Page 1 Commercial Frontload Washers Refer to Page 3 for Model Numbers Front Control Washers Rear Control H018C Washers Part No. 800383R3 www.comlaundry.com November 2011...
Page 3: Table Of Contents
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 4 Models HWR261*E, HWR261*H, SWR261*E and SWR261*H ..........155 Models HWRB61*J1102, SWRB61*H, SWRB61*J, SWRC61*J, SWRD61*H, SWRF61*J and SWRH61*J ......156 Models HWRT61*H, HWRT61*H1102, HWRY61*H1102, HWRZ61*H, HWRZ61*H1102, SWRT61*H, SWRY61*H and SWRZ61*H ............157 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 5: Model Identification
HWRZ61*H1102 SWR261*E SWR261*H SWRB61*H SWRB61*J SWRC61*J SWRD61*H SWRF61*J SWRH61*J SWRT61*H SWRY61*H SWRZ61*H * Add Letter To Designate Color. L – Almond W – White Q – Bisque 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 7: Section 1 - Safety Information
• Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the product is properly grounded and to reduce the risk of fire, electric shock, serious injury or death. W006R2 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 8: Locating An Authorized Servicer
Locating an Authorized Servicer Alliance Laundry Systems is not responsible for personal injury or property damage resulting from improper service. Review all service information before beginning repairs. Warranty service must be performed by an authorized technician, using authorized factory parts. If service is required after the warranty expires, Alliance Laundry Systems also recommends contacting an authorized technician and using authorized factory parts.
Page 9: Section 2 - Introduction
When calling or writing about your product, be sure to mention model and serial numbers. Model and serial numbers are located on nameplate(s) as shown. NAMEPLATE LOCATION H129PE1A 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 10: How Your Washer Works
(Located in control hood) (Located in control hood) TEMPERATURE SWITCH SPEED TIMER SWITCH (Located in meter case) MIXING VALVE INNER BASKET OUTER MOTOR ELECTRIC DRAIN PUMP H197SE3A REAR CONTROL WASHERS © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 11 The spin speeds and duration of this final high spin cycle are determined by the type of wash cycle selected (see table). 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 12: How Your Washer Works
MOTOR (Located inside CONTROL BOARD control hood) (Located inside control hood) ELECTRONIC CONTROL (Located inside control hood) MIXING VALVE INNER BASKET FLW1650S OUTER ELECTRIC DRAIN PUMP MOTOR © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 13 If this switch opens during a spin step the motor wash cycle selected (see table). control immediately stops the spin step and restarts the spin step. 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 15: Section 3 - Troubleshooting
IMPORTANT: Do not bend or damage mechanical parts within coin drop. Additional coins following path to sensor Coin in Coin Slot Coin Drop Sensor DRY2B Figure 1 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 16 Do coins Replace fall freely coin drop. through drop? Replace coin drop sensor. SWD1714S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 17 Left Tab Right Side of MIX2B Tension Spring Figure 5 (4) Use screwdriver to move spring Coin Drop Cover approximately 3 mm to left. MIX6B Figure 3 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 18 (8) Lift spring, with attached clip, off drop. (9) Remove clip from spring. Refer to Figure 7. Clip MIX4B Figure 7 (10) Attach clip to new tension spring, Part No. 209/00598/02. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 19 (14) Push spring to right until it snaps into position. Refer to Figure 5. (15) Close coin drop cover. (16) Move tension spring over cover catch. Refer to Figure 4. 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 20: No Spin Condition - Models Through Serial No. 9811005967
The knocking sound is made when the flat spot hits the pulley. The knocking may occur during a pulse spin and fade after reaching a higher RPM. To correct this condition, replace the washer belt. Refer to Paragraph 51. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 21 W003 OUT-OF-BALANCE SWITCH BALLAST WEIGHT PLASTIC WIRE RETAINER WIRE HARNESS (8 inch slack) 1-1/2 INCHES LEFT FRONT SHOCK WASHER BASE H006B TAPE Figure 10 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 22: No Motor Rotation, Or Drive Failure Code "E:df" On Electronic Display Units
3), or if there is continuity between any terminal and the motor housing. e. An open circuit between terminals 4 and 5 indicates a stuck or worn brush. Refer to appropriate service procedure on the following pages. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 23 NOTE: The copper braided wire should be located in the center of the brush assembly. If the braided wire has fallen to the bottom of the brush, it will cause binding. 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 24 Recheck resistance between motor terminals 4 and 5 to verify the brush position has been corrected. f. Reinstall motor in washer. g. Run washer through cycle to verify proper operation. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 25 Inspect both brushes to determine if either brush is worn. Refer to Figures 13 and 14. GOOD BRUSH BRUSH – Has visible amount of brush HOLDER material remaining. BRUSH SPRING BRUSH FLW1648S FLW1648S Figure 13 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 26 If there is a visible amount of brush left, use a screwdriver or similar device to push brush back and forth to loosen and remove dust. Refer to Figure 13. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 27: Electromechanical Models
• Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 28: Start Up
Actuator, control relay “CR2” row 2 (normally open contacts), the coil of “CR1” turning off Close Door light through “CR2” row 1 (normally open contacts) and to auto transformer. 20VAC is present on motor control board between H4-1 and FS2. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 29 Section 3 Troubleshooting (Electromechanical Models) POWER VEND SATISFIED-DOOR CLOSED NEUTRAL 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 30: Start And Door Lock
Motor control board closes “RL7” powering door lock actuator. Door Lock switch closes providing 240 Volt at “FS5” on motor control board and motor action begins. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 31 Section 3 Troubleshooting (Electromechanical Models) POWER START AND DOOR LOCK NEUTRAL 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 32: Fill Sequence
“L1” voltage is removed from “H3-7” and fill valves. The motor control board will then open neutral to fill valves. Should an overfill condition occur, “L1” voltage is removed from fill valves. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 33 Section 3 Troubleshooting (Electromechanical Models) POWER FILL NEUTRAL 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 34: Volt Control
The motor control board connector “H3” supplies 20 Volts control power to temp select switch, and out-of-balance switch. The motor control board connector “H5” supplies 20 Volts control power to motor tachometer for current sensing. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 35 Section 3 Troubleshooting (Electromechanical Models) 120 VOLT 20 VOLT CONTROL POWER - 20 VOLT NEUTRAL 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 36: Volt Motor Power
The 240 Volt AC goes through fuse on motor control board to Motor DC power supply, and changed to 240 Volts DC for motor operation. The motor assembly uses 190 to 240 Volt DC to run. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 37 Section 3 Troubleshooting (Electromechanical Models) 120 VOLT 240 VOLT POWER - 240 VOLT NEUTRAL 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 38: Timer Chart
Section 3 Troubleshooting (Electromechanical Models) 10. TIMER CHART H223SE3A © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 39: Cycle Timer Motor Control Inputs
Perm. press high spin (975-1025 rpm) 30 sec. timer motor pause and 60 sec. max. time (for perm. press cycle) Key: 0 = Open X = Closed Figure 15 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 40: Cycle Timer Water Fill Input Logic
X Fill Cold Temp. Water – No Flush Valves X Fill Cold Temp. Water – No Flush Valves Key: 0 = Open; X = Closed Figure 16 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 41: Washer "Dc" Motor Functions
• The other direction RL3 and RL4 are operated. Refer to Figure 17. MOTOR DC POWER SUPPLY FUS1 7 AMP 250 V "DC" Voltage FIELD ROTOR TACH H092SE3C Motor Assembly (Agitate) Figure 17 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 42 (D1, D3) of motor. Refer to Figure 19. MOTOR DC POWER SUPPLY FUS1 7 AMP 250 V "DC" Voltage FIELD ROTOR TACH H094SE3C Motor Assembly (Low Spin – 0 to 650 rpm) Figure 18 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 43 W003 MOTOR DC POWER SUPPLY FUS1 7 AMP 250 V "DC" Voltage FIELD ROTOR TACH H095SE3C Motor Assembly (High Spin – 650 to 1000 rpm) Figure 19 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 44: Control System Faults
END OF SLIDE END OF SLIDE EXTENSION TO EXTENSION TO “L” BRACKET HOLE “L” BRACKET HOLE IS 3/4 INCH IS 9/16 INCH WRONG EXTENSION CORRECT EXTENSION FLW1189B Figure 20 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 45: Netmaster Models
• Never start the washer with any guards/panels removed. • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 46: Microwand Does Not Communicate With Control
"E:OF" out properly. or "-C-"? E:OF Turn IR communication on Has IR communication (refer to been turned off? programming manual). Change electronic control and repeat procedure. FLW296S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 47: Coins Ignored When Entered
Replace the Properly reseat Properly reseat coin drop. connection and connection and Replace electronic conduct diagnostic conduct diagnostic control. test again. test again. FLW297S 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 48: No Visible Display On Control
"H1-3" control the transformer? transformer. transformer? board? Make sure "H1" Correct wiring connector is between Replace seated properly. transformer and transformer. Replace control. control board. FLW298S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 49 COLD OPTOISOLATORS POWER SUPPLY FUS1 TAN/WHT 7 AMP SOFTENER 250 VOLT YEL/BLK LOW VOLTAGE DETERGENT/BLEACH CONTROL LOGIC CIRCUIT MOTOR CONTROL ASSEMBLY FIELD ROTOR TACH MOTOR ASSY FLW299S 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 50: Washer Will Not Start - No Door Lock
Is there voltage Replace the at the input blk wire coming secondary door into the secondary switch assembly. door switch? Correct wiring to the secondary door switch. FLW300S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 51 MOTOR DC OPTOISOLATORS POWER SUPPLY FUS1 TAN/WHT 7 AMP SOFTENER 250 VOLT YEL/BLK LOW VOLTAGE DETERGENT/BLEACH CONTROL LOGIC CIRCUIT MOTOR CONTROL ASSEMBLY FIELD ROTOR TACH MOTOR ASSY FLW301S 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 52: Washer Will Not Start. Control Analysis
Washer Will Not Start. Control Analysis. Is there 120 Volt Refer to the AC across "H6-6" to "H6-5" on Washer Will Not Fill the control board? section. Replace the control board. FLW302S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 53 Section 3 Troubleshooting (NetMaster Models) WASHER WILL NOT START – CONTROL ANALYSIS 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 54: Washer Will Not Fill
AC from the input side of Change the motor the mixing valve to "H1-9" or "H1-3" control board. of the motor control board? Change the mixing valve. FLW304S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 55 MOTOR DC OPTOISOLATORS POWER SUPPLY FUS1 TAN/WHT 7 AMP SOFTENER 250 VOLT YEL/BLK LOW VOLTAGE DETERGENT/BLEACH CONTROL LOGIC CIRCUIT MOTOR CONTROL ASSEMBLY FIELD TACH ROTOR MOTOR ASSY FLW305S 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 56: Washer Overflows
Is there voltage improper wiring across the coil of and replace either the hot or cold inoperative water solenoid? pressure switch if necessary. Replace inoperative water valve. FLW306S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 57 COLD OPTOISOLATORS POWER SUPPLY FUS1 TAN/WHT 7 AMP SOFTENER 250 VOLT YEL/BLK LOW VOLTAGE DETERGENT/BLEACH CONTROL LOGIC CIRCUIT MOTOR CONTROL ASSEMBLY FIELD TACH ROTOR MOTOR ASSY FLW307S 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 58: Pump Does Not Operate
Replace if the motor? necessary. Is there voltage Correct wiring across terminals between control "H6-2" and "H6-5?" and pump. Replace control assembly. FLW308S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 59 MOTOR DC OPTOISOLATORS POWER SUPPLY FUS1 TAN/WHT 7 AMP SOFTENER 250 VOLT YEL/BLK LOW VOLTAGE DETERGENT/BLEACH CONTROL LOGIC CIRCUIT MOTOR CONTROL ASSEMBLY FIELD TACH ROTOR MOTOR ASSY FLW309S 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 60: Door Locked, Motor Does Not Run (E:df On Display)
Does Replace motor the machine control board. run now? Is there Replace continuity? motor. Replace motor control board. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 61 MOTOR DC OPTOISOLATORS POWER SUPPLY FUS1 TAN/WHT 7 AMP SOFTENER 250 VOLT YEL/BLK LOW VOLTAGE DETERGENT/BLEACH CONTROL LOGIC CIRCUIT MOTOR CONTROL ASSEMBLY FIELD TACH ROTOR MOTOR ASSY FLW309S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 62 Section 3 Troubleshooting (NetMaster Models) Notes © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 63: Mdc Models
This error occurs if the pressure switch fails to open in 30 minutes in any fill/agitate cycle. This is a fatal error. 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 64: Coins Ignored When Entered
Replace the Properly reseat Properly reseat coin drop. connection and connection and Replace electronic conduct diagnostic conduct diagnostic control. test again. test again. FLW297S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 65 Section 3 Troubleshooting (MDC Models) Notes 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 66: No Visible Display On Control
"H1-3" control the transformer? transformer. transformer? board? Make sure "H1" Correct wiring connector is between Replace seated properly. transformer and transformer. Replace control. control board. FLW298S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 67 Section 3 Troubleshooting (MDC Models) NO VISIBLE DISPLAY ON CONTROL 801182 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 68: Washer Will Not Start - No Door Lock
Is there voltage Replace the at the input blk wire coming secondary door into the secondary switch assembly. door switch? Correct wiring to the secondary door switch. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 69 Section 3 Troubleshooting (MDC Models) WASHER WILL NOT START – NO DOOR LOCK 801182 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 70: Washer Will Not Start. Control Analysis
Washer Will Not Start. Control Analysis. Is there 120 Volt Refer to the AC across "H6-6" to "H6-5" on Washer Will Not Fill the control board? section. Replace the control board. FLW302S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 71 Section 3 Troubleshooting (MDC Models) WASHER WILL NOT START – CONTROL ANALYSIS 801182 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 72: Washer Will Not Fill
AC from the input side of Change the motor the mixing valve to "H1-9" or "H1-3" control board. of the motor control board? Change the mixing valve. FLW304S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 73 Section 3 Troubleshooting (MDC Models) WASHER WILL NOT FILL 801182 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 74: Washer Overflows
Is there voltage improper wiring across the coil of and replace either the hot or cold inoperative pressure switch water solenoid? if necessary. Replace inoperative water valve. FLW306S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 75 Section 3 Troubleshooting (MDC Models) WASHER OVERFLOWS 801182 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 76: Pump Does Not Operate
Replace if the motor? necessary. Is there voltage Correct wiring across terminals between control "H6-2" and "H6-5?" and pump. Replace control assembly. FLW308S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 77 Section 3 Troubleshooting (MDC Models) PUMP DOES NOT OPERATE 801182 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 78: Door Locked, Motor Does Not Run (E:df On Display)
Does Replace motor the machine control board. run now? Is there Replace continuity? motor. Replace motor control board. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 79 Section 3 Troubleshooting (MDC Models) DOOR LOCKED, MOTOR DOES NOT RUN (E:DF ON DISPLAY) 801182 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 80 Section 3 Troubleshooting (MDC Models) Notes © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 81: Section 4 - Grounding
115 ± 12 other than that V.A.C. V.A.C. illustrated, the qualified electrician should correct the Round 115 ± 12 problem. Grounding V.A.C. Prong H008GE3A Washer Power Cord Figure 21 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 82: Machine Ground Connections - Front Control Washers (Electromechanical Models)
6 Grounding Hardware to Control Cabinet Wrapper 7 Ground to Motor 8 Ground to Electric Drain Pump 9 Ground to Motor Bracket 10 Ground to Outer Tub 11 Ground to Outer Tub Front © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 83 Section 4 Grounding H009GE3A Front Control Washers (Electromechanical Models) Figure 22 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 84: Machine Ground Connections - Rear Control Washers
5 Ground to Lower Rear Access Panel (Netmaster models) 6 Ground to Motor 7 Ground to Electric Drain Pump 8 Ground to Motor Bracket 9 Ground to Outer Tub 10 Ground to Outer Tub Front © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 85 Section 4 Grounding FLW665G Rear Control Washers Figure 23 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 87: Section 5 - Service Procedures
STEP 3 REMOVE CONTROL PANEL OUT OF UNLOCK CONTROL PANEL MOVE TOP OF CONTROL PANEL AWAY FROM CONTROL CABINET AND CONTROL CABINET. LIFT UP. H198SE3A Figure 24 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 88: Control Panel (Electronic Control Models)
NOTE: Refer to wiring diagram when rewiring switch shaft. Refer to Figure 26. light. (3) Remove knurled nut holding switch to control panel. Refer to Figure 26. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 89 By using this static protection device, will not be issued. potential electrostatic discharge problems associated with handling of electronic control will be minimized. Always handle electronic control by 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 90 SPEED LOCKWASHERS SWITCH KNURLED SETSCREW INDICATOR LIGHTS CONTROL PUSH-TO-START KNOB SWITCH ASSEMBLY LOCKWASHER INDICATOR LIGHT CONTROL H070PE3A PANEL FRAME CONTROL PANEL OVERLAY FRONT CONTROL WASHERS Figure 27 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 91 MOTOR SCREW SPEED CONTROL CONTROL SWITCH PANEL SCREW KNOB FRAME ASSEMBLY INDICATOR LIGHTS SETSCREW KNURLED START SWITCH LOCKWASHER CONTROL PANEL OVERLAY REAR CONTROL WASHERS H200SE3A Figure 28 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 92 SEALING WASHER REAR PANEL SCREW SCREW CONTROL HOOD SCREW CONTROL PANEL FRAME PRESSURE SWITCH LOCKWASHER SCREW SCREW LOCKWASHER GRAPHIC PANEL TRANSFORMER H117P ELECTRONIC CONTROL MODELS Figure 29 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 93: Control Panel Overlay (Electromechanical Models)
Using a hair dryer or heat gun to warm the overlay, remove control panel overlay by peeling it from the control panel assembly. NOTE: Control panel overlay has an adhesive backing. 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 94: Control Panel Overlay (Electronic Control Models)
(3) Using a hair dryer or heat gun to warm the overlay, remove control panel overlay by peeling it from the control panel frame. NOTE: Control panel overlay has an adhesive backing. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 95 HOOD CONTROL PANEL SCREW FRAME SCREW SCREW PRESSURE SWITCH END CAP (Left) CARD READER TRANSFORMER SCREW END CAP (Right) GRAPHIC GROUND SCREW PANEL WIRE FLW67P Figure 30 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 96: Cabinet Top
(7) Carefully lift cabinet top off washer and set SCREW SPEED out of the way to prevent damage. SECURITY TOP PANEL SPEED NUTS CONTROL SCREWS CABINET WITH SCREW H044PE1A H201SE1A LOCKWASHER Figure 33 Figure 31 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 97 Refer to Figure 38. Remove clips holding wire harness and door seal hose along top H205SE1A flange of front panel and remove front panel. Figure 36 (continued) 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 98 Refer to Figure 37. Figure 37 Door Door Dispenser Switch Switch Drawer Wires Door Latch Door Switch Latch Switch Attaching Screws Front Panel Wire Attaching Screws H204SE3A Harness Figure 38 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 99 RELAYS TIMER TIMER MOUNTING PRESSURE BRACKET SWITCH CLUTCH CONTROL SHIELD COIN FUNNEL MOTOR CONTROL BOARD SLIDE EXTENSION H124PE3A FRONT CONTROL WASHERS Figure 39 (continued) 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 100 BRACKET INSTRUCTION STICKER RETAINER METER CASE SCREW (Optional METER CASE for added security) GASKET CABINET GASKET BRACKET RETAINER REAR CORNER GUSSET FLW801P REAR CONTROL WASHERS Figure 40 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 101: Pressure Switch
Refer to Figure 41. CABINET REAR HINGES MOTOR WIRE, ROPE CONTROL OR CHAIN BOARD RELAYS PRESSURE MOTOR SWITCH CONTROL BOARD RELAYS H221SE3A FRONT CONTROL WASHERS REAR CONTROL WASHERS Figure 41 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 102: Motor Control Board
Refer to Figure 32. issued. NOTE: To avoid damage to hinges, be sure to support cabinet top with a small chain or something similar. Refer to Figure 32. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 103: Timer Assembly
Lift timer and mounting bracket out of control cabinet or meter case as far as wires permit. Figure 42 NOTE: If replacing clutch only, proceed to Step “f”. (continued) 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 104 Make sure clutch moves freely after setscrew is TIMER BRACKET tightened. TIMER SLOT SPRING SHAFT HOLDING SETSCREW SPRING TLW296S Figure 45 SETSCREW GROOVE CLUTCH H208SE1A Figure 44 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 105: Control Cabinet Front
Refer to Figure 60. hinges. NOTE: To avoid damage to hinges, be sure to support cabinet top with a small chain or something similar. Refer to Figure 32. 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 107 310P4 1/4 inch using screws and carriage bolt previously Ratchet extension Tool, reinstall both removed. locknuts and tighten locknuts firmly. (5) Reconnect coin drop wire harness. 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 108 Figure 48. Square Drive Service Door Switch Meter Locknut Case Locking Front of Meter Case W485SE1D Switch Figure 49 Bracket W408SE1B Figure 48 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 109 Refer to Figure 51. disconnect plugs. NOTE: Multiplier is held inside meter case by two Velcro strips. Service Door Switch Bracket Meter W408SE3A Case Figure 50 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 110 Refer to Figure 52. Back End of Coin Drop Coin Drop Front Face Plate Coin Drawer Housing W410SE3A Figure 52 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 111 Refer to Figure 53. Back End of Coin Drop Coin Drop Front Face Plate Meter Case Coin Drawer Housing Coin-Return Stops W411SE3A Figure 53 (continued) 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 112 Figure 54. opening. Refer to Figure 54. Coin Drop Coin Drop Front Face Plate Service Door Opening Meter Case W412SE3A Figure 54 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 113 Refer to Figure 57. (4) Grasp top of coin drop front face plate between the two drops, as shown in Figure 56. Coin-Return Stops W415SE1A Figure 57 (continued) 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 114: Card Reader
(9) Reconnect wires by referring to the wiring diagram located inside the control hood. (10) Reinstall service door switch and wire harness into meter case bracket. Refer to Figure 50. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 115: Control Cabinet Wrapper
(11) Remove screws holding control cabinet wrapper to top flange of side panels. (12) Carefully lift control cabinet assembly off washer and set out of the way. 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 116 Section 5 Service Procedures CABINET SECURITY TOP PANEL CONTROL CABINET FRONT CONTROL CABINET WRAPPER TABS CONTROL CABINET CONTROL WRAPPER CABINET FRONT TABS H072PE3A Figure 60 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 117: Electric Drain Pump
NOTE: Refer to wiring diagram when rewiring drain pump. d. Remove 3 mounting screws holding pump to base and remove pump out through front of washer. Refer to Figure 61. H210S31A Figure 61 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 118: Belt
Spring is in the (10) Remove shoulder screw from inside meter 6 o’clock position. Refer to Figure 36. case. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 119 Refer to Figure 62. INNER BASKET PULLEY PIVOT BOLT ADJUSTING MOTOR BOLT BELT MOUNTING INCH BRACKET METAL MOTOR SHAFT PIVOT BOLT ADJUSTING WIRE BOLT HARNESS FLW1119S GROUND WIRES Figure 62 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 120: Mixing Valve
Refer to Figure 63, Step “4”. Figure 64. f. Remove wire harness disconnect blocks from mixing valve solenoid terminals. Refer to Figure 64. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 121 STEP 1: Pull seal up. STEP 2: Pull seal out. STEP 3: Pull seal down. STEP 4: Pull seal out and remove. FLW1190B Figure 63 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 122 CLAMP INLET HOSE BACKFLOW PREVENTER CONTROL CABINET WRAPPER SCREWS CONTROL SHIELD MIXING VALVE MIXING VALVE PLATE REAR PANEL MOUNTING CLIP H042PE3A WIRE HARNESS DISCONNECT BLOCKS Figure 64 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 123: Front Panel
“2”), and down (Figure 63, Step “3”). h. When seal releases from lip of front panel, pull out and remove the seal. Refer to Figure 63, Step “4”. (continued) 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 124 CLAMP DOOR LATCH SWITCH HOSE WIRE WIRE HARNESS LARGE CLAMP DOOR SEAL WHEN INSTALLING DOOR SEAL ALIGN CONNECTING HOSE IN VERTICAL POSITION H222SE3A LARGE CLAMP Figure 65 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 125: Loading Door
CHARACTER OF THE MODEL NUMBER Door Figure 66 Glass Screw H212SE1A MODELS WITH LETTER “H” OR “J” IN THE 8TH CHARACTER OF THE MODEL NUMBER Figure 67 (continued) 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 126: Door Seal And Hose Assembly
Refer to Figure 47. NOTE: To avoid damage to spring, use screwdriver on wire clamp ring to right or left of spring. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 127: Door Switch
Open loading door. cabinet front. Refer to Figure 31. b. Carefully remove wire clamp ring from groove with small flat blade screwdriver. Spring is 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 128 Place belt on motor pulley, then carefully run hinges. Refer to Figure 32. belt on inner basket pulley while slowly turning pulley. Refer to Figure 62. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 129: Outer Tub Front Panel
Refer to Figure 38. Remove front panel (with door. Refer to Figure 40. loading door attached) away from washer as far (2) Remove timer bracket cap screws. Refer to as wires permit. Figure 40. 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 130 Remove rubber seal from outer tub front panel ring screw and nut until a spacing of one inch is and discard seal. achieved at the clamp ring opening or until tight. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 131: Inner Basket Pulley
Refer to Figure 62. (2) Pull down on motor to increase belt tension. Use a Burroughs belt gauge to obtain proper tension. Proper belt tension is 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 132: Inner Basket Assembly
Refer to Figure 32. will permit. (5) Remove shoulder screw from inside meter case. Refer to Figure 40. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 133 Remove belt from motor shaft. Left Hand Tap. NOTE: After reinstalling belt, adjust belt tension c. Dip threads of three new tension rods into per Paragraph 65. lightweight oil. 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 134 .05 inch. j. Remove inner basket/trunnion assembly from washer and evenly torque three nuts to 200 ± 10 inch-pounds. k. Recheck that concentricity is still within .05 inch. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 135 Trunnion Shaft Apply grease to this area Bearing Housing Assembly Apply Anti-Seize Outer Compound to These areas FLW1707S Inner Basket Figure 72 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 136 • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the washer is properly grounded. W003 Left Hand Pulley Bolt Thread Tightening Screw Fixture Pulley Flat Washer FLW25K Figure 73 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 137 LOCKWASHER OUTER BOLTS FLAT WASHER INNER BASKET PULLEY INNER BOLTS MOUNTING PLATE PRESSURE HOSE CLIP BEARING HOUSING ASSEMBLY PRESSURE HOSE FRONT CONTROL WASHER H240SE3A ILLUSTRATED Figure 74 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 138: Bearing Housing
Refer to Figure 65. NOTE: To avoid damage to spring, use screwdriver on wire clamp ring to right or left of spring. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 139 Remove cap screw (left hand thread), torque to 150 inch pounds (17.16 Nm). lockwasher and flat washer holding pulley to inner basket shaft. Refer to Figure 74. t. Remove pulley from shaft. 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 140 From front of washer, pull inner basket forward as far as possible. Flat washer should be against pulley. ai. Push inner basket back into outer tub as far as possible. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 141: Section 6 - Adjustments
Refer to MODELS WITH THE LETTER “H” OR “J” IN THE Figure 75. EIGHTH CHARACTER OF THE MODEL NUMBER Figure 75 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 142: Loading Door
MODELS WITH THE LETTER “E” IN THE MODELS WITH THE LETTER “H” OR “J” IN THE EIGHTH CHARACTER OF THE MODEL NUMBER EIGHTH CHARACTER OF THE MODEL NUMBER Figure 76 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 143: Motor Belt Tension
Refer to Figure 77. INNER BASKET PULLEY PIVOT BOLT ADJUSTING MOTOR BOLT BELT MOUNTING INCH BRACKET METAL MOTOR PULLEY PIVOT BOLT ADJUSTING BOLT WIRE HARNESS FLW1119S GROUND WIRES Figure 77 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 144: Door Catch
Reinstall door bezel. Funnel Door Catch 685429 Door Lock Alignment of These Two Edges 685430 Catch H250SE3A SHOWN CLOSED Figure 78 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 145: Shipping Braces
Removal of supports prior to final installation may cause SHOCK ABSORBER SHIPPING SUPPORT SHOCK ABSORBER SHIPPING SUPPORT SHIPPING BRACKET FLW821S Figure 79 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 146: Cleaning Non-Electronic Coin Drop
Refer to Figure 80. Save pin for reinstallation when cleaning is complete. f. Move metal clip closer to sensor so that it comes off frame. Refer to Refer to Figure 80. DRY5B Figure 82 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 147: Cleaning Electronic Coin Drop
NOTE: The electronic coin drop should be cleaned once a year. Clean the drop more often if it is exposed to high levels of residue or lint build-up. 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 148 Coin Drops with New-Style Spring (refer to Refer to Figure 87): Catch Spring DRY2088N Figure 85 DRY2404N DRY2404N Figure 87 (3) Open cover of coin drop. Refer to Refer to Figure 88. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 149 Refer to Refer to Figure 89 or Refer to Figure 90. Alcohol Moistened Cloth DRY2406N Figure 91 Old-Style Spring Coin Drop DRY2090N DRY2090N Figure 89 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 150 Reconnect electrical power to machine and drop. k. Add a coin to drop to verify that coin drop is operating properly and that electrical connection is working properly. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 151: Section 7 - Wiring Diagrams
W030 WIRING DIAGRAMS AND SCHEMATICS FOUND ON THE FOLLOWING PAGES ARE FOR MODELS COVERED IN THIS MANUAL. 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 152: Schematic
W030 SCHEMATIC MODELS HWF261*E, HWR261*E, SWF261*E, SWR261*E, HWF261*H, HWR261*H, SWF261*H AND SWR261*H THROUGH SERIAL NUMBER 0007013011 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 153: Models Hwf261*H, Hwr261*H, Swf261*H And Swf261*Hstarting Serial Number 0007013012
Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 SCHEMATIC MODELS HWF261*H, HWR261*H, SWF261*H AND SWF261*H STARTING SERIAL NUMBER 0007013012 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 154: Models Hwrb61*J1102, Swrb61*H, Swrb61*J, Swrc61*J, Swrd61*H, Swrf61*J And Swrh61*J
Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 SCHEMATIC MODELS HWRB61*J1102, SWRB61*H, SWRB61*J, SWRC61*J, SWRD61*H, SWRF61*J AND SWRH61*J © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 155: Models Hwrt61*H, Hwrt61*H1102, Hwry61*H1102, Hwrz61*H, Hwrz61*H1102, Swrt61*H, Swry61*H And Swrz61*H
Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 SCHEMATIC MODELS HWRT61*H, HWRT61*H1102, HWRY61*H1102, HWRZ61*H, HWRZ61*H1102, SWRT61*H, SWRY61*H AND SWRZ61*H 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 156: Connection Diagram Models Hwf261*E, Hwf261*H, Swf261*E And Swf261*H
Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 CONNECTION DIAGRAM MODELS HWF261*E, HWF261*H, SWF261*E AND SWF261*H © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 157: Models Hwr261*E, Hwr261*H, Swr261*E And Swr261*H
Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 CONNECTION DIAGRAM MODELS HWR261*E, HWR261*H, SWR261*E AND SWR261*H 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Page 158: Models Hwrb61*J1102, Swrb61*H, Swrb61*J, Swrc61*J, Swrd61*H, Swrf61*J And Swrh61*J
Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 CONNECTION DIAGRAM MODELS HWRB61*J1102, SWRB61*H, SWRB61*J, SWRC61*J, SWRD61*H, SWRF61*J AND SWRH61*J © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 800383...
Page 159: Models Hwrt61*H, Hwrt61*H1102, Hwry61*H1102, Hwrz61*H, Hwrz61*H1102, Swrt61*H, Swry61*H And Swrz61*H
Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 CONNECTION DIAGRAM MODELS HWRT61*H, HWRT61*H1102, HWRY61*H1102, HWRZ61*H, HWRZ61*H1102, SWRT61*H, SWRY61*H AND SWRZ61*H 800383 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

This manual is also suitable for:

Hwf261*h Swf261*e Swf261*h Hwr261*e Hwr261*h Hwrb61*j1102 ... Show all

Alliance Laundry Systems HWF261*E Service Manual

Section 1 - Safety Information

Section 2 - Introduction

Section 3 - Troubleshooting

1 Troubleshooting Coin Drop

2 No Spin Condition - Models through Serial No. 9811005967

3 Troubleshooting Knocking Noise

4 No Motor Rotation, or Drive Failure Code "E:DF" on Electronic Display Units

Electromechanical Models

5 Start up

6 Start and Door Lock

7 Fill Sequence

8 Volt Control

9 Volt Motor Power

10 Timer Chart

11 Cycle Timer Motor Control Inputs

12 Cycle Timer Water Fill Input Logic

14 Control System Faults

15 No Start on Coin Slide Front Control Washers

Netmaster Models

16 Microwand Does Not Communicate with Control

17 Coins Ignored When Entered

18 No Visible Display on Control

19 Washer will Not Start - no Door Lock

20 Washer will Not Start. Control Analysis

21 Washer will Not Fill

22 Washer Overflows

23 Pump Does Not Operate

24 Door Locked, Motor Does Not Run (E:df on Display)

MDC Models

25 Error Code Listing

26 Coins Ignored When Entered

27 No Visible Display on Control

28 Washer will Not Start - no Door Lock

29 Washer will Not Start. Control Analysis

30 Washer will Not Fill

31 Washer Overflows

32 Pump Does Not Operate

33 Door Locked, Motor Does Not Run (E:df on Display)

Section 4 - Grounding

34 Wall Receptacle Polarity Check

35 Machine Ground Connections - Front Control Washers (Electromechanical Models)

36 Machine Ground Connections - Rear Control Washers

Section 5 - Service Procedures

37 Control Panel (Electromechanical Models)

38 Control Panel (Electronic Control Models)

39 Control Panel Overlay (Electromechanical Models)

40 Control Panel Overlay (Electronic Control Models)

41 Cabinet Top

42 Pressure Switch

43 Motor Control Board

44 Timer Assembly

45 Control Cabinet Front

46 Coin Drop

47 Card Reader

48 Control Cabinet Wrapper

49 Relay

50 Electric Drain Pump

51 Belt

52 Mixing Valve

53 Front Panel

54 Loading Door

55 Door Seal and Hose Assembly

56 Door Switch

57 Door Latch Switch

58 Motor

59 Outer Tub Front Panel

60 Inner Basket Pulley

61 Inner Basket Assembly

62 Bearing Housing

Section 6 - Adjustments

63 Cabinet Leveling Legs

64 Loading Door

65 Motor Belt Tension

66 Door Catch

67 Shipping Braces

68 Cleaning Non-Electronic Coin Drop

69 Cleaning Electronic Coin Drop

Section 7 - Wiring Diagrams

Schematic

Connection Diagram Models HWF261E, HWF261H, SWF261E and SWF261H