BodyCraft 6900-LP Instruction Manual

Leg press option for strata strength training system

Hide thumbs

Table Of Contents

INSTRUCTION MANUAL

LEG PRESS OPTION FOR STRATA STRENGTH

TRAINING SYSTEM

QUESTION?

As a quality home gym supplier we are committed to your complete satisfaction. If you have

questions, or find missing or damaged parts, we will guarantee your complete satisfaction through

our authorized dealer service centers or our home office customer service department. Please call

your local dealer for assistance or BodyCraft at 800-990-5556 (9:00 AM - 5:00 PM). Our trained

technicians will provide immediate assistance to you, free of charge.

Bodycraft is a division of Recreation Supply Inc.

P.O. BOX 181

Sunbury, OH 43074

6900-LP

Table of Contents

Need help?

Do you have a question about the 6900-LP and is the answer not in the manual?

Questions and answers

Summary of Contents for BodyCraft 6900-LP

Page 1 Please call your local dealer for assistance or BodyCraft at 800-990-5556 (9:00 AM - 5:00 PM). Our trained technicians will provide immediate assistance to you, free of charge.
Page 2 PARTS LIST PARTS LIST DESCRIPTION QTY. BASE CONNECTION FRONT BASE LEG PRESS SUPPORT REAR TUBE SLIDING SEAT SUPPORT FRAME SEAT SUPPORT SLIDING TUBE FOOT REST STEEL ROLLER HANDLE BAR SINGLE PULLEY BRACKET 50 ID. SQUA. END CAP 50 SQUA. END CAP RUBBER STOP RUBBER BUMPER NON-SKID PAD...
Page 3 PARTS CHART PARTS CHART REAR TUBE(204) BASE FRONT SEAT SUPPORT(206) CONNECTION(201) BASE(202) SLIDING SEAT SUPPORT FRAME(205) SLIDING TUBE(207) STEEL SINGLE PULLEY BRACKET(211) ROLLER(209) LEG PRESS SUPPORT(203) HANDLE BAR(210) FOOT REST(208) 3/4" STEEL 1/2" STEEL RUBBER HOOK(235) BUSHING(218) BUSHING(219) STOP(214) 1" x 130 HAND GRIP(239) SEAT(237) BACK PAD(238)
Page 4 1.Attach BASE CONNECTION(201) and FRONT BASE(202) to the holes in the LEFT WEIGHT BASE of Bodycraft Strata home gym using two 1/2" x 3-1/8" HEX HEAD BOLT(222), four 1/2" WASHER(229) and two 1/2" NYLON NUT(232). 2.Attach LEG PRESS SUPPORT(203) to FRONT BASE(202) using two 3/8" x 3"...
Page 5 STEP2 To ensure best performance, lubricate all pivot points during assembly. Insert two 3/4" STEEL BUSHING(218) and four 1/2" STEEL BUSHING(219) to SLIDING SEAT SUPPORT FRAME(205). Attach SLIDING SEAT SUPPORT FRAME(205) to LEG PRESS SUPPORT(203) as shown using two STEEL ROLLER(209) as shown. Tighten 5/16"...
Page 6 STEP3 Attach HANDLE BAR(210) and SEAT(237) to SEAT SUPPORT(206) as shown using two 3/8" X 1" HEX HEAD BOLT(226) and two 3/8" WASHER(231). Attach BACK PAD(238) on SEAT SUPPORT(206) as shown using two 3/8" x 2-1/2" HEX HEAD BOLT(224) and two WASHER(SMALL)(231). CHECK that all the parts are in assembled correctly as drawing then tighten all bolts.
Page 7 LEG PRESS CABLE LEG PRESS CABLE(234) If previously installed, completely remove TOP CABLE(84), along with pulleys T1, T2, T3, T4 and T5. Remove the two bolts and attach the TOP BEAM into the FRONT UPRIGHT. Assemble TOP CABLE(84A) (from leg press box) and pulleys simultaneously. Insert threaded end of TOP CABLE(84A) into slot in front of TOP BEAM, over pulleys T1, T2, around pulley T3, and over T4.
Page 8 Screw thread end of LEG PRESS CABLE(234) into SINGLE PULLEY BRACKET(211). Attach pulleys G2 and G3, making certain LEG PRESS CABLE(234) runs beneath pulleys and is scated in pulley grooves. Attach the eyelet cable end to ADJUSTMENT TUBE(207) as shown. G2,G3 201,202...