Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for ATS AE14-503J Series
- Page 1 FN:503JMAN2.DOC AE14-503J SERIES PRODUCTION DISPLAY SYSTEM...
-
Page 2: Specifications
This manual will use the term “the AE DEVICE”, in some cases to cover all versions of displays. The model numbers of the AE14-503J Series are derived from the digit size and the number of digits in each line of the display, followed by the suffix 503J. For example the AE14-503J is a One Inch, Four-Digit display. - Page 3 (up to 32) AE14-503J’s. AEQuery software and an RS232/485 I/O Adapter (ATS P/N: 9200-0509) are required. The software uses the computer’s RS232 port to send and receive data from up to 32 individually addressed AE Devices. AEQuery can store the Goal and Actual counts, Interval and Actual switch settings, and run time of each AE Device on the system.
-
Page 4: Installation
White wire, and connect the other side of the switch to the Black wire. TYPICAL WIRING EXAMPLES : COUNT AND RUN/HOLD INPUTS For the RS485 I/O Interface wiring and operation refer to the “RS485 I/O Interface” section of this manual. APPLIED TECHNICAL SYSTEMS PAGE 3 WWW.ATS-USA.COM... -
Page 5: Operation
RS485 I/O INTERFACE The RS485 I/O Interface for the AE14-503J, allows a host device such as a PC to communicate with one or more (up to 32) AE14-503J’s and/or other AEXX-503J devices. AEQuery software APPLIED TECHNICAL SYSTEMS PAGE 4 WWW.ATS-USA.COM... - Page 6 This feature is factory installed in the AE14-503J. Connection is required from terminal 3 (A) and 4 (B) on TB2 to terminals A and B on the RS232/485 I/O Adapter (ATS P/N: 9200-0509). Up to 32 AE14-503J’s, and/or other AEXX-503J devices can be connected in parallel (multi-dropped) to a single computer via the RS232/485 Adapter.
- Page 7 Disk 2 again to continue setup. Once the copying of files from the disks is complete, Windows will begin Setup Wizard. The Setup Wizard will allow you to create your own directory to install the AEQuery software or it will default to the following directory C:\ProgramFiles\AEQuery\. APPLIED TECHNICAL SYSTEMS PAGE 6 WWW.ATS-USA.COM...
- Page 8 Click “Setup” again to change the RTS Polarity if necessary. Some RS485 adapters use Positive True logic and while others use Negative True logic for the RTS signal. The ATS adapter (P/N 9200-0509) is a negative true device. Other approved adapters may use positive true logic device.
- Page 9 You will be prompted for the address of the unit that you want to clear. To clear the run time (reset it to zero) of all units (addresses 1 – 32): 1. Click “Utilities”. 2. Click “Clear Run Time”. 3. Click “Clear All Units”. APPLIED TECHNICAL SYSTEMS PAGE 8 WWW.ATS-USA.COM...
- Page 10 Note: The totals will be calculated from the addresses specified in the Address Group. User may view the “Total” line on the AE4X46-503J Remote Display or the bottom border of the AEQuery program window to see the calculated totals appear at the specified interval. APPLIED TECHNICAL SYSTEMS PAGE 9 WWW.ATS-USA.COM...
-
Page 11: Technical Support
APPLIED TECHNICAL SYSTEMS WARRANTY POLICY ATS warrants its products to be free of defects in material and workmanship for a period of 24 months from the date of purchase. ATS will repair or replace any product returned to its authorized factory service center within the warranty period so long as there is no evidence that the product has been abused, misused, damaged by lightning, overloads of any kind or water, or altered in any way.
Need help?
Do you have a question about the AE14-503J Series and is the answer not in the manual?
Questions and answers