Advertisement
Quick Links
Amplifier
Amplifier
Installation
stallatio
stallat
Guide
Contents:
Guarantee and Warranty · · · · · · · · · · · · · · · · · · · · · · · ·
How it Works · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 2
Before Getting Started · · · · · · · · · · · · · · · · · · · · · · · · · · 3
Installing a Wilson Outside Antenna · · · · · · · · · · · · · · ·
Installing the Low-Profi le Antenna · · · · · · · · · · · · · · · · ·
Warnings and Recommendations · · · · · · · · · · · · · · · · ·
Understanding the Amplifi er Lights · · · · · · · · · · · · · · · · · 9
About Wilson Electronics · · · · · · · · · · · · · · · · · · · · · · · · 10
Amplifi er Specifi cations · · · · · · · · · · · · · · · · · · Back Cover
Mobile Wireless
iDEN
Amplifi er
!
Warning: This manual contains
important safety and operating information.
Please read and follow the instructions
in this manual. Failure to do so could be
hazardous and result in damage to your
amplifi er.
1
4
6
8
Wilson
®
Electronics, Inc.
Advertisement
Summary of Contents for Wilson Electronics iDEN
-
Page 1: Table Of Contents
Understanding the Amplifi er Lights · · · · · · · · · · · · · · · · · 9 About Wilson Electronics · · · · · · · · · · · · · · · · · · · · · · · · 10 Amplifi... - Page 2 Returned Material Authorization (RMA) number supplied by Wilson Electronics. Wilson shall, at its option, either repair or replace the product. Wilson Electronics will pay for delivery of the repaired or replaced product back to the original consumer.
-
Page 3: How It Works
Wilson Electronics manufactures a wide variety of antennas to help you customize your amplifi er for your specifi c application. Several are shown below. See your dealer or visit www.wilsonelectronics.com. - Page 4 Before Getting Started This guide will help you properly install Wilson’s single-band, mobile wireless amplifi er. It is important to read through all of the installation steps for your particular application prior to installing any equipment. Read through the instructions, visualize where all the equipment will need to be installed and do a soft installation before mounting any equipment.
-
Page 5: Installing A Wilson Outside Antenna
Installing a Wilson Outside Antenna To receive the best cell signal, select a location in the center of the vehicle’s roof at least 12 inches away from any other antennas and free of obstructions. Follow the specifi c antenna installation instructions included with the outside antenna (sold separately). - Page 6 Installing a Wilson Amplifi er Warning: Do not plug in the DC power supply until the outside and inside antenna cables are attached to the amplifi er. Select a location to install the amplifi er that is away from excessive heat, direct sunlight or moisture and that has proper ventilation.
-
Page 7: Installing The Low-Profi Le Antenna
Installing the Low-Profi le Antenna Install the low-profi le inside antenna 8-12 inches from where the cell phone or cellular data card will be used. Low-profi le Antenna Warning: Do not install the low-profi le Amplifi er antenna within four inches of metal. (Metal found inside the vehicle’s seat will not affect the antenna’s performance.) Place the inside antenna on the side of the... - Page 8 Powering up a Wilson Amplifi er Make sure both the outside and inside antenna cables are connected before powering up the amplifi er. Connect the DC plug-in power supply cable to the amplifi er marked “Power” and insert the large end into DC power socket (the cigarette lighter outlet.) Warning: Use only the power Carefully insert the power cable.
-
Page 9: Warnings And Recommendations
Warnings and Recommendations Warning: In a wireless installation, do not plug the amplifi er directly into the cell phone or cellular data card using an antenna adapter. It will damage the amplifi er, the cell phone or the cellular data card. Warning: Do not install the inside antenna within four inches of metal. -
Page 10: Understanding The Amplifi Er Lights
Understanding the Amplifi er Lights Power Indicator Light (located on the side) Signal Indicator Light (located on the back) Power Indicator Light Shows green when the unit is turned on. Signal Indicator Light If the amplifi er is powered up and the light is off, this indicates the unit is working properly. -
Page 11: About Wilson Electronics
About Wilson Electronics Wilson Electronics, Inc. has been a leader in the wireless communications industry for 40 years. The company designs and manufactures amplifi ers, antennas and related components that signifi cantly improve cellular telephone signal reception and transmission in a wide variety of applications, both mobile and in-building. -
Page 12: Amplifi Er Specifi Cations
Amplifi er Specifi cations Part Number 804002 Frequency 806-866 MHz Gain (Rx/Tx) 40 dB / 40 dB Max Output Power 3 watts Max RF (up/down) +35 dBm / +10 dBm Noise Figure 4 dB nominal Flatness (up/down) ± 3 dB / ± 3 dB Isolation >...
Need help?
Do you have a question about the iDEN and is the answer not in the manual?
Questions and answers