Set-Up; Operation; Maintenance; Troubleshooting - Fellowes P70CM User Manual

Set-Up

For safety reasons, this model will operate only if the shredder head is in the correct position
on the basket. Align slot on the side of the shredder head (A) with tab on the side of the
basket (B) and place it onto the basket in this position.

Operation

For convenience, your shredder is equipped with an automatic-start sensor (C). This
means that when the control switch (D) is on automatic [I] position, the shredder will start run-
ning when you put paper into it and stop 1 or 2 seconds after the paper has passed through.
Because the sensor cannot tell the difference between paper and other objects, this feature
can also be a hazard, especially to children and pets. To avoid accidents, turn off the
shredder as soon as you are finished. Unplug shredder if it will not be used for an extended
period.
To shred
• Plug in shredder with control switch (D) in off [O] position.
• Slide control switch to automatic [I] position to signal readiness.
• Feed paper straight into entry (E), until the shredder automatically begins shredding; see
Product Profile for limits on paper width, shreddable items, sheet capacity, etc.
• Shred for no more than 2 minutes; shredding longer will cause shredder to turn itself off for
4 minutes to cool down.
• Slide control switch to off [O] position after cutting has stopped. Cutting continues for 1-2
seconds after paper has gone through in order to clear shredded paper from cutting
cylinders.
In case of a paper jam, which may occur if the shredder is pushed beyond its specified
capabilities, press the control switch to the off [O] position and empty the basket if full. Then:
1) Slide and hold control switch in reverse [R] position and attempt to back paper out of
shredder.
2) If shredder jams in reverse mode, slide control switch to automatic [I] position and attempt
to continue shredding operation.
3) If shredder jams again, alternate control switch slowly between reverse [R] and automatic
[I] positions to attempt to move jammed paper completely through shredder.
If you are unable to clear the jam using this method, turn off and unplug the shredder; remove
shredder head from the wastebasket and carefully remove any paper extending below the
cutting cylinders; empty the wastebasket; reassemble the shredder and repeat jam clearing
procedure.
4

Maintenance

Regular emptying of the basket is important to ensure the smooth operation of the
cutting cylinders. If paper is within 2 inches of shredder head, turn off and unplug the
shredder, remove the shredder head and empty the basket.
Regular oiling of the shredder is also necessary to ensure proper performance.
If you are running the shredder at or near capacity, we recommend oiling it monthly .
Using Fellowes Powershred Lubricant #35250 or other non-aerosol vegetable-based
oil in a long-nozzle container:
• Apply oil over full width of paper entry (1) with shredder in off [O] position.
• Press control switch to automatic [I] position which will cause shredder to run for about 2
seconds.
• Press and hold control switch in reverse [R] position for 3-5 seconds.
• Repeat above automatic [I] and reverse [R] sequence three times.
REMINDER: Do not use flammable synthetic oil, petroleum-based products or aerosol
lubricants of any kind in or near the shredder at any time.

Troubleshooting

If you have a problem with your shredder, check the symptoms and remedies below. If you
cannot solve the problem this way, contact Fellowes Customer Service. Do not open
shredder head to attempt repair: It could expose you to serious electric shock and will
void your warranty.
Symptom
Shredder does not start or stops while shred-
ding.
Shredder squeaks, grinds or runs below
capacity.
Shredder continues to run for 1 or 2
seconds after shredding has been
completed.
Remedy
• Make sure shredder is plugged in and
switch is in automatic [I] position.
• If paper appears to be jammed. Follow
instructions under Operation .
• Check shredder head position. Follow
instructions under Set-Up .
• Wait 4 minutes for shredder to cool down
before trying again.
Check to see if basket is full. Oil cutting
cylinders. Follow instructions under
Maintenance.
No action required. This is a self-cleaning
function.
5