Subscribe to Our Youtube Channel
Summary of Contents for Xtreme Polishing Systems Genie Magic 2
- Page 1 X T R E ME P OL I S H I N G S Y S T E MS 2 2 0 0 N W 3 2 n d S t r e e t , # 7 0 0 P o mp a n o B e a c h , F L 3 3 0 6 9 www.
-
Page 2: Table Of Contents
Walk-behind floor scrubber -www.xtremepolishingsystems.com 1.Index ................................4 2. GENERAL INFORMATION ........................4 2.1.Scope of the manual ........................4 2.2.Identifying the machine ........................5 2.3.Documentation provided with the machine .................. 5 3.TECHNICAL INFORMATION ........................5 3.1.General description .......................... 5 3.2. Legend ..........................6 3.3. -
Page 3: Index
Walk-behind floor scrubber -www.xtremepolishingsystems.com 1.Index GENERAL INFORMATION Read this manual carefully before carrying out any work on the machine 2.1. Scope of the manual This manual has been written by the Manufacturer and is an integral part of the machine. It defines the purpose for which the machine has been designed and constructed and contains all the information required by operators. -
Page 4: Identifying The Machine
Walk-behind floor scrubber -www.xtremepolishingsystems.com 2.2. Identifying the machine The rating plate located at the rear of the machine provides the following information: model code; • model; • power supply; • total nominal power; • serial number; • year of fabrication; •... -
Page 5: Legend
The machine is moved forward by: Genie Magic 2 mechanical drive the scrubber drier is provided with a special mechanical drive device which exploits the friction between the brush and the floor to generate a forward movement (for further details, see paragraph 6.7). -
Page 6: Safety Information
Walk-behind floor scrubber -www.xtremepolishingsystems.com A -Tank assembly: when using certain detergents, danger of irritation for eyes, skin, mucous, membranes and respiratory tract and of asphyxia Danger represented by the dirt collected from the environment (germs and chemical substances). Danger of crushing between the two tanks when the dirty water drum is replaced on the detergent tank. - Page 7 Walk-behind floor scrubber -www.xtremepolishingsystems.com do not use the machine transversally, always manoeuvre with care and do not reverse. When transporting the machine on steeper ramps or slopes, take the utmost care to avoid tipping up and/or uncontrolled acceleration. Move the machine on ramps and/or steps only with the brush head and squeegee raised.
- Page 8 Walk-behind floor scrubber -www.xtremepolishingsystems.com Never wash the machine with water jets. The fluids collected contain detergent, disinfectant, water and organic and inorganic material. They must be disposed off in accordance with current legislation. In the case of malfunction and/or faulty operation, turn the machine off immediately (Disconnecting it from the mains power supply or batteries) and do not tamper.
-
Page 9: Handling And Installation
Walk-behind floor scrubber -www.xtremepolishingsystems.com HANDLING AND INSTALLATION 5.1. Lifting and transporting the packaged machine IMPORTANT During all lifting operations, make sure the packaged machine is firmly anchored to avoid it tipping up or being accidentally dropped.Always load/unload lorries in adequately lit areas. The machine, packaged on a wooden pallet by the Manufacturer, must be loaded using suitable equipment onto the transporting vehicle. -
Page 10: Power Supply Batteries (Battery Models)
Walk-behind floor scrubber -www.xtremepolishingsystems.com The packaging may be kept as it can be reused to protect the machine if it is moved to another site or to a repair workshop. Otherwise it must be disposed off in compliance with current legislation. 5.4 Power supply batteries (battery models) Two different types of battery may be installed on these machines: tubular leak-proof batteries: the electrolyte level must be checked regularly. - Page 11 Walk-behind floor scrubber -www.xtremepolishingsystems.com ! DANGER push ensure stopping machine Make sure you connect the terminals marked with a "+" to the positive poles of the battery. Do not check the battery charge by sparking. Follow the instructions given below meticulously as short circuiting the batteries could cause them to explode。...
-
Page 12: Battery Charger (Battery Models)
Walk-behind floor scrubber -www.xtremepolishingsystems.com 5)Lower the dirty water drum into its work position and fasten it to the detergent tank 。 6)When using the machine, follow the instructions below 5.5 Battery charger (battery models) IMPORTANT Never allow the batteries to become excessively flat as this could damage them irreparably. 5.5.1. -
Page 13: Practical Guide For The Operator
Walk-behind floor scrubber -www.xtremepolishingsystems.com lift the pallet (with the machine) using a fork lift truck and load it onto the means • of transport; • anchor the machine to the means of transport with cables connected to the pallet and machine itself PRACTICAL GUIDE FOR THE OPERATOR 6.1. -
Page 14: Mounting And Adjusting The Squeegee
Walk-behind floor scrubber -www.xtremepolishingsystems.com Picture (14) Step to the end, shift left ; brush plate will down. Step to the end, shift downward ; brush plate upgrade. Detergent tank level indicator: • the LED comes on to indicate insufficient water in the detergent tank. Dirty water drum level indicator: •... -
Page 15: Moving The Machine When Not In Operation
Walk-behind floor scrubber -www.xtremepolishingsystems.com for perfect drying. With time, the constant rubbing makes the edge of the blade in contact with the floor rounded and cracked, reducing the drying efficiency and requiring it to be replaced. The state of wear should be checked frequently. For perfect drying, the squeegee must be adjusted in such a way that the edge of the rear blade bends during operation by about 45°... -
Page 16: Detergents - Instructions
Walk-behind floor scrubber -www.xtremepolishingsystems.com symmetrically. Rotate clockwise to Make 3 columns fast on the brush motor buckle, rotate stable is ok.(if the machine shakes when running, it means installation not good,please redo),As the picture (19) shown. Picture (19) Use Cleaning pad:stick cleaning pad onto pad driver first,then install pad driver to scrubber as the way install brush. -
Page 17: Start Working
Walk-behind floor scrubber -www.xtremepolishingsystems.com Check batter power(please charge first if the power is not enough) Step brush plate footboard to release the font brush plate. Fill with water to the water tank (make sure the recovery tank is empty) before fill water,please must pay attention to make the solution tank net. - Page 18 Walk-behind floor scrubber -www.xtremepolishingsystems.com Picture (20) *touch water sucntion button and brush motor button successively, start working right now. *control operation handle to go forward to clean ground. *After bush motor button pressed,the motor start drive brush plate, machine go forward. Machine go forward with the force that generated between brush plate and ground.
-
Page 19: Some Useful Tips To Get The Most From Your Scrubber Drier
Walk-behind floor scrubber -www.xtremepolishingsystems.com AC machines: Please unplug the AC power plug. Battery machines: Please remove the battery connector plug from the body socket. Empty and clean the recovery tank. 6.8. Some useful tips to get the most from your scrubber drier In the event of particularly stubborn dirt on the floor, washing and drying can be performed in two separate operations. -
Page 20: Empty Water Tank
Walk-behind floor scrubber -www.xtremepolishingsystems.com For a quick release of sewage, pull sewage pipes completely straight, as picture (25) shown. Picture (22) Picture (23) Picture (24) Picture (25) Check the amount of water inside the water tank, clean water tank if necessary. To make cleaning easier, and completely empty the water inside, we recommend that you loose and lift the sewage tank. -
Page 21: Battery Maintenance And Charging
Walk-behind floor scrubber -www.xtremepolishingsystems.com BATTERY MAINTENANCE AND CHARGING Danger Do not check the battery by sparking. The batteries give off flammable fumes. Put out all fires and hot embers before checking or topping up the batteries. Perform the operations described above in a ventilated room. To avoid permanent damage to the batteries, do not run them down completely. -
Page 22: Routine Maintenance
Walk-behind floor scrubber -www.xtremepolishingsystems.com Performing regular maintenance according to the Manufacturer's instructions improves performance and extends the working life of the machine. When cleaning the machine, respect the following: · avoid the use of high pressure washers. Water could penetrate the electrical compartment or motors leading to damage or the risk of short circuit;... - Page 23 Walk-behind floor scrubber -www.xtremepolishingsystems.com · lower the squeegee by means of the corresponding lever; picture 31 · remove the squeegee from its mount by completely unscrewing the two knobs · remove the suction hose sleeve from the squeegee; · release the catch; ·...
-
Page 24: Fuses: Replacement
Walk-behind floor scrubber -www.xtremepolishingsystems.com Fuses: replacement The fuses protecting the brush and suction motors are located in the fuse holder attached to the dirty water drum above the machine battery compartment. To replace the fuses: make sure the dirty water drum is empty and empty if necessary; raise the dirty water drum;... -
Page 25: Six Monthly Operations
Walk-behind floor scrubber -www.xtremepolishingsystems.com · Clean the dirty water drum float switch and make sure it is working correctly; · clean the suction air filter and make sure it is undamaged. If necessary, replace. · clean the detergent filter at the front opening of the detergent tank and check that it is not damaged (replace if necessary);... - Page 26 Walk-behind floor scrubber -www.xtremepolishingsystems.com The tap lever is in the Mover the lever to Open closed position position there is no water Fill in it the hose delivering the No detergent is Cleaning the hose. detergent delivered brush is blocked Strainer is plugged Cleaning the stainer Unscrew , cleaning it or...
- Page 27 Walk-behind floor scrubber -www.xtremepolishingsystems.com the second case, checkthe brush/drive motor is correctly connected to the main wiring; in the third case replace the motor the reduction unit is broken (therefore the brush does Replace it not move) the brush motor thermal Top the machine,turn it off cutout and leave it to cool at least...
Need help?
Do you have a question about the Genie Magic 2 and is the answer not in the manual?
Questions and answers