Advertisement
Quick Links
Santa Belle Gazebo
Style # L-GZ089PST
Recommended persons for safe assembly: 4.
CONGRATULATIONS – You've purchased a fine item from The
Home Depot.
Our clear, easy to follow; step by step instructions will guide
you through the project from start to finish. Feel confident that
this will be a fun and rewarding project. The final product will be
a quality piece that will go together smoothly and give years of
enjoyment.
All you will need is a screwdriver, a hammer, and a ladder not
Advertisement
Summary of Contents for SNOWJOE Sunjoy Santa Belle
- Page 1 Santa Belle Gazebo Style # L-GZ089PST Recommended persons for safe assembly: 4. CONGRATULATIONS – You’ve purchased a fine item from The Home Depot. Our clear, easy to follow; step by step instructions will guide you through the project from start to finish. Feel confident that this will be a fun and rewarding project.
- Page 2 lower than 2m (about 6.6 feet). If you have any questions just call 866-578-6569. Please refer to the DPCI code about when calling. Step Identification For ease of identification all parts labeled correspond Step number in which the part is used.
- Page 3 damage will occur to the structure. Never barbecue under this gazebo or use lanterns that contain naked flames. This package contains small items and plastic bags that should be kept away from children. Ensure that any connectors & poles are firmly secured in position fully. It is important to do so before use so as to avoid collapsing or damage to the item, which could result in injury.
- Page 5 Fig.1: Insert one end of 1B into 1A; do the same for 1E and 1F. Fig.2: Insert one end of 1C and 1G into 1D separately. Fig.3: Connect the other ends of the mutually inserted bars (the ones inserted in Fig.1 and Fig.
- Page 7 Fig.4＆Fig.5＆Fig.6＆Fig.7: .① Insert 1K into1L; .② Insert one end of 1M into 1L, and then insert the other end of it into 1J（1I）; .③ Insert one end of 1Ointo 1L, and the other end into the hole in 1C; .④ Insert one end of 1J into 1L and then the other end into the hole in 1A.
- Page 8 Fig.8: Screw off the bolt AA, washer BB and nut CC which have been pre-assembled in 1K, and use them to fix two 1Ns with 1K; Fig.9: Insert the other end of 1N into 1D; Fig.10: Fasten 1A & 1B with 1E & 1F together by 1P At the end of this step, you will get the whole top frame ready as below figure shows.
- Page 9 Fig.11.1 & Fig. 11.2 ：Insert one end of four 2As into 2Bs separately, then lift the top and insert the other end of 2A into 1I, 1J and 1D separately.（Get 4 persons here at least for this step）. By doing this, you reach the step of Fig. 11 now. Fig.11.3：Peg stakes GG into the ground to secure the gazebo.
- Page 10 Fig.12.1 & Fig. 12.2 ： ① Put on mosquito net 2C into the top frame bars 1E, 1F and 1G, using plastic rings 2D; ②Tie one end of the rope 2F to the corner edge of the canopy; Loop the other end of the rope through the hole of rope peg 2E insert rope peg 2E into the ground.
- Page 11 hardware is not covered. Proof of purchase (dated register receipt) is required for warranty claims. Warranty is to the original purchaser and is non-transferable. Any replacement of warranted items will be in the original style and color, or a similar style and color if the original is unavailable or has been discontinued.
- Page 12 91706...