Advertisement
2. INTRODUCTION & SPECIFICATIONS
Patented eccentric assembly with sealed double bearings give 8mm orbital
diameter. Variable speed control from 2500-6500rpm. Alloy bevel gear head with
smooth composite motor housing for added comfort. Side mounted slider type
power control with power lock. Supplied with Ø150mm hook & loop pad and side
handle.
2.1.
Specification:
Power . . . . . . . . . . . . . 230V - 500W
No load speed . . . . 2500 - 6500rpm
Orbit size . . . . . . . . . . . . . . . . .8mm
Pad . . . . . . . . . . . . . . . . . . Ø150mm
Thread . . . . . . . . . . . . . . . 5/16"UNF
Weight . . . . . . . . . . . . . . . . . . 2.2 kg
Vibration . . . . . . . . . . . . . .21.15m/s²
Sound power level . . . . . . . . 90.7dB
Sound pressure . . . . . . . . . . 79.7dB
3. ASSEMBLY
3.1.
Assembly
WARNING! DO NOT plug sander into the mains power supply before it is fully
assembled.
Unpack the sander and check contents. The contents should include a spanner,
side handle and backing pad, should there be any damaged or missing parts con-
tact your supplier immediately. Screw handle (fig.1.2) into the hole (right or left
side, as required) in the head. Screw the sanding pad onto the spindle (fig.1.3).
To remove pad, hold spindle with the spanner supplied whilst unscrewing the pad.
4. OPERATING INSTRUCTIONS
WARNING! Before use, ensure that you have read and understood
Section 1 Safety Instructions.
4.1.
Attach the correctly rated sanding disc (not supplied) to the sanding pad.
4.2.
Plug the sander into the mains power supply.
4.3.
Ensure that the speed scroll switch is set to the lowest setting before
starting the sander (fig.1.4). Grip the side handle and turn on by pushing
switch (fig.1.1) forward. Let go of the switch and the machine will continue
running. Increase the speed of the sander using the variable switch
located at the rear of the sander (fig.1.4).
4.4.
To release the switch, and stop the sander, press down on the rear section
of the switch - it will spring to the Off position.
4.5.
Ensure that the above features are working correctly prior to use.
Note: The sander is designed for dry use only. DO NOT use with water or any
other liquids.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
PADS: DAS150T.V4
PTC/150A . . . . . . . . . . . . Stick-on (Firm)
PTC/150SA (supplied) . . . Stick-on(Soft)
PTC/150VA . . . . . . . . . . . Hook & Loop
fig.1
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
Original Language Version
5. MAINTENANCE
WARNING! Disconnect sander from power supply before changing
accessories, servicing or performing maintenance.
Replace or repair any damaged parts. Use genuine parts only,
unauthorised parts may be dangerous and will invalidate the warranty.
5.1.
After each 50 hours use (or as required), remove dust by blowing
air through the side vents and around the pad bearing. Periodic cleaning
will prolong machine life.
5.2.
Change pads when required. Ensure pad and disc RPM ratings are equal
to, or exceed the machine rating. If the disc becomes unbalanced, it will
cause the bearings to wear.
5.3.
When not in use store in a safe, dry, childproof location.
5.4.
Check brushes every 200 hours of use. To access the brushes refer to
fig.2. Undo the screw in the end of the motor casing (fig.2.1) and slide
back the cover (fig.2.2). Using a small screwdriver lift the brush spring to
one side (fig.2.3) and slide the brush out of its holder (fig.2.4). If the brush
is worn to half of its original length it should be renewed. Using thin nosed
pliers pull the brush connector off its terminal (fig.2.5). Slide the new brush
into its holder. Slide the connector onto the terminal (fig.2.5). Position the
spring so that it bears down onto the end of the brush. Remember to
renew brushes as a pair.
Slide rear cover back into place and retain it with the screw.
5.5.
All other service and maintenance must be carried out by an authorised
service agent.
01284 757500
01284 703534
fig.2
www.sealey.co.uk
Web
sales@sealey.co.uk
email
DAS150T.V4
Issue: 2 - 12/10/09
Advertisement
