- Parts and Buttons ............12 - Connecting the Stand ..........13 - Connecting the IR Sensor .........14 - Portrait Layout ..............17 - Attaching and removing the LG Logo Bracket ..- Assembling the Memory Cover......20 - Installing on a Wall ............21 REMOTE CONTROL ....23 MAKING CONNECTIONS ...
WARNING - This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may cause radio interference. SAFETY PRECAUTION Please read these safety precautions carefully before using the product. WARNING If you ignore the warning message, you may be seriously injured or there is a possibility of accident or death. CAUTION If you ignore the caution message, you may be slightly injured or the product may be damaged.
Page 4
If you install the product in a place that does not meet the recommended conditions, this may cause serious damage to the product’s picture quality, life cycle, and appearance. Please check with LG or a qualified installer before installing. This caution applies to a place where there is an abundance of fine dust or oil mist, chemical substances are used, the temperature is very high or low, the humidity is very high, or the product is likely to remain turned on for a long period of time (airport and train station).
- If loosely connected, the poor connection may cause a fire or electric shock. • Be sure to use power cords and AC adapters provided or approved by LG Electronics, Inc. - The use of non-approved products may cause a fire or electric shock.
Page 6
• Do not touch the power plug with wet hands. Additionally, if the cord pin is wet or covered with dust, dry the power plug completely or wipe dust off. - You may be electrocuted due to excess moisture. • If you don’t intend to use the product for a long time, unplug the power cable from the product.
Precautions In Moving the Product WARNING • Make sure to turn off the product. - You may be electrocuted or the product can be damaged. • Make sure to remove all cables before moving the product. - You may be electrocuted or the product can be damaged. •...
CAUTION • Do not put or store inflammable substances near the product. - There is a danger of explosion or fire due to careless handling of the inflammable substances. • When cleaning the product, unplug the power cord and scrub gently with a soft cloth to prevent scratching. Do not clean with a wet cloth or spray water or other liquids directly onto the product.
SuperSign Software & Manual - Downloading from the LG Electronics website. - Visit the LG Electronics website (http://partner.lge.com) and download the latest software for your model. • The warranty will not cover any damage caused by using the product in an excessively dusty environment.
Optional Accessories Without prior notice, optional accessories are subject to change to improve the performance of the product, and new accessories may be added. The illustrations in this manual may differ from the actual product and accessories. Stand kit Screws ST-653T Diameter 4.0 mm x Pitch 0.7 mm x Length 12.0 mm Media Player kit...
Page 11
OPS kit Screws Screws KT-OPSF Diameter 3.0 mm x Length 8.0 mm Diameter 3.0 mm x Length 8.0 mm Card (Easy Setup Guide) Power Cord Connecting Cable NOTE • Before you attach the OPS kit or Media Player, connect the cable to the port.
Parts and Buttons The image may be different according to the model. Power On (Press) Quick Menu (Press Volume Control Menu Control Menu Selection (Press Menu Control Power Off (Press and Hold) 1 When the monitor is turned on, press the button one time.
Connecting the IR Sensor When you connect the cable to the product, the feature for receiving remote control signals is activated. Rotate the IR sensor according to the screen orientation (Landscape/Portrait). - The image may be different according to the model. Basic installation [Front] [Rear]...
Portrait Layout When installing in a portrait layout, rotate the monitor counterclockwise 90 degrees (when facing the screen). Using Kensington Lock (This is not available for all models.) The Kensington security system connector is located at the back of the monitor. For more information on installation and use of this system, refer to the manual provided with the Kensington security system or visit http://www.
LG Logo Bracket to the bottom rear of the monitor. LG Logo Bracket After removing the screw, remove the LG Logo Bracket. When re-attaching the LG Logo Bracket, repeat the process in reverse order.
Page 19
LG Logo Bracket to the bottom rear of the monitor. LG Logo Bracket After removing the screw, remove the LG Logo Bracket. Attach the LG Logo Bracket with a screw, aligning it with the hole on the right side.
Screws which are longer than standard length may damage the inside of the monitor. A non-VESA standard screw may damage the product and cause the monitor to fall. LG Electronics is not liable for any accidents related to the use of non-standard screws.
Page 22
Disconnect the power cord before moving or installing the monitor to avoid risk of electric shock. • If you install the monitor on a ceiling or slanted wall, it may fall and result in injury. Use an authorized LG wall mount and contact your local dealer or qualified personnel to assist with the installation.
REMOTE CONTROL The descriptions in this manual are based on the buttons on the remote control. Please read this manual carefully to use the monitor correctly. To install batteries, open the battery cover, place batteries (1.5 V AAA) matching terminals to the labels inside the compartment, and close the battery cover. To remove the batteries, perform the installation actions in reverse.
Page 24
Selects the Picture Mode. (HOME) Activates the Launcher. Enters the White Balance menu. (SETTINGS) Accesses the main menus or saves your input and exit menus. This function is not supported. (Navigation Buttons) Scrolls through menus or options. Selects menus or options and confirms your input. (BACK) Allows you to move back one step in the user interaction function.
MAKING CONNECTIONS You can connect various external devices to your monitor. Change the input mode and select the external device you want to connect. For more information about external device connections, see the user manual provided with each device. Connecting to a PC Some of the cables are not provided.
NOTE • For the best image quality, using the monitor with HDMI connection is recommended. • To comply with the specifications of the product, use a shielded interface cable with ferrite core, such as a DVI-D/ HDMI cable. • If you turn the monitor on when the set is cold, the screen may flicker. This is normal. •...
Connecting Multiple Monitors To use multiple monitors connected to each other, connect the end of the signal input cable (DP cable) to the DP OUT connection in one monitor and connect the other end to the DP IN connection of the other monitor. * DP Cable: Use a DP cable that is certified to a DP 1.1a (SST) standard or higher.
TROUBLESHOOTING No image is displayed. Problem Action Is the product power cord connected? • Check if the power cord is correctly plugged into the power outlet. Does the “Invalid Format” message • The signal from the PC (Graphics card) is out of the vertical or appear? horizontal frequency range of the product.
Page 29
After-image appears on the product. Problem Action After-image appears when the product is • If you use a fixed image for a long time, the pixels may be damaged. turned off. Use the screen-saver function. • When a dark image is displayed on the screen after an image with high contrast (black and white or gray), this may cause image sticking.
Page 30
CAUTION • Image sticking does not occur when using constantly changing images but may occur when using a fixed image for an extended period of time. Therefore, it is recommended that you use the instructions below to decrease the likelihood of image sticking occurring when using a fixed image.
PRODUCT SPECIFICATIONS The product specifications below may be changed without prior notice due to upgrade of product functions. “ ” refers to alternating current (AC), and “ ” refers to direct current (DC). LCD screen Screen type Thin Film Transistor (TFT) Liquid Crystal Display (LCD) Screen Video signal Maximum resolution...
Page 32
43UH5F LCD screen 0.2451 mm (H) x 0.2451 mm (V) Pixel pitch Power AC 100-240 V ~ 50/60 Hz 1.2 A Rated power Power consumption On Mode: 75 W (Typ.) Sleep Mode : ≤ 0.5 W Off Mode : ≤ 0.5 W Dimensions (Width x 962.5 mm x 568.0 mm x 39.9 mm / 11.2 kg...
Page 33
49UH7F LCD screen 0.27963 mm (H) x 0.27963 mm (V) Pixel pitch Power AC 100-240 V ~ 50/60 Hz 1.6 A Rated power Power consumption On Mode: 100 W (Typ.) Sleep Mode : ≤ 0.5 W Off Mode : ≤ 0.5 W Dimensions (Width x 1098.6 mm x 644.5 mm x 39.9 mm / 15.4 kg Head...
Page 34
43UM3F / 43UM3DF LCD screen 0.2451 mm (H) x 0.2451 mm (V) Pixel pitch Power AC 100-240 V ~ 50/60 Hz 1.2 A Rated power Power consumption On Mode: 70 W (Typ.) Sleep Mode : ≤ 0.5 W Off Mode : ≤ 0.5 W Dimensions (Width x 962.5 mm x 568.0 mm x 39.9 mm / 11.2 kg Head...
Page 35
Wireless module(LGSBWAC72) Specifications Wireless LAN (IEEE 802.11a/b/g/n/ac) Frequency range (MHz) Output power (Max.) (dBm) 2400 to 2483.5 5150 to 5725 16.5 5725 to 5850 (Not for EU) 11.5 Bluetooth Frequency range (MHz) Output power (Max.) (dBm) 2400 to 2483.5 • As band channels can vary per country, the user cannot change or adjust the operating frequency.
Page 36
HDMI/ DVI-D/ DisplayPort/ OPS (PC) Support mode Resolution Horizontal frequency (kHz) Vertical frequency (Hz) Remark 800 x 600 37.879 60.317 1024 x 768 48.363 1280 x 720 44.772 59.855 1280 x 1024 63.981 60.02 1680 x 1050 65.29 59.954 1920 x 1080 67.5 3840 x 2160 67.5...
Page 37
NOTE • Horizontal frequency: The horizontal interval is the time taken to display one horizontal line. When 1 is divided by the horizontal interval, the number of horizontal lines displayed every second can be tabulated as the horizontal frequency. The unit is kHz. •...
LICENSES Supported licenses may differ by model. For more information of the licenses, visit www.lg.com. The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. Manufactured under license from Dolby Laboratories. Dolby, Dolby Vision, Dolby Audio, Dolby Atmos, and the double-D symbol are trademarks of Dolby Laboratories.
Page 39
This product qualifies for ENERGY STAR®. Changing the factory default configuration and settings or enabling certain optional features and functionalities may increase energy consumption beyond the limits required for ENERGY STAR® certification. Refer to ENERGYSTAR.gov for more information on the ENERGY STAR®...
Page 40
USER MANUAL LG Digital Signage (MONITOR SIGNAGE) Please read this manual carefully before operation and retain it for future reference. webOS 4.1 www.lg.com...
Page 42
- Command Reference List ..........58 terms, warranty disclaimers and copyright notices - Transmission/Reception Protocol ......63 are available for download. LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping, and handling) upon email request to opensource@lge.com.
NOTE • Software-related content may be changed without prior notice due to upgrades of the product functions. • Some features described in the User Manual may not be supported in certain models and countries. • SNMP 2.0 is supported. SETTINGS Home Global Buttons •...
Ez Setting [Video Wall] [Ez Setting] [Video Wall] Set Video Wall options to create a wide visual canvas. • [Tile Mode]: Turn [Tile Mode] on or off. • [Tile Mode Settings]: Display a single integrated screen on multiple Signage monitors. •...
[Server Setting] [Ez Setting] [Server Setting] Set up to connect your signage to a SuperSign server. • CMS Server • Control Server [Fail Over] [Ez Setting] [Fail Over] Set the priority of the input devices when a fault occurs. Automatically play the content stored in the device or run the set app.
Page 46
NOTE • If the status regarding any of the following items changes or becomes abnormal, a status message can be sent. - 1. Temp. Sensor: If the set reaches a dangerous temperature, its current temperature is recorded, and an email containing such information is sent.
[Play via URL] [Ez Setting] [Play via URL] Play content you want to play automatically through the built-in web browser. • [URL Loader]: Turns [Play via URL] on or off. • [Set URL]: Enter the URL address to display automatically. •...
[Signage 365 Care] [Ez Setting] [Signage 365 Care] You can install the Signage 365 Care (fault diagnosis) solution for fault diagnosis and prediction service. • [Install]: Installs the Signage 365 Care solution. 1) [ENTER ACCOUNT NUMBER]: Enters the 6-digit account number to install the Signage 365 Care solution. - Account Number: The number assigned when the Signage 365 Care solution is registered.
[Multi Screen] [Ez Setting] [Multi Screen] This feature allows you to view multiple external inputs and videos on a single screen. PIP Mode PBP Mode 3-Screen Split Mode 4-Screen Split Mode NOTE • In multi-screen mode, the DP daisy chain feature is not supported. •...
Page 50
Changing Screen Input Press the button on the top right of each split screen to select the desired input. NOTE • Inputs which have already been selected for other split screens cannot be selected again. To select them, press the RESET button to reset the inputs for all screens first.
[Leveler Tool] [Ez Setting] [Leveler Tool] You can check the horizontal and vertical level status when installing the product. Check the tilt of the product • The bubble and angle indicator in the leveler show the degree of tilt of the product. •...
General [Language] [General] [Language] You can select the menu language to be displayed on the screen. • [Menu Language]: Sets the language of your Signage monitor. • [Keyboard Language]: Sets the language of the keyboard displayed on the screen. [System Information] [General] [System Information] This feature displays information such as the device name, software version, and storage space.
Page 53
[Power] [General] [Power] Power-related feature settings [No Signal Power Off (15 Min)] Set whether to use the 15 Min Auto Off feature. • You can set this option to [On] or [Off]. • If you set this feature to [On], the product turns off after it’s remained in No Signal status for 15 minutes. •...
Page 54
[PM Mode] • [Power Off (Default)]: Set the normal DC off mode. • [Sustain Aspect Ratio]: Identical to normal DC off mode except that the Switching IC remains on. On certain models, this applies only to a specific input mode (DisplayPort) and has the same effect as [Screen Off Always] in other input modes.
Page 55
[Power Indicator] • This function enables you to change the [Power Indicator] settings. • Setting to [On] will turn on [Power Indicator]. • Setting to [Off] will turn off [Power Indicator]. • Regardless of [On] or [Off] settings in [Power Indicator], [Power Indicator] will be turned on for approximately 15 seconds.
Page 56
[LAN Daisy Chain] • LAN Daisy Chain forms a daisy chain of LAN ports so that even if you connect only one monitor set to a network, the other sets in the daisy chain are connected to the network. • However, the first monitor set in the daisy chain must be connected to the network through a port that is not used for the daisy chain connection.
Page 57
For details, contact your ISP. • LG is not responsible for any malfunction of the display or Internet connection failures due to communication errors/ malfunctions associated with your Internet connection or other connected equipment.
Page 58
Tips for When Configuring Wireless Network Settings • The wireless network may be affected by interference from a device that uses 2.4 GHz frequency, such as a wireless telephone, Bluetooth device or microwave. Interference may also be caused by a device that uses 5 GHz frequency such as Wi-Fi devices.
Page 59
[Safety Mode] [General] [Safety Mode] Set to this function for safe performance. [ISM Method] If a still image is displayed on the screen for an extended period of time, image sticking can occur. The ISM method is a feature that prevents image sticking. [Mode] •...
Page 60
[Start Time] • Set the Start time. • This option is available only when [Repeat] is set to [Schedule]. • You cannot set the same time for Start time and End time. [End Time] • Set the End time. • This option is available only when [Repeat] is set to [Schedule].
Page 61
2.4GHz. • When you set iBeacon, LG Beacon will be set to be the same as the value of iBeacon field. But the LG Beacon setting item won’t be provided separately.
Page 62
[Control Interface] Devices connected to the display can be controlled via the interface. • [PC/OPS Power Control]: Enable you to control the power of PC or OPS as you turn the display on and off. - [Disable]: Disable [PC/OPS Power Control]. - [Sync(On)]: Set the PC/OPS power to be turned on when the display is turned on.
Page 63
[SIMPLINK Setup] • When the [SIMPLINK Setup] is set to [On], you can use the SIMPLINK provided by LG Signage. • [Device ID]: Set the ID of the device connected via CEC wiring. You can choose a value between [All] and [E].
Display [Picture Mode] [Display] [Picture Mode] [Mode] This feature enables you to choose the optimal picture mode for your installation environment. • [Mall/QSR], [Transportation], [Education], [Gov./Corp.]: Display the picture optimally for your installation environment. • [Normal]: Display the picture at normal contrast, brightness, and sharpness. •...
Page 65
[Customize] • [Backlight]: Adjust the brightness of the screen by adjusting the brightness of the backlight. The closer the value is to 100, the brighter the screen is. • [OLED Light]: Adjusts the brightness of the LED panel to control the brightness of the screen. •...
Page 66
• [Picture Option]: Customize the picture options. - [Noise Reduction]: Remove randomly popping dots to make the picture look clearer. - [MPEG Noise Reduction]: Reduce the noise generated in the process of creating a digital video signal. - [Black Level]: Adjust the brightness and contrast of the screen by adjusting the black level of the screen. (Recommended settings based on input signals: Backlight 0 - 255 High, RGB 16 - 235: Low, YCbCr: Low) - [Real Cinema]: Optimize the video image for a cinematic look.
[Aspect Ratio] [Display] [Aspect Ratio] This feature enables you to change the picture size to view the picture at its optimal resolution. • [Full Wide]: Stretch the picture to fill the screen. • [Original]: Display the picture at its original resolution. [Rotation] [Display] [Rotation]...
[Expert Controls] [Display] [Expert Controls] [UHD Deep Color] If you connect an HDMI, DP, or OPS device to one of the Deep Color adjustable ports, you can select between UHD Deep Color On (6G) or Off (3G) in the UHD Deep Color settings menu. If a compatibility issue occurs with a graphics card when the Deep Color option is set to On at 3840 x 2160 @ 60 Hz, set the Deep Color option back to Off.
[HDMI IT Content] Set the HDMI IT Contents function. • [Off]: Disable the HDMI IT Contents function. • [On]: Enable the HDMI IT Contents function. This feature automatically changes the monitor's picture mode based on HDMI Contents information when an HDMI signal is entered.
Sound [Sound Mode] [Sound] [Sound Mode] [Sound Mode] The best sound quality will be selected automatically depending on the video type currently being watched. • [Standard]: This sound mode works well for content of all types. • [Cinema]: Optimize sound for watching movies. •...
Some recently connected devices may automatically attempt to reconnect to the Signage monitor when it is turned • It is recommended that you set LG audio devices that support LG Sound Sync to LG TV mode or LG Sound Sync mode before connecting.
[External Speaker] (0~15): Adjust the sync between video and audio coming from external speakers, such as those connected to the digital audio output port, LG audio equipment, or headphones. The larger the number is, the slower the voice output is than the default value.
Admin [Lock Mode] [Admin] [Lock Mode] [Home Dashboard Lock] When you set the Home Dashboard Lock, you can limit the change in the settings of the Home Dashboard. [USB Lock] This feature enables you to configure the USB lock feature so that settings or content cannot be changed. [OSD Lock] This feature enables you to configure the OSD lock feature so that settings or content cannot be changed.
[Change Password] This feature enables you to set the password you use to enter the Installation menu. (The default password: 000000) Enter your current password. Enter a new 6-digit password. Enter the same password again in the Confirm Password field for confirmation. [Enterprise Settings] •...
CONTENT MANAGER Web Login • Different features are supported depending on the product. This Signage product comes with a feature that enables you to access it on your PC or mobile device. - Content Manager, Group Manager 2.0, Control Manager, Log Out, Change Password menus are provided. •...
Page 76
[Delete] Select your desired type of content from the tab on the left and click [Delete] in the upper right-hand corner of the screen. Select the content you wish to delete. Click [Delete] in the upper right-hand corner of the screen. You can see that the content has been deleted.
Page 77
[Scheduler] (Scheduler) The Content Manager app's scheduler feature enables certain content to be played at a scheduled time through a playlist or external input. [Creating a Schedule] Click [New Schedule] in the upper right-hand corner of the screen. Choose between [Playlist] and [Input Source]. 1) If you have selected [Playlist], select the playlist you wish to schedule the playback of.
Page 78
[Delete Schedule] Click [DELETE] in the upper right-hand corner of the screen. Select the schedules you wish to delete. Click [DELETE]. Check that the schedules have been deleted. [Calendar View] When you have registered schedules, click [Calendar View]. You can see that the schedules registered are displayed in the form of a timetable. [Distribute] Click [Distribute] in the upper right-hand corner of the screen.
Page 79
Supported Photo & Video Files NOTE • Subtitles are not supported. • The photo feature is not supported in OLED model. Supported video codecs Extension Codec .asf, .wmv Video VC-1 Advanced Profile (except for WMVA), VC-1 Simple and Main Profiles Audio WMA Standard (excluding WMA v1/WMA Speech) .avi...
Page 80
Supported Photo File Formats File type Format Resolution .jpeg, .jpg, .jpe JPEG • Minimum: Min: 64 x 64 • Maximum: Normal Type: 15360 (W) x 8640 (H) Progressive Type: 1920 (W) x 1440 (H) .png • Minimum: Min: 64 x 64 •...
Page 81
• If your USB storage device has multiple partitions, or if you use a USB multi-card reader, you can use up to four partitions or USB memory devices. • If a USB storage device is connected to a USB multi-card reader, its volume data may not be detected. •...
Group Manager 2.0 This feature enables you to group together multiple monitor sets on a single network into the same group and to distribute content (schedules and playlists) or copy setting data on a group basis. This feature has two modes, Master and Slave, and it can access the browser on your PC or mobile device.
Page 83
[GROUP MANAGEMENT] • Creating a New Group 1. Click [Add New Group]. 2. Enter a group name. 3. Click [Add Device], select the devices you wish to add to the group, and add them. 4. Click [Done], and you will see that a new group has been created. •...
Page 84
[Setting Data Cloning] Select your desired group and click Clone. Check that the data have been copied on the slave sets. [Content Distribute] Select the type of content you wish to distribute (Schedules or Playlists). Select the content you wish to distribute. Select the group to which you wish to distribute the content and click [Distribute].
“Devices” on your laptop. Click “Add Device” in the top center of the screen, and then you will see a list of nearby WiDi-capable LG Signage monitors. From the list of detected Signage monitors, select one you wish to connect to and click Connect.
This feature is to display the PC (Windows or Mac OS) screen on the Signage monitor with wired/wireless connection to the PC. To use this feature, you need to install LG Presenter PC Client (“Client”) on the PC. You can use LG Presenter in the following ways.
To connect to the Signage device, enter the PIN code shown the Signage device. CAUTION • The Signage device and the PC must be on the same network. • If a specific port (UDP 1900) of your LG Signage is blocked, the LG Presenter feature will not be available.
Screen Share Select the screen you want to share and press the Share button. To leave Screen Share, press the Stop button. Item Description Connection status It shows the currently connected user's name and you can also disconnect here. Screen list It shows the list of PC screens available to share.
If you approve the request for hand over, the Signage device will be disconnected, and the Client on PC2 will be connected to the Signage device. If you deny the request for hand over, the Signage device will remain connected, so you can continue to use the features of LG Presenter. Item Description...
MANAGEMENT TOOLS Admin Control and check the status of the display through the Web browser. This function is available for PCs and mobile devices. Different features are supported depending on the product. Function • [Dashboard]: Display a summary of the product's status and provides links to each page. •...
Picture ID AUDIO (RGB/DVI) RS-232C OUT RS-232C OUT RS-232C OUT [Picture ID] is used to change the settings of a specific set (display) using a single IR receiver for multi-vision. Communication is possible between a monitor with an IR receiver and other monitors using RS-232C cables. Each RS-232C IN RS-232C IN RS-232C IN...
TO CONTROL AN EXTERNAL PC USING TOUCH SCREEN • This only applies to certain models. Connecting to a PC Connecting this product to a PC with a USB cable (Type A to Type B) allows you to control the connected PC by touching the screen of the product.
IR CODE • All models do not support the HDMI/USB function. • Some key codes may not be supported depending on the model. Code (Hex) Function Remarks Remote control button (Power) MONITOR ON Remote control button MONITOR OFF Remote control button (Energy Saving) Remote control button INPUT (Select input)
Page 94
Code (Hex) Function Remarks (Settings/Menu) Remote control button Auto Configuration Remote control button (Up) Remote control button (Down) Remote control button Remote control button (Right) (Left) Remote control button Remote control button (OK) (BACK) Remote control button Tile Remote control button Exit Remote control button Picture ID On (red)
CONTROLLING MULTIPLE PRODUCTS • This only applies to certain models. Use this method to connect several products to a single PC. You can control several products at a time by connecting them to a single PC. In the Option menu, the Set ID must be between 1 and 1000 without being duplicated. Connecting cables •...
Communication Parameter NOTE • When using 3-wire connections (non-standard), an IR Baud Rate: 9600 BPS daisy chain cannot be used. Data Length: 8 bits • Be sure to only use the provided gender to connect Parity Bit: None properly. Stop Bit: 1 bit •...
Command Reference List Command Data (Hexadecimal) [Power] 00 to 02 Select Input See Select Input [Aspect Ratio] See [Aspect Ratio] [Brightness Control] 00 to 04 [Picture Mode] See [Picture Mode] [Contrast] 00 to 64 [Brightness] 00 to 64 [Sharpness] 00 to 32 [Color] 00 to 64 [Tint]...
Command Data (Hexadecimal) [Software Version] [White Balance] Red Gain 00 to FE [White Balance] Green Gain 00 to FE [White Balance] Blue Gain 00 to FE [White Balance] Red Offset 00 to 7F [White Balance] Green Offset 00 to 7F [White Balance] Blue Offset 00 to 7F [Backlight]...
Page 99
Command Data (Hexadecimal) [Power On Status] 00 to 02 Wired [Wake On LAN] 00 to 01 [Screen Rotation] 00 to 03 [Time Sync] n, 16 00 to 01 [Contents Sync] 00 to 01 [LAN Daisy Chain] n, 84 00 to 01 [External Input Rotation] n, 85 00 to 03...
Page 100
Command Data (Hexadecimal) [Digital Audio Input] n, a2 00 to 01 [Booting Logo Image] n, a3 00 to 01 [SoftAP] n, a4 00 to 01 [Natural Size] n, a5 00 to 64 Play Saved Internal Media n, a8 See Playback of Saved Internal Media [No Signal Image] n, a9 00 to 01...
Page 101
Command Data (Hexadecimal) [Frame Control] n,b7 00 to 01 [Average Picture Level Auto n,be 00 to 01 Control] Read Brightness Value [Screen Fault Detection] 00 to 01 [Stereo Mode] n,c2 00 to 02 [HDR Picture Mode] n,c4 See [HDR Picture Mode] [Dynamic Tone Mapping] n,c5 00 to 01...
Transmission/Reception Protocol Transmission (Command1)(Command2)( )(Set ID)( )(Data)(Cr) * (Command1): This command is used to identify between the adjustment setting or the user adjustment modes. * (Command2): This command is used to control the monitor. * (Set ID): Used for selecting a set you want to control. A unique Set ID can be assigned to each set ranging from 1 to 1000 (01H to FFH) under Settings in the OSD menu.
01. [Power] (Command: k a) Acknowledgment (b)( )(Set ID)( )(OK/NG)(Data)(x) Controls the power on/off status of the monitor. * Some input signals may not be available for all models. Transmission * If it is not distributed from SuperSign W, WebOS Player (k)(a)( )(Set ID)( )(Data)(Cr) returns NG.
16. [Current Time] 1 (year/month/day) (Command: 18. [No Signal Power Off(15Min)] (Command: f g) f a) Sets the monitor to enter Automatic Standby mode if there is no signal for 15 minutes. Sets the Clock 1 (year/month/day) values and Auto Time. Transmission Transmission (f)(g)( )(Set ID)( )(Data)(Cr)
21. [Default] Settings (Command: f k) 24. Time Elapsed (Command: d l) Executes Reset. Displays the time that has elapsed after your monitor has turned on. (Initialize Screen can only be executed in RGB input mode.) Transmission Transmission (d)(l)( )(Set ID)( )(Data)(Cr) (f)(k)( )(Set ID)( )(Data)(Cr) Data FF: Read status...
Page 108
27. [White Balance] Red Gain (Command: j m) 30. [White Balance] Red Offset (Command: s x) Adjusts the red gain value for white balance. Adjusts the red offset value for white balance. Transmission Transmission (j)(m)( )(Set ID)( )(Data)(Cr) (s)(x)( )(Set ID)( )(Data)(Cr) Data 00-FE: Red Gain 0-254 Data...
Page 109
33. [Backlight] (Command: m g) 36. [Tile Mode] Check (Command: d z) Adjusts the backlight brightness. Checks the tile mode. Transmission Transmission (m)(g)( )(Set ID)( )(Data)(Cr) (d)(z)( )(Set ID)( )(Data)(Cr) Data 00-64: Backlight 0-100 Data FF: Check Tile Mode Acknowledgment Acknowledgment (g)( )(set ID)()(OK/NG)(Data)(x) (z)( )(Set ID)( )(OK/NG)(Data1)(Data2)(Data3)(x)
Page 110
39. [DPM] (Command: f j) 42. [Fail Over] Mode (Command: m i) Sets the DPM(Display Power Management) function. Selects a sound mode. Transmission Transmission (f)(j)( )(Set ID)( )(Data)(Cr) (m)(i)( )(Set ID)( )(Data)(Cr) Data 00: [Off] Data 00: [Off] 04: 1 minute 01: [Auto] 05: 3 minutes 02: [User Setting]...
Page 111
44. Remote Control Key Lock (Command: t p) 46. Status Check (Command: s v) Configures the settings of the product's remote control key. Checks the current signal of the product. Transmission Transmission (t)(p)( )(Set ID)( )(Data)(Cr) (s)(v)( )(Set ID)( )(Data)( )(FF)(Cr) Data 00: Unlocks all keys Data...
Page 112
48. [PM Mode] (Command: s n, 0c) Data 09 (when checking the fan speed) Sets the PM mode. Acknowledgement Transmission (v)( )(Set ID)( )(OK/NG)(Data)(Data1_1)(Data1_2) (s)(n)( )(Set ID)( )(0c)( )(Data)(Cr) …(DataN_1)(DataN_2)(x) Data 00: [Power Off] (Basic) Data1_1:00~ff: First fan speed top 1 Byte 01: [Sustain Aspect Ratio] Data1_2: 00~ff: First fan speed bottom 1 Byte 02: [Screen Off]...
Page 113
50. [Network Setting] (Command: s n, 80 or 81 or 51. [Power On Status] (Command: t r) Sets the Power On status of the monitor. Configures network and DNS settings. Transmission Transmission (t)(r)( )(Set ID)( )(Data)(Cr) (s)(n)( )(Set ID)( )(Data1)( )(Data2)( ) Data 00: [LST(Last Status)] (Data3)( )(Data4)( )(Data5)(Cr)
Page 114
54. [Time Sync] (Command: s n, 16) 57. [External Input Rotation] (Command: s n, 85) Sets Time Sync. Sets the External Input Rotation feature. Transmission Transmission (s)(n)( )(Set ID)( )(1)(6)( )(Data)(Cr) (s)(n)( )(Set ID)( )(8)(5)( )(Data)(Cr) Data 00: [Off] Data 00: [Off] 01: [On] 01: 90 degrees...
Page 115
60. [Brightness Scheduling] (Command: s s) 61. [Multi Screen] Mode & Input (Command: x c) Sets Brightness Scheduling. Saves and controls Multi Screen modes and inputs. Transmission Transmission (s)(s)( )(Set ID)( )(Data1)( )(Data2)( )(Data3)(Cr) (x)(c)( )(Set ID)( )(Data1)( )(Data2)( )(Data3)( )(Data4) ( )(Data5)( )(Cr) Data 1 1.
Page 116
62. [Aspect Ratio] (Multi screen) (Command: x d) 65. Stop Video (Command: k x) Controls the aspect ratio of Multi Screen. Controls Stop Video. Transmission Transmission (x)(d)( )(Set ID)( )(Data1)( )(Data2)(Cr) (k)(x)( )(Set ID)( )(Data)(Cr) Data1 01: Controls the Main input Data 00: The Stop Video feature is on.
Page 117
69. [Holiday Setting] (Command: s n, 9b) 3. Deleting a Schedule E0: Deletes all holiday schedules Sets holidays. E1: Deletes the 1st holiday schedule Transmission E2: Deletes the 2nd holiday schedule 1. (s)(n)( )(Set ID)( )(9)(b)( ) E3: Deletes the 3rd holiday schedule (Data1)( )(Data2)( )(Data3)( ) E4: Deletes the 4th holiday schedule (Data4)( )(Data5)( )(Data6)(Cr)
Page 118
70. [ISM Method] (Command: s n, 9c) 73. [Wi-Fi Lock] (Command: s n, 9f) Sets UPnP.mode. Sets Wi-Fi Lock. Transmission Transmission (s)(n)( )(Set ID)( )(9)(c)( )(Data)(Cr) (s)(n)( )(Set ID)( )(9)(f)( )(Data)(Cr) Data 00: [Off] Data 00: Wi-Fi Unlock 01: [On] 01: Wi-Fi Lock Acknowledgment Acknowledgment...
Page 119
75. See [Backup via Storage] (Command: s n, a1) 76. [Digital Audio Input] (Command: s n, a2) Sets Backup via Storage. Sets Digital Audio Input. Transmission Transmission 1. (s)(n)( )(Set ID)( )(a)(1)( )(Data1)(Cr) (s)(n)( )(Set ID)( )(a)(2)( )(Data)(Cr) 2. (s)(n)( )(Set ID)( )(a)(1)( )(Data1)(Data2)(Cr) Data 00: Digital 1.
Page 120
79. [Natural Size] (Command: s n, a5) 82. [Audio Out] (Command: s n, aa) Sets the Natural Size feature. Sets Audio Out to Off/Variable/Fixed. Transmission Transmission (s)(n)( )(Set ID)( )(a)(5)( )(Data)(Cr) (s)(n)( )(Set ID)( )(a)(a)( )(Data)(Cr) Data 00-64: Natural Size 0 - 100 Data 00: [Off] 01: [Variable]...
Page 121
85. [Apply to all inputs] (Command: n, 52) 3. 01h to 0ch (Timer Power On days setting) 02: Repeat Daily Apply the video mode and low value of the current input to the same video value of all inputs. 03: Repeat from Monday to Friday 04: Repeat from Monday to Saturday Transmission 05: Repeat from Saturday to Sunday...
Page 122
87. [Time to OFF] Scheduling (Command: f e) 88. LCIN008 Control (Command: s n, b8) Sets Off Timer settings. It controls the LCIN008 device. Transmission Transmission (f)(e)( )(Set ID)( )(Data1)( )(Data2)( )(Data3)(Cr) (s)(n)( )(Set ID)( )(b)(8)( )(Data1)(Data2)(Cr) Data1 Data 1 00: LCIN008 Power 1.
Page 123
91. Change Setid (Command: j x) 94. [UHD Deep Color] (Command: s n, af) Changes and checks Setid. It sets the UHD Deep Color mode for each input. 1. When it is a general LED model Transmission Transmission (s)(n)( )(Set ID)( )(a)(f)( )(Data1)( )(Data2)(Cr) (j)(x)( )(Set ID)( )(Data1)( )(Data2)(Cr) Data1 70: DVI-D Data1 Data2 : 00 01 ~ 03 e8 (1~1000)
Page 124
96. [Input Manager] (Command: s n, b1) 99. [Scan Inversion] (Command: s n, 87) It sets labels by input. It controls the on/off status of Scan Inversion. Transmission Transmission (s)(n)( )(Set ID)( )(b)(1)( )(Data1)( )(Data2)(Cr) (s)(n)( )(Set ID)( )(8)(7)( )(Data)(Cr) Data1 90: HDMI1 Data 00: Off...
Page 125
102. Read Brightness Value (Command: m u) 105. [HDR Picture Mode] (Command: s n, c4) Checks the brightness value. Selects a HDR Picture Mode. Transmission Transmission (m)(u)( )(Set ID)( )(FF)(Cr) (s)(n)( )(Set ID)( )(c)(4)( )(Data)(Cr) Data 00: Mall/QSR 01: General Acknowledgment 02: Gov./Corp.
Page 126
108. [USB2 to HDBaseT] (Command: s n, c3) Sets USB2 to HDBaseT. Transmission (s)(n)( )(Set ID)( )(c)(3)( )(Data)(Cr) Data 00: [Off] 01: [On] Acknowledgment (n)( )(Set ID)( )(OK/NG)(c)(3)(Data)(x) * This feature may not be available for all models. 109. [Change Password] (Command: s n, a7) Changes password.