Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ADENDORFF MAC AFRIC SDRILC-024
Summary of Contents for ADENDORFF MAC AFRIC SDRILC-024
- Page 2 GENERAL POWER TOOL SAFETY WARNINGS 9. If operating a power in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock. (For All Power Tools) NOTE: The term “residual current device (RCD)” may be replaced by the term “ground Failure to follow all WARNING! Read and understand all instructions.
-
Page 3: Specifications
controlled with the switch is dangerous and must be repaired. Service 19. Disconnect the plug from the power source and/or the battery from the power tool 28. Have your power tool serviced by a qualified repair person using only identical Such This will ensure that the safety of the power tool is maintained. - Page 4 2. Check the tool and battery carefully before putting it into use. Stop operation immediately Always set the reversing switch lever in the central position (lock the switch) and when malfunctions be found and send the tool to be repaired by qualified serviceman. Do remove the battery cartridge before tool change, inspection, maintenance, not open the tool yourself.
-
Page 5: Instructions For Operation
16. Do not expose battery cartridge to rain, snow or wet conditions. INSTRUCTIONS FOR OPERATION 17. Store battery cartridge properly: Installing or Removing the Battery a) Store the battery after it is fully charged CAUTION: b) Store the battery only within a temperature range between 0℃ and 45℃. Too hot or too cold may damage the battery. - Page 6 Battery Indicator Light 2. Insert the battery pack fully into the battery charger and the charger starts CAUTION: charging. The four charging lights may flash in red color The battery charger can detect some sort of if the tool is overheated or overloaded. As failure caused by the battery and indicates by temperature recovers or over-load protection the statuses of the red and green indicator...
- Page 7 Clockwise Rotation FFCL18-01 SCHARG-001 Model FFCL18-05 FFCL18-03 (FFCL18-04) Depress the reversing switch lever from side B Input Voltage (AC) 220-240V 110-240V 220-240V to side A for clockwise rotation. (view Charging Current 3.0A 2.0A forwards). Input Power Frequency 50-60Hz Counterclockwise Rotation Applicable Battery Cartridge Voltage (DC) Depress the reversing switch lever from side A 4.0Ah...
- Page 8 Auxiliary Handle Bit Angle When using the tool for demolition operation, to Always use the auxiliary handle to ensure operating change the drill angle, turn the operating mode safety. Make sure that the auxiliary handle is on the selector (without pressing the lock button), and appointed place of the tool, and is tightened securely.
-
Page 9: Maintenance And Inspection
Deep Discharging Protection Set the operating mode selector to the symbol, and position the bit at the desired location for the hole, then pull the switch trigger. The tool is equipped with a protective circuit to protect the battery against deep discharging. Eccentricity in the bit rotation may occur while operating the tool with no load. - Page 10 EXPLANATION OF GENERAL VIEW Dustproof Cover O Ring Circlip for Shaft O Ring Washer Adaptor Sleeve Locking Sleeve Roundwire Snap Ring for Hole Roundwire Snap Ring Clamping Ring Clamping Ring Washer Steel Ball Clutch Spring Dead Plate Clutch Gear Compression Spring Clutch Plate Lock Pin O Ring...
- Page 11 EXPLANATION OF GENERAL VIEW Ball Bearing Auxiliary Handle Armature Assembly Left-half Handle Bearing Shim Right-half Handle Ball Bearing Pan Head Tapping Screw Stator Assembly Operating Mode Selector Rear Cover O Ring Pan Head Tapping Screw Selector Lever Spline Shaft Spring Ball Bearing Slider Retainer...
Need help?
Do you have a question about the MAC AFRIC SDRILC-024 and is the answer not in the manual?
Questions and answers