Page 1
EverPlex 4CQ USER'S MANUAL Freeze EverPlex 4CQ NEXT P. DEFAULT Real Time Color Quad Processor High Resolution, Broadcast Quality Playback Zoom Function RS232 Remote Control Connect Up To 4 Cameras Ver. 1.0...
Notice...1 Important Messages ...2 Introduction...3 Specification ...4 Chapter I Functional Description...5 1. Front Panel Keypads...5 1.1 Full Screen ...5 1.2 Quad Display ...5 1.3 Freeze ...5 1.4 Sequential Switching...5 1.5 VCR Play Back ...5 1.6 Set ...6 1.6.1 Date, Time Setting, and OSD display on/off setting...7 1.6.2 Alarm Records ...7 1.6.3 Set the Brightness, Contrast, Color, Tint for each channel ...8 1.6.4 Set the camera titles ...8...
Notice This manual is presented to the users of EverPlex 4CQ by EverFocus Electronics Corp. With years of engineering researches, EverFocus has spared no effort to provide the high quality products to the worldwide users. For the policy of continual product improvement, EverFocus reserves the right to make changes to the product specifications and documentation without notice.
Important Messages: To prevent fire or shock hazard, do not expose this equipment to the environment of high humidity and dust. So, do not use it in an unprotected outdoor installation or any area classified as a wet area. Installation environment: The temperature should be kept between C ~ +50 disseminate the unit or put it on an unstable base.
EverPlex 4CQ, a real time color Quad and 4 channel auto switcher, is the best choice for multiple monitoring and recording. The superior video quality is achieved by adopting the advance multi-media technology. The picture of Quad display is sharp and clear because Everplex 4CQ is featured with CCIR601 full resolution and 16 million colors.
Video input: Video output: Title: Timer: Alarm input: Alarm output: Dimension: Power source: Power consumption: Specification 4 cameras + 1 VCR inputs Video output x 2, 1V p-p/75 ohm Up to 6 characters Built-in real time clock 4 alarm inputs and 1 alarm reset input 2 Alarm Out (1 Normally Open, 1 Normally Closed) 239 x 166 x 55 mm AC 24V or DC 12V...
Chapter I Functional Description EverPlex 4CQ 1. Front Panel Keypads 1.1 Full Screen Press any key of FULL SCREEN, the picture of the corresponding quadrant will fill the whole screen of the monitor display. Press the same key again, the quad display will come out.
Press the SET key to set time/date, title on/off, picture, camera titles, switching sequence, switching time period, alarm sensor type, alarm hold time, and the alarm/video loss records displaying. There are 6 pages in the setting mode : Page 1 : Set Time and Date.
1.6.1 Date, Time setting, and OSD display on/off setting DATE: 2000-01-01 TIME: 01:01:01 QUAD SCREEN DATE: QUAD SCREEN TIME: QUAD SCREEN TITLE: FULL SCREEN DATE: FULL SCREEN TIME: FULL SCREEN TITLE: VERSION N.NN DATE data format is CCYY-MM-DD, where CC : Century code from 19 to 20 YY : Year data from 00 to 99...
1.6.3 Set the Brightness, Contrast, Color, Tint for each channel BRIGHT: CONTRAST:27 COLOR: TINT: BRIGHT: CONTRAST:27 COLOR: TINT: 1.6.4 Set the camera titles Camera Title Setup CH1: CH2: CH3: CH4: 1.6.5 Set sequential switching parameters CH1 - CH4 to turn each channel ON or OFF in the sequential switching QUAD to turn QUAD display ON or OFF in the sequential switching SWITCH TIME : The time period to switch for each switching item REFRESH MODE : To set the screen refresh by 'FRAME' or by 'FIELD'.
1.6.6 Set alarm parameters Alarm Setting Menu CH SENSOR 1 N.O. 2 N.O. 3 N.O. 4 N.O. ALARM RESET IN : N.O. BUZZER KEY LOCK ALARM HOLD TIME: 05 SEC CH1 - CH4 to set the sensor input type as 'N.O.' : normally open, closed will invoke alarm 'N.C.' : normally closed, open will invoke alarm 'closed' means to short the alarm signal line to the ground...
Chapter II Back Panel Connection VIDEO INPUT 1. BNC Connectors MONITOR Connect this output port to the main monitor VCR OUT Connect this output port to the VIDEO IN of VCR. The quad video output of live video is obtained from this connector. VCR IN Connect this input port to the VIDEO OUT of VCR.
2.1 Alarm out There are two ways to do the alarm out connection: 2.1.1 Normally Open Connection (use pin # 1 and # 9) RELAY Alarm out EverPlex 4CQ 2.1.2 Normally Closed Connection (use pin # 1 and # 2) RELAY Alarm out EverPlex 4CQ...
2.2 Alarm in and Alarm reset There are 4 alarm sensors in for 4 channels and 1 alarm reset in, all these 5 alarm inputs can be set to Normally Open or Normally Closed by user and the setting menu. SENSOR 1 SENSOR 2 SENSOR 3...
The ALARM IN can be selected as normally open input or normally closed input: Normally Open If the alarm input is selected as Normally Open input, then the (N.O.) input is opened normally and shorted to the ground means an alarm happens.
3.1. The pin assignment of the 9 pin D-SUB connector EverPlex 4CQ PIN # NAME NOT CONNECTED NOT CONNECTED GROUND NOT CONNECTED NOT CONNECTED NOT CONNECTED NOT CONNECTED 3.2. Transmission Setting The transmission setting in the EverPlex 4CQ is 9600 baud rate, 1 start bit, 1 stop bit and no parity.
3.4. Alarm message sent via RS232 The EverPlex 4CQ will send out alarm message thru RS232 when any alarm occurs, the alarm message format are three ASCII characters followed carriage return and line feed, they are The first character is the leading code , '!' The second character is the alarm type, 'S' indicates a sensor alarm, 'V' indicates a video loss The third character is the channel number having the alarm, '1' ~ ’4' The fourth byte is the carriage return code, 0DH...
Page 18
EverFocus Electronics Corp. Head Office: 10F-6, No.79 Sec. 1 Shin-Tai Wu Road, Hsi-Chi, Taipei, Taiwan TEL: 886-2-26982334 FAX: 886-2-26982380 USA Office: 2445 Huntington Drive, San Marino, CA 91108, U.S.A. TEL: 1-626-844-8888 FAX: 1-626-844-8838 Toll free: 1-888-383-6287 or 1-888-EV-FOCUS Hong Kong Office: Room 0, 10/F., Block 3, Camelpaint Building, 60,...