the call settings (except one) follow the format: call_settings.account.x.[element] where x is an account number ranging from 1 to 2. All the call settings are included in the MAC-specific configuration file.
Page 131 VSP715 Administrator and Provisioning Manual Setting: call_settings.account.x.call_fwd_busy_enable Description: Enables or disables Call Forward Busy for account x. Values: 0 (disabled), 1 (enabled) Default: Setting: call_settings.account.x.call_fwd_busy_target Description: Sets the Call Forward Busy target number for account x. Values: Text string Default: Blank Setting: call_settings.account.x.cfna_enable...
Page 132: Pfk" Module: Programmable Feature Key Settings
VSP715 Administrator and Provisioning Manual "pfk" Module: Programmable Feature Key Settings The programmable feature key (PFK) settings store the data associated with each programmable feature key. The programmable feature key settings follow the format: pfk.x.[element], where x is the programmable feature key ID, ranging from 1 to 2. All the programmable feature key settings are included in the general configuration file.
Page 133 VSP715 Administrator and Provisioning Manual Setting: pfk.x.account Description: Sets the SIP account used for the assigned feature (if applicable). Values: 1–2 Default: Setting: pfk.x.page_destination Description: If required by your service provider, enter a page destination number. The target number for the outgoing page will be formed by concatenating Paging feature access code of the selected account and the PFK page destination value.
Page 134: Speed_Dial" Module: Speed Dial Settings
VSP715 Administrator and Provisioning Manual "speed_dial" Module: Speed Dial Settings The speed dial key settings configure the dial pad keys for speed dialing pre-programmed phone numbers. When configured, the VSP715 user can press and hold a dial pad key to dial a programmed phone number.
Page 135: Ringersetting" Module: Distinctive Ringer Settings
VSP715 Administrator and Provisioning Manual "ringersetting" Module: Distinctive Ringer Settings The distinctive ringer settings configure the distinctive ringer feature. For more information, “Ringer Settings” on page 56. You can configure up to 8 instances of the distinctive ringer feature. The ringer setting parameters follow the format ringersetting.x.[element], where x is the instance of the setting, ranging from 1 to 8.
Page 136: File" Module: Imported File Settings
VSP715 Administrator and Provisioning Manual "file" Module: Imported File Settings The "file" parameters enable the provisioning file to import additional configuration files of various types, including:  Contact lists  Custom logos  Security certificates The following certificates are supported: ...
Page 137: Mac-Specific Configuration File Settings
VSP715 Administrator and Provisioning Manual MAC-specific configuration file settings Setting: file.ldap.trusted.certificate Description: URI of LDAP certificate to be imported; for example, <protocol>://<user>:<password>@<host>:<port>/<url-path> Values: Text string Default: Blank Setting: file.broadsoft.trusted.certificate Description: URI of Broadsoft certificate to be imported; for example, <protocol>://<user>:<password>@<host>:<port>/<url-path> Values: Text string Default:...
Page 138 VSP715 Administrator and Provisioning Manual Setting: file.bootup_logo Description: URL of custom logo shown during bootup. For logo specifications, see “Logo specifications” on page Values: Text string Default: Blank Setting: file.idle_logo Description: URL of custom logo shown on the idle screen. For logo specifications, “Logo specifications”...
Page 139: Tone" Module: Tone Definition Settings
VSP715 Administrator and Provisioning Manual "tone" Module: Tone Definition Settings The Tone Definition settings configure data for various tones for the purpose of localization. The Audio Manager component uses the data from this model to populate the mcu on bootup. Each tone definition must be a string of 12 elements separated by a space: "<num of freq>...
Page 140 VSP715 Administrator and Provisioning Manual Setting: tone.call_waiting_tone.element.x Description: Defines the call waiting tone element x. Values: Tone element string Default: Blank Setting: tone.hold_reminder_tone.num_of_elements Description: Sets the number of tone elements for the hold reminder tone. Values: 1–5 Default: Setting: tone.hold_reminder_tone.element.1 Description: Defines the hold reminder tone element 1.
Page 141 VSP715 Administrator and Provisioning Manual Setting: tone.stutter_dial_dial_tone.element.1 Description: Defines the stutter dial tone element 1. Values: Tone element string Default: 2 440 -180 350 -180 0 0 0 0 100 100 10 Setting: tone.stutter_dial_dial_tone.element.2 Description: Defines the stutter dial tone element 2. Values: Tone element string Default:...
Page 142: Profile" Module: Password Settings
VSP715 Administrator and Provisioning Manual Setting: tone.ring_back_tone.element.1 Description: Defines the ringback tone element 1. Values: Tone element string Default: 2 440 -180 480 -180 0 0 0 0 2000 4000 65535 Setting: tone.ring_back_tone.element.x Description: Defines the ringback tone element x. Values: Tone element string Default:...
Page 143: Page_Zone" Module: Paging Zone Settings
VSP715 Administrator and Provisioning Manual "page_zone" Module: Paging Zone Settings The paging zone settings allow you to define a maximum of 10 paging zones that the VSP715 can use for multicast paging. The paging zone parameters (except for page_zone.call_priority_threshold) follow the format page_zone.x.[element], where x is the paging zone ID number, ranging from 1 to 10.
Page 144 VSP715 Administrator and Provisioning Manual Setting: page_zone.call_priority_threshold Description: Set the call_priority_threshold. If the paging zone priority (page_zone.x.priority) is higher or equal to the call priority, then a multicast page can interrupt an active, dialing, or incoming call. Values: 1–10 Default: Back to Contents Configuration File Parameter Guide...
Page 145: Softkey" Module: Custom Soft Key Settings
VSP715 Administrator and Provisioning Manual "softkey" Module: Custom Soft Key Settings The custom soft key settings allow you to select which soft keys can appear on the Idle screen, the Call Active screen, the Call Held screen and the Live Dial screen. You can also specify the position of each soft key.
Page 146: Troubleshooting
If you have difficulty with your VSP715 deskset, please try the suggestions below. For customer service or product information, contact the person who installed your system. If your installer is unavailable, visit our website at businessphones.vtech.com or call 1 (888) 370-2006. Common Troubleshooting Procedures Follow these procedures to resolve common issues.
Page 147 VSP715 Administrator and Provisioning Manual My computer can't connect to the network after plugging the Ethernet cable through the PC port.  Make sure the VSP715 is connected to power. The PC port does not work when the VSP715 does not have power source or during a power outage. ...
Page 148: Appendixes
VSP715 Administrator and Provisioning Manual PPENDIXES Appendix A: Specifications Operating temperature: 32–122 °F (0–50 °C) AC Adapter Input: 100–240 Vac, 50/60 Hz, 200 mA (max.) Output: 5.0 Vdc @ 700 mA Ethernet network ports: 10/100 Mbps RJ-45 Ports Back to Contents Appendixes...
Page 149: Appendix B: Soft Keys
VSP715 Administrator and Provisioning Manual Appendix B: Soft Keys The table below provides an alphabetical list of the labels that appear above the VSP715 soft keys. Label Description Selects the text format for input abc/ABC/123 Displays the new directory group editor Enters dot in IP editing field Add dot Answers an incoming call...
Page 150 VSP715 Administrator and Provisioning Manual Label Description Returns to the previous screen Rejects an incoming call Reject Resumes a call put on hold Resume 1) Saves current setting 2) Begins save process Save Opens the Directory search editor; begins a search Search Selects a highlighted option Select...
Page 151: Appendix C: Maintenance
VSP715 Administrator and Provisioning Manual Appendix C: Maintenance Taking care of your telephone  Your VSP715 deskset contains sophisticated electronic parts, so you must treat it with care.  Avoid rough treatment.  Place the corded handset down gently.  Save the original packing materials to protect your VSP715 deskset if you ever need to ship it.
Page 152: Appendix D: Gpl License Information
Beaverton OR 97008 ATTN: Information Technology Group — VSP715 GPL code request If your request does not fully comply with the foregoing requirements, VTech reserves the right to reject your request. Further, by requesting and receiving the available code, you release VTech, its affiliates, and its and their officers, directors, employees, and representatives (“VTech Parties”) from any liability or responsibility relating to such code,...

VTech ErisTerminal VSP715 Administrator And Provisioning Manual

Quick Links

Related Manuals for VTech ErisTerminal VSP715

Summary of Contents for VTech ErisTerminal VSP715

Table of Contents