1. Manuals
  2. Brands
  3. Unverferth Manuals
  4. Scales
  5. UM410
  6. Installation and parts

Unverferth UM410 Installation And Parts

Digi-star scales
Hide thumbs
Table of Contents

Advertisement

Quick Links

Grain
Handling
Digi-Star Scales
Installation and Parts
Models UM410 & UM520
Scale Serial #40000 and Higher
Part No. 266900

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the UM410 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Unverferth UM410

  • Page 1 Grain Handling Digi-Star Scales Installation and Parts Models UM410 & UM520 Scale Serial #40000 and Higher Part No. 266900...
  • Page 2 — Introduction Scales - Models 410 and 520 Foreword This symbol identifies important safety messages. When you see it, read the message that follows and be alert to the possibility of personal injury. Remember, safety instructions stated in this manual are for your protection. Read them care fully and follow them closely when working around or using this machine.
  • Page 3 The information, specifications, and illustrations in the manual are based on information available at the time it was written. Due to continuing improvements in the design and manufacture of Unverferth products, all specifications and information contained herein are subject to change without notice.

  • Page 4: Table Of Contents

    — Introduction Scales - Models 410 and 520 Table of Contents Section I Safety General Hazard Information ......................1-2 Following Safety Instructions ......................1-3 Before Servicing ..........................1-3 Before Operating ..........................1-3 During Operation ..........................1-4 Preparing for Emergencies......................1-4 Wearing Protective Equipment ......................
  • Page 5 Operation & Maintenance Wheel, Hub and Spindle Disassembly and Assembly ..............3-2 Scale Calibration and Set Up Number Charts UM410 & UM520 ..........3-4 Scale Calibration and Set Up UM410 .................... 3-9 Scale Calibration and Set Up UM520 .................... 3-12 Downloader Module (Optional) ......................
  • Page 6 — Introduction Scales - Models 410 and 520 Table of Contents Section IV Parts SCALE PACKAGE PARTS 3-Point Scales Spindles ......................4-6 Single Tires with 3-Point Scales Compression Cells .............. 4-14 Walking Tandem/Steerable Tandems/In-Line Tandems 5-Point Scales ........4-18 Tracks with 5-Point Scales ...................... 4-22 Single Tires 5-Point Scales .....................
  • Page 7 — Safety Scales - Models 410 and 520 Section I Safety General Hazard Information ......................1-2 Following Safety Instructions ......................1-3 Before Servicing ..........................1-3 Before Operating ..........................1-3 During Operation ..........................1-4 Preparing for Emergencies......................1-4 Wearing Protective Equipment ......................1-4...

  • Page 8: Safety

    It is true that the designer, the manufacturer, and the safety engineer can help; and they will help, but their combined efforts can be wiped out by a single careless act of the operator. It is said that, “the best kind of a safety device is a careful operator.” We, at Unverferth Mfg. Co., Inc.

  • Page 9: Following Safety Instructions

    — Safety Scales - Models 410 and 520 Following Safety Instructions Read and understand this operator’s manual before operating. • • All machinery should be operated only by trained and authorized personnel. • To prevent machine damage, use only attachments and service parts approved by the manu- facturer.

  • Page 10: During Operation

    — Safety Scales - Models 410 and 520 During Operation • Regulate speed to field conditions. Maintain complete control at all times. • Never service or lubricate equipment when in operation. • Keep away from overhead power lines. Electrical shock can cause serious injury or death. •...

  • Page 11: Set Up

    — Set Up Scales - Models 410 and 520 Section II Set Up General Set Up Instructions ....................... 2-3 Scale Kit Installation J-Block Installation - All Models ..................2-4 Scale Indicator Installation - All Models ................2-5 3-Point Scales with Spindles ....................2-6 Hitch Assembly ......................
  • Page 12 Brent Models: 782, 882, 1082, 1182, 1186, 1282, 1386, V700, V800, V1000, V1100, V1300, V1500 Unverferth Models: 760, 860, 1015, 1017, 1019, 1050, 1060, 1115, 1117, 1119, 1160, 1315, 1317, 1319, 1519, 7250, 8250, 9250 Killbros Models: 735, 835, 1035, 1135...

  • Page 13: General Set Up Instructions

    — Set Up Scales - Models 410 and 520 General Set Up Instructions • TIPPING OR MOVEMENT OF THE MACHINE CAN CAUSE SERIOUS INJURY OR DEATH. BE SURE MACHINE IS SECURELY BLOCKED. • FALLING OBJECTS CAN CAUSE SERIOUS INJURY OR DEATH. DO NOT WORK UNDER THE MACHINE AT ANY TIME WHILE BEING HOISTED.

  • Page 14: Scale Kit Installation

    — Set Up Scales - Models 410 and 520 Scale Kit Installation J-Block Installation - All Models 1. Attach the J-Block to the left vertical face of Cable 50’ the cart using the #8 hardware. J-Block (9006047) (9004925) NOTE: Facing the J-Block to the inside of the cart will protect the scale wire ends.

  • Page 15: Scale Indicator Installation - All Models

    — Set Up Scales - Models 410 and 520 Scale Kit Installation Scale Indicator Installation - All Models 1. Using the bracket provided, locate the scale indicator inside the tractor cab. NOTE: For additional mounting flexibility, optional RAM mount kit (9005936) is available. 5 1/4 REF 2 31/32 REF...

  • Page 16: Hitch Assembly

    — Set Up Scales - Models 410 and 520 Scale Kit Installation — 3-Point Scales with Spindles IF SPINDLE HAS 2 HOLES, USE MOUNTING HOLE FARTHEST AWAY FROM THE HUB. FIG. 2-1 Hitch Assembly 1. Remove the capscrew, lock washer, and nut to remove the standard hitch. Remove the original bushing.
  • Page 17 1282 with Single Wheel/Tires Replace Standard Hitch with Scale Hitch Weigh Bar 3 3/4” Dia. (9004913) (Serial Number B31290099 - Lower) Unverferth Models: 5225, 6225, 7250, 8250 Replace Standard Hitch with Scale Hitch Weigh Bar 2 1/2” Dia. (9004902) with Single Wheel/Tires 7250, 8250 With Dual Wheel/Tires Replace Standard Hitch with Scale Hitch Weigh Bar 2 1/2”...

  • Page 18: Axle Load Cell Installation

    739, 839, 842 10,000 Lbs. 1282 22,000 Lbs. 1039, 1042, 1048, 1139, 1142 14,000 Lbs. 1394 24,000 Lbs. 1152 16,000 Lbs. Unverferth Models: 1352 24,000 Lbs. 5225, 6225 7,000 Lbs. 760, 7250 9,000 Lbs. 860, 8250 10,000 Lbs. 1060, 1160, 9250 14,000 Lbs.

  • Page 19: Hitch Assembly

    (Serial Number B31270099 - Lower) 1194 with Tracks Manual Tension Replace Standard Hitch with Scale Hitch Weigh Bar 3 3/4” Dia. (9004910) Unverferth Models: 9250 with Tracks Manual Tension Replace Standard Hitch with Scale Hitch Weigh Bar 2 7/8” Dia. (9004903) 1110 with Tracks Manual Tension Replace Standard Hitch with Scale Hitch Weigh Bar 3 3/4”...

  • Page 20: Axle Load Cell Installation

    — Set Up Scales - Models 410 and 520 Scale Kit Installation — 3-Point Scales with Compression Cells (continued) Axle Load Cell Installation • BEFORE PROCEEDING, REFER “GENERAL SET UP” PAGE 2-3 FOR PROPER WARNINGS. SAFE LIFTING DEVICE WEIGHT Brent Models: 780, 782 9,000 Lbs.
  • Page 21 — Set Up Scales - Models 410 and 520 Scale Kit Installation — 3-Point Scales with Compression Cells (continued) Axle Load Cell Installation (continued) 5. Remove spacer bars. Assemble anti-rotate brackets to top of scale load cells. figure 2-4. Bracket holes on left-hand and right-hand load cells to be positioned toward cart center line with bracket retaining ring UP.

  • Page 22: Axle Load Cell And Riser Installation

    — Set Up Scales - Models 410 and 520 Scale Kit Installation — 3-Point Scales with Compression Cells (continued) Axle Load Cell and Riser Installation • BEFORE PROCEEDING, REFER “GENERAL SET UP” PAGE 2-3 FOR PROPER WARNINGS. SAFE LIFTING DEVICE WEIGHT Brent Models: 780, 782 9,000 Lbs.
  • Page 23 — Set Up Scales - Models 410 and 520 Scale Kit Installation — 3-Point Scales with Compression Cells (continued) Axle Load Cell and Riser Installation (continued) 6. Assemble Anti-rotate bracket to load cell, see figures 2-11 & 2-12. 7. Orient compression cells so that the lead cables face rear of cart.
  • Page 24 — Set Up Scales - Models 410 and 520 Scale Kit Installation — 5-Point Scales Walking Tandem Walking Tandem Shown Serial Number Decal Facing UP Existing Hub and Wheel Use Existing Hardware If spindle has 2 holes, use mounting hole closest to the hub.
  • Page 25 — Set Up Scales - Models 410 and 520 Scale Kit Installation — 5-Point Scales Steerable Tandems Steerable Tandem Shown Serial Number On Top Use Existing Hardware Use Existing Hardware Position With Decal On Position With Top, Bending Direction Decal On Top Arrow Pointing Up Hitch Casting...
  • Page 26 — Set Up Scales - Models 410 and 520 Scale Kit Installation — 5-Point Scales In-Line Tandems In-Line Tandem Shown Position With Decal On Bottom, Bending Direction Arrow Pointing Down CAT 5 CAT 4 FIG. 2-16 2-16...

  • Page 27: Hitch Assembly

    1194, 1196, 1282, 1394, 1396 Replace Standard Hitch with Scale Hitch Weigh Bar 3 3/4” Dia. (9004910) with Walking Tandem Unverferth Models: 860, 1015, 1050, 1060, 1110, 1115, 1117, 1119, 1120, 1320, 1160, 1310, Replace Standard Hitch with Scale Hitch Weigh Bar 3 3/4” Dia. (9004910)

  • Page 28: Axle Load Cell Installation

    1113 20,000 Lbs. 1282, 1394, 1396 24,000 Lbs. 1111, 1311 22,000 Lbs. 1594, 1596, 2096 28,000 Lbs. 1313 24,000 Lbs. Unverferth Models: Parker Models: 1110, 1119 16,000 Lbs. 1152 16,000 Lbs. 1019, 1115, 1117, 1120 20,000 Lbs. 1154 20,000 Lbs.

  • Page 29: Layout For Models With Track

    — Set Up Scales - Models 410 and 520 Scale Kit Installation — 5-Point Scales Tracks Layout for Models with Tracks Bending direction arrow pointing UP Serial Number decal facing UP All Models Except Model 1082 Axle 9390-187 9405-118 9404-041 Scale Bar 282876 91192...

  • Page 30: Hitch Assembly

    Replace Standard Hitch with Scale Hitch Weigh Bar 3 3/4” Dia. (9004910) V800, V1000, V1100, V1300, V1500 with Tracks Unverferth Models: 860, 1015, 1017, 1019, 1050, 1060, 1110, 1115, 1117, 1119, 1160, 1310, Replace Standard Hitch with Scale Hitch Weigh Bar 3 3/4” Dia. (9004910)

  • Page 31: Axle Load Cell Installation

    30,000 Lbs. V1300 34,000 Lbs. Parker Models: 2096 38,000 Lbs. 18,000 Lbs. V1500 44,000 Lbs. 1042 20,000 Lbs. Unverferth Models: 1142, 22,000 Lbs. 18,000 Lbs. 1048 20,000 Lbs. 1015, 1017, 1050, 1060, 1348 28,000 Lbs. 20,000 Lbs. 1160 1139, 1154, 1354 26,000 Lbs.
  • Page 32 — Set Up Scales - Models 410 and 520 Scale Kit Installation — 5-Point Scales (continued) Single Tires Bending direction arrow pointing UP Serial Number decal facing UP FIG. 2-18 USE EXISTING HARDWARE Bending direction arrow pointing DOWN Serial Number decal facing DOWN 2-22...

  • Page 33: Hitch Assembly

    1182, 1186, 1196, 1282, 1386, 1396, Replace Standard Hitch with Scale Hitch Weigh Bar 3 3/4” Dia. (9004910) V1000, V1100, V1300 Unverferth Models: 760, 860, 1015, 1017, 1019, 1050, 1060, 1110, 1115, 1117, 1119, 1120, Replace Standard Hitch with Scale Hitch Weigh Bar 3 3/4” Dia. (9004910)

  • Page 34: Axle Load Cell Installation

    20,000 Lbs. 1313 24,000 Lbs. 1282 22,000 Lbs. Parker Models: 1396 24,000 Lbs. 1042, 1142, 1139 14,000 Lbs. Unverferth Models: 1348, 1154 20,000 Lbs. 9,000 Lbs. 1354 24,000 Lbs. 10,000 Lbs. 1050, 1060, 1160 14,000 Lbs. 1015, 1017, 1110, 1115, 16,000 Lbs.

  • Page 35: Power Connection

    — Set Up Scales - Models 410 and 520 Scale Kit Installation (continued) Power Connection The power cable should be connected directly to a vehicle battery or key switch supply. The scale end of the power cable is attached to the Power connector located on the bottom panel of the scale.

  • Page 36: Load Cell Connection

    — Set Up Scales - Models 410 and 520 Scale Kit Installation (continued) Load Cell Connection The indicator will normally be supplied with a “J-BLOCK” cable going between the scale and the load cell indicator. Extension Kits are available from your dealer in various lengths. NOTE: If connecting to load cells other than those that were provided with your unit, the indica- tor must be calibrated.

  • Page 37: Set Up

    — Set Up Scales - Models 410 and 520 Routing Scale Cables - Models with Walking Tandems 1. Route the spindle cables through the walking tandem frame as shown in figure 2-19 and Shown less tire for figure 2-20. illustration purposes only. FIG.
  • Page 38 — Set Up Scales - Models 410 and 520 Routing Scale Cables (continued) - Models with Walking Tandems 2. Secure the cables to the top of the walking tandem using the bracket 268675G or 268675R. FIG. 2-21 3. Route cables down the walking tandem and secure using bracket 268674G or 268674R.
  • Page 39 — Set Up Scales - Models 410 and 520 Routing Scale Cables (continued) - Models with Walking Tandems 4. Attach the cables to the tabs on the frame with cable ties. FIG. 2-24 5. Route the right-hand spindle cables from the walking tandem frame along the frame as FIG.

  • Page 40: Rotational Sensor Mounting Instructions - Um520 Auto-Log Scale Single-Auger Grain Carts

    782, 882, 1082, 1182, 1186, 1282, 1386, V700, 735, 835, 1035, 1135, 1175, 1185, 1195 V800, V1000, V1100, V1300, V1500 Parker Models: Unverferth Models: 739, 742, 839, 842, 1039, 1042, 1142 760, 860, 1015, 1017, 1019, 1050, 1060, 1115, 1117, 1119, 1160, 1315, 1317, 1319, 1519, 7250, 8250, 9250 1.

  • Page 41: Rotational Sensor Mounting Instructions - Um520 Auto-Log Scale Single-Auger Grain Carts

    — Set Up Scales - Models 410 and 520 Rotational Sensor Mounting Instructions (continued) UM520 Auto-Log Scale — Single-Auger Grain Cart 4. Place the stainless steel hose clamp (900571) over the shaft and loosely tighten. The clamp BRACKETS may need to be moved again once the sensor (252198B &...
  • Page 42 — Set Up Scales - Models 410 and 520 Rotational Sensor Mounting Instructions (continued) UM520 Auto-Log Scale — Single-Auger Grain Cart UM520 SCALE INDICATOR TO POWER (9005981) SOURCE J-BLOCK CABLE EXTENSION - 10’ (92453) AUTO-LOG Y-CABLE (9006132) EZ-MATE DATA CABLE - 50’ (9006047) PROXIMITY SENSOR EXTENSION CABLE - 16’...

  • Page 43: Serial Number B34930099 And Lower

    DOUBLE-AUGER GRAIN CART MODELS Brent Models: 1194, 1196, 1394, 1396, 1594, 1596, 2096 Unverferth Models: 1110, 1310 Park the empty unit on a firm, level surface. Block the wheels on the machine to keep it from moving. Set the vehicle parking brake, shut off the engine and remove the ignition key from the towing vehicle.
  • Page 44 — Set Up Scales - Models 410 and 520 Rotational Sensor Mounting Instructions UM520 Auto-Log Scale (Optional) — Double-Auger Grain Cart For Serial Number B34930099 and Lower 4. Attach proximity sensor (9006076) to the bracket (281894B), allowing sufficient clearance FLAT BRACKET (1/8”...

  • Page 45: Serial Number B34930100 And Higher

    UM520 Auto-Log Scale — Double-Auger Grain Cart For Serial Number B34930100 and Higher DOUBLE-AUGER GRAIN CART MODELS Brent Models: 1196, 1396, 1596, 2096 Unverferth Models: 1110, 1310, 1610, 1120, 1320, 1620, 2020 Parker Models: 1154, 1354, 1654 Killbros Models: 1113, 1313, 1613 Park the empty unit on a firm, level surface.
  • Page 46 — Set Up Scales - Models 410 and 520 Rotational Sensor Mounting Instructions (continued) UM520 Auto-Log Scale — Double-Auger Grain Cart For Serial Number B34930100 and Higher 4. Attach proximity sensor (9006076) to bracket, allowing sufficient clearance (1/8” to 1/4”) for FIG.

  • Page 47: Operation & Maintenance

    Operation & Maintenance Wheel, Hub and Spindle Disassembly and Assembly ..............3-2 Scale Calibration and Set Up Number Charts UM410 & UM520 ..........3-4 Scale Calibration and Set Up UM410 .................... 3-9 Scale Calibration and Set Up UM520 .................... 3-12 Downloader Module (Optional) ......................

  • Page 48: Wheel, Hub And Spindle Disassembly And Assembly

    1035, 1135 14,000 Lbs. 1596, 2096, V1000, V1100, 24,000 Lbs. 1950 16,000 Lbs. V1300 1113, 1313 24,000 Lbs. Unverferth Models: Parker Models: 760, 860, 1060 16,000 742, 842 12,000 Lbs. 1110, 1160, 5225, 6225, 524, 624, 739, 839, 1039 20,000 Lbs.
  • Page 49 — Operation & Maintenance Scales - Models 410 and 520 Wheel, Hub and Spindle Disassembly and Assembly 2. With the cart empty, use safe lifting device with a minimum weight rating per chart to sup- port the weight of your grain cart. Place the safe lifting device under the axle, near the tire. 3.
  • Page 50 — Operation & Maintenance Scales - Models 410 and 520 Scale Calibration & Set Up Number Charts UM410 & UM520 Brent Models - 472, 572, 576 Brent Model - 1080 Factory Set Up # 137060 Rigid Axle Single Wheels Single & Dual Wheels,...
  • Page 51 — Operation & Maintenance Scales - Models 410 and 520 Scale Calibration & Set Up Number Charts UM410 & UM520 Brent Model - 1282 (Serial Number B31270100-Up) Brent Models - V700, V800, V1000 Factory Set Up # 128160 Single Wheels & Tracks Single &...
  • Page 52 — Operation & Maintenance Scales - Models 410 and 520 Scale Calibration & Set Up Number Charts UM410 & UM520 Unverferth Models - 760, 860 Unverferth Model - 1110 Single & Dual Wheels Single Wheels & Tracks Factory Set Up #...
  • Page 53 — Operation & Maintenance Scales - Models 410 and 520 Scale Calibration & Set Up Number Charts UM410 & UM520 Unverferth Model - 1310 Unverferth Models - 7250, 8250 Single Wheels Factory Set Up # 127070 Single Wheels Factory Set Up #...
  • Page 54 — Operation & Maintenance Scales - Models 410 and 520 Scale Calibration & Set Up Number Charts UM410 & UM520 Killbros Models - 735 Parker Models - 842 Single & Dual Wheels Single & Dual Wheels Factory Set Up #...
  • Page 55 — Operation & Maintenance Scales - Models 410 and 520 Scale Calibration & Set Up UM410 For scale operation procedures, please refer to the UM410 Scale manual. Below are Calibration and Setup procedures: Scale Calibration 1. Press [ON] to turn on the scale.

  • Page 56: Scale Calibration And Set Up Um410

    The CAL message is displayed and then the CAL number. CAL Number Example: NOTE: Refer to “UM410 & UM520 Scale Calibra- tion & Set Up Number Charts” in this section for Set-Up or CAL numbers. 4. Press the [FIELD] key to increment the “flash- ing”...

  • Page 57: Scale Calibration And Set Up Um410

    — Operation & Maintenance Scales - Models 410 and 520 Scale Calibration & Set Up UM410 To Change Scale Upper Range 1. Press [ON] to turn on the scale. 2. To enter Setup press and hold the [ZERO] key, then press the [ON] key and hold them both together until the message displayed is “SETUP”, then let up on...

  • Page 58: Scale Calibration And Set Up Um520

    Enter D.A.N. code 871, press SELECT, current SETUP number will display. Enter the new SETUP number and press ENTER. 128120 “SETUP” number: Example: NOTE: Refer to “UM410 & UM520 Scale Calibra- tion & Set Up Number Charts” in this section for Set-Up or CAL numbers. To change CAL number: Enter D.A.N.

  • Page 59: Scale Kit Operation

    — Operation & Maintenance Scales - Models 410 and 520 Scale Kit Operation Position the empty grain cart on a firm, level surface next to the truck or wagon. Fold the auger into the unload position. 410 indicator: Press the Start/Stop button to show a temporary 0 on the screen. Engage augers, open the flow doors and unload the grain from cart while driving straight ahead.

  • Page 60: Scale "Short Form" Set Up & Calibration

    Self Test while numbers are displayed. Press [ON/OFF] key again to allow Self Test to complete normally. Verify the SETUP & CAL numbers with the Example table below and record the numbers on your UNVERFERTH indicator. SETUP#______________ CAL#___________ Keep this information for future reference.
  • Page 61 This indicator has the ability to match any other scale, even if that scale is uncalibrated. To match your UNVERFERTH Scale (Scale A) to another scale (Scale B) you must determine the Calibration Multiplier. To do this, place a load on Scale A (feed wagon, etc...) and write down the weight displayed.

  • Page 62: Unverferth 520 Indicator

    To change CAL number: Enter D.A.N. code 872, press SELECT, current CAL number will display. Enter the new CAL num- ber and press ENTER. NOTE: Refer to UM410 or UM520 Operator’s manual for any indicator set up or troubleshooting information. 3-16...

  • Page 63: Scale Troubleshooting

    — Operation & Maintenance Scales - Models 410 and 520 Scale Troubleshooting Does the indicator come on? BAD INDICATOR: If you suspect a bad indicator, the easiest way to check is to try another indicator. Even Is the reading on the indicator stable? if the indicator is a different model or is set-up for a different scale, it at least should come on.
  • Page 64 — Operation & Maintenance Scales - Models 410 and 520 Scale Troubleshooting (continued) Locating a suspected defective scale component When scale readings are unstable, flashing a message, non-responsive, etc., it is likely one com- ponent in the scale system is at fault and requiring replacement. Use the following procedure to identify which component needs to be replaced: 1.
  • Page 65 — Operation & Maintenance Scales - Models 410 and 520 Scale Troubleshooting (continued) Ensuring maximum accuracy Carts with compression load cells: 1. Canister load cells must be standing straight up and down. If leaning side to side or FIG. 3-1 forward/backward, spacer washers will need to be added to shift the axle side to side, or restrict excess axle movement.
  • Page 66 — Operation & Maintenance Scales - Models 410 and 520 Scale Troubleshooting (continued) Ensuring maximum accuracy (continued) 2. As the cart is lowered down onto the load cells, both should make contact at nearly the same time. If one load cell contacts significantly before the other, a 1/16” shim (280396) will need to be placed under one load cell.
  • Page 67 — Operation & Maintenance Scales - Models 410 and 520 Scale Troubleshooting (continued) Ensuring maximum accuracy (continued) 4. Grab each turnbuckle that retains the cart on top of the axle. Both should be loose when the cart is empty or loaded. 5.
  • Page 68 3 3/4” diameter front hitch bar (Unverferth #9004913 / Digi-Star #404760). Sev- eral other grain carts use a 3 3/4” diameter front hitch bar (Unverferth #9004910 / Digi-Star #404756). Consult your operators manual to verify that the correct hitch bar is installed for your application or contact Unverferth Product Support if necessary.
  • Page 69 — Operation & Maintenance Scales - Models 410 and 520 Scale Troubleshooting (continued) Ensuring maximum accuracy (continued) 15. Grain carts with walking tandem undercarriages or carts with single rear tires/wheels both use the same 3 3/4” diameter rear spindle with 2 drilled holes for mounting to the grain cart. The walking tandem cart utilizes the spindle hole located closest to the hub (3 1/2”...
  • Page 70 — Operation & Maintenance Scales - Models 410 and 520 Notes 3-24...
  • Page 71 Section IV Parts Please visit www.unverferth.com/parts/ for the most current parts listing. Please visit www.unverferth.com/parts/ for the most current parts listing. For your convenience the following chart has been supplied to assist you in selecting the correct scale parts for your unit.
  • Page 72 Section IV Parts Please visit www.unverferth.com/parts/ for the most current parts listing. Please visit www.unverferth.com/parts/ for the most current parts listing. For your convenience the following chart has been supplied to assist you in selecting the correct scale parts for your unit.
  • Page 73 Section IV Parts Please visit www.unverferth.com/parts/ for the most current parts listing. Please visit www.unverferth.com/parts/ for the most current parts listing. For your convenience the following chart has been supplied to assist you in selecting the correct scale parts for your unit.
  • Page 74 Section IV Parts Please visit www.unverferth.com/parts/ for the most current parts listing. Please visit www.unverferth.com/parts/ for the most current parts listing. For your convenience the following chart has been supplied to assist you in selecting the correct scale parts for your unit.
  • Page 75 — Parts Scales - Models 410 and 520 Section IV Parts Please visit www.unverferth.com/parts/ for the most current parts listing. Please visit www.unverferth.com/parts/ for the most current parts listing. SCALE PACKAGE PARTS Single Tires with 3-Point Scales Spindles ................4-6 Single Tires with 3-Point Scales Compression Cells ..............
  • Page 76 — Parts Scales - Models 410 and 520 Single Tires with 3-Point Scales Spindles - Components Please visit www.unverferth.com/parts/ for the most current parts listing. Please visit www.unverferth.com/parts/ for the most current parts listing. Model UM410 Model UM520...
  • Page 77 — Parts Scales - Models 410 and 520 Single Tires with 3-Point Scales Spindles - Components (continued) Please visit www.unverferth.com/parts/ for the most current parts listing. Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES...
  • Page 78 — Parts Scales - Models 410 and 520 Single Tires with 3-Point Scales Spindles - Components (continued) Please visit www.unverferth.com/parts/ for the most current parts listing. Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES...
  • Page 79 — Parts Scales - Models 410 and 520 Single Tires with 3-Point Scales Spindles - Components (continued) Please visit www.unverferth.com/parts/ for the most current parts listing. Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES...
  • Page 80 — Parts Scales - Models 410 and 520 Single Tires with 3-Point Scales Spindles - Components (continued) Please visit www.unverferth.com/parts/ for the most current parts listing. Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES...
  • Page 81 — Parts Scales - Models 410 and 520 Single Tires with 3-Point Scales Spindles - Components (continued) Please visit www.unverferth.com/parts/ for the most current parts listing. KIT NO. DESCRIPTION NOTES Unverferth Model: 5225 25144 UM410 Scale Package, Single Wheels Killbros Model: 1150...
  • Page 82 — Parts Scales - Models 410 and 520 Single Tires with 3-Point Scales Spindles - Components (continued) Please visit www.unverferth.com/parts/ for the most current parts listing. KIT NO. DESCRIPTION NOTES 265337 UM410 Scale Package, Single Wheels Brent Models: 472, 572, 576...
  • Page 83 — Parts Scales - Models 410 and 520 Notes Please visit www.unverferth.com/parts/ for the most current parts listing. 4-13...
  • Page 84 — Parts Scales - Models 410 and 520 Single Tires with 3-Point Scales Compression Cells - Components Please visit www.unverferth.com/parts/ for the most current parts listing. Please visit www.unverferth.com/parts/ for the most current parts listing. Model UM410 Model UM520 4-14...
  • Page 85 — Parts Scales - Models 410 and 520 Single Tires with 3-Point Scales Compression Cells - Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES UM520 Scale Package, Single & Dual Wheels Brent Models: 782, 882, 1082...
  • Page 86 — Parts Scales - Models 410 and 520 Single Tires with 3-Point Scales Compression Cells - Components (continued) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 9003630 Downloader Kit Option 9004149 Cable 5’ Long...
  • Page 87 — Parts Scales - Models 410 and 520 Notes Please visit www.unverferth.com/parts/ for the most current parts listing. 4-17...
  • Page 88 — Parts Scales - Models 410 and 520 Walking Tandems / Steerable Tandems / In-Line Tandems with 5-Point Scales - Components Please visit www.unverferth.com/parts/ for the most current parts listing. Model UM410 Model UM520 4-18...
  • Page 89 — Parts Scales - Models 410 and 520 Walking Tandems / Steerable Tandems / In-Line Tandems with 5-Point Scales - Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 284020 UM410 Scale Package, Steering Tandem...
  • Page 90 — Parts Scales - Models 410 and 520 Walking Tandems / Steerable Tandems / In-Line Tandems with 5-Point Scales - Components (continued) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES Models 1110, 1310, 1113, 1313,...
  • Page 91 — Parts Scales - Models 410 and 520 Walking Tandems / Steerable Tandems / In-Line Tandems with 5-Point Scales - Components (continued) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES Models 1110, 1310, 1113, 1313,...
  • Page 92 — Parts Scales - Models 410 and 520 Tracks with 5-Point Scales with Hydraulic Tensioning - Components Please visit www.unverferth.com/parts/ for the most current parts listing. Model UM410 Model UM520 4-22...
  • Page 93 — Parts Scales - Models 410 and 520 Tracks with 5-Point Scales with Hydraulic Tensioning - Components Please visit www.unverferth.com/parts/ for the most current parts listing. Model 1082 Only (Continued on next page) 4-23...
  • Page 94 — Parts Scales - Models 410 and 520 Tracks with 5-Point Scales with Hydraulic Tensioning - Components (continued) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES Models 1519, 1610, 1611, 1613, 1620, 251781 UM410 Scale Package, Tracks...
  • Page 95 — Parts Scales - Models 410 and 520 Tracks with 5-Point Scales with Hydraulic Tensioning - Components (continued) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES Models 1110, 1310, 1113, 1313, 1015, 1115, 1315, 1017, 1117, 1317, 1120,...
  • Page 96 — Parts Scales - Models 410 and 520 Tracks with 5-Point Scales with Hydraulic Tensioning - Components (continued) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES Models 1110, 1310, 1610, 1015, 1115, 1315, 1017, 1117, 1317, 1050, 1082, 9002130 Split Tension Bushing, 2”...
  • Page 97 — Parts Scales - Models 410 and 520 Tracks with 5-Point Scales with Hydraulic Tensioning - Components (continued) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES Models 1110, 1310, 1610, 1015, 1115, 1315, 1017, 1117, 1317, 1050, 1082,...
  • Page 98 — Parts Scales - Models 410 and 520 Single Tires with 5-Point Scales - Components Please visit www.unverferth.com/parts/ for the most current parts listing. Model UM410 Model UM520 4-28...
  • Page 99 — Parts Scales - Models 410 and 520 Single Tires with 5-Point Scales - Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES Models UM1160, KB1135, P1142, 1113, 1313, 1117, 1317, 1120, 1320, 1050, 1154, 1354,...
  • Page 100 — Parts Scales - Models 410 and 520 Single Tires with 5-Point Scales - Components (continued) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES Models UM1160, KB1135, P1142, 1113, 1313, 1115, 1315, 1017, 1117, 1317, 1120, 1320,...
  • Page 101 — Parts Scales - Models 410 and 520 Single Tires with 5-Point Scales - Components (continued) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES Models 1110, 1310, 1015, 1115, 1315, 1017, 9002130 Split Tension Bushing, 2” Dia.
  • Page 102 — Parts Scales - Models 410 and 520 Rotational Sensor Mounting Kit for UM520 Scale Please visit www.unverferth.com/parts/ for the most current parts listing. 15/16 6 7/8 REF 1 5/32 FINISH: THIS DRAWING IS PROPERTY OF WEIGHT 0.2 lbmass PAINT SQ 15.5...
  • Page 103 — Parts Scales - Models 410 and 520 Rotational Sensor Mounting Kit for UM520 Scale Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 251880 RPM Sensor Hardware Kit 9388-104 Carriage Bolt, 1/2-13UNC x 1 1/2 Gr.5 9390-056 Capscrew, 3/8-16UNC x 1 1/4 Gr.5...
  • Page 104 MANUALS\\266900///September 2015-2//March 2016-3//July 2016-4//September 2016-5//November 2016-6//May 2017-7//May 2018-8//October 2018-9//March 2019-10//May 2019-11//September 2019-12//November 2019-13...

This manual is also suitable for:

Um520

Table of Contents

Save PDF