Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Topens MultiRuta CASAR 800
Summary of Contents for Topens MultiRuta CASAR 800
- Page 1 GARAGE DOOR OPENER User’s Manual Model: CASAR 800 TOPENS Website www.topens.com Email: support@topens.com ★ Please read and follow all warnings, precautions and instructions before installation and use. ★ Save this manual. C030554 VER 21a...
- Page 2 Visit: www.topens.com Please record the product model, your email address etc. in the spaces provided below. Refer to this list when contacting TOPENS for technical service or assistance with your automatic gate opener. Where did you purchase? (Amazon.com; Amazon.ca: Amazon.co.uk, Amazon.de; Other, Please...
-
Page 3: Table Of Contents
Table of Contents 1. Before You Begin ............................4 1.1 Door Types ..............................4 1.2 Tools Required for Installation........................5 1.3 Accessories Connection ..........................5 1.4 Completed Installation ..........................6 2. ASSEMBLY SECTION ..........................7 2.1 Open the Chain Package ..........................7 2.2 Assemble the Driving Assembly ....................... - Page 4 ·Stop in case of obstruction during gate opening ·Reverse in case of obstruction during gate closing ·Soft start and soft stop (each soft period can Not be adjusted). Optional Accessories Parts List (Available at TOPENS Store) TC186-R WiFi TC186 WiFi...
- Page 5 Replacement Parts CKMJ2A Control Board WARNING: Changes or modifications not expressly specified by this user manual, TOPENS could void the warranty of this equipment.
- Page 6 Start by Reading These Important Safety Rules These safety alert symbols mean WARNING－a personal safety or property damage instruction. Read these instructions carefully. This garage door opener is designed and tested to offer reasonable safe service provided it is installed and operated in strict accordance with the following safety rules.
-
Page 7: Before You Begin
1. Before You Begin Look at the wall or ceiling above the garage door. The header bracket MUST be securely fastened to structural supports. It is easier to fit this door opener while the garage door is in the colsed position and before you set the control board. -
Page 8: Tools Required For Installation
1.2 Tools Required for Installation 1.3 Accessories Connection There is Connecting Wire Terminal in the unit’s side as picture 3, the function is as follows: Terminal 1 for DOOR CONTROL BUTTON Terminal 2 for DOOR CONTROL BUTTON Terminal 3 for SAFETY PHOTOCELL BEAM (SPB) Terminal 4 for SAFETY PHOTOCELL BEAM (SPB) Terminal 5 for positive of Additional 24VDC Power Source Terminal 6 for negative of Additional 24VDC Power Source... -
Page 9: Completed Installation
1.4 Completed Installation As you proceed with the assembly, installation and adjustment procedures in this manual, you may find it helpful to refer back to this illustration of a completed installation. Name Name Header Sleeve Manual Release Rope & Handle Idler Pulley Bracket Curved Door Arm Trolley... -
Page 10: Assembly Section
2. ASSEMBLY SECTION 2.1 Open the Chain Package Drill the one end of chain through the space between the pulley bracket (1) and Idler pulley (2), wrapping it round the idler pulley (2). Then connect live knots in both ends of the Chain to both ends of the chain connector (3). -
Page 11: Fasten Rail To Opener And Install Chain
Wear protective gloves when assemble the rail to protect your hands from possible injury from the edge of the rail. Place rail pieces (1) on flat surface for assembly. All four rail sections are interchangeable. Slide rail brace (2) onto rail section. Connect rail by sliding rail brace onto next rail section. Tap rail assembly on piece of wood until rail sections are flush. -
Page 12: Attach Sprocket Cover
damage to opener. 2.5 Attach Sprocket Cover Place sprocket cover (1) on top of the opener (2), secure with screws (3). 2.6 Install Header Sleeve and Tighten Chain Slide header sleeve (1) onto rail. Slide flat washer (3), spring (2) and washer (3) onto carriage bolt (4). Thread nut (5) onto carriage bolt until finger tight. -
Page 13: Installation Section
3. INSTALLATION SECTION Wear protective goggles when working overhead to protect your eyes from injury. Disengage all existing garage door locks to avoid damage to garage door. To avoid serious personal injury from entanglement, remove all ropes connected to garage door before installing opener. -
Page 14: Install The Header Bracket
3.2 Install the Header Bracket NOTE: Refer to vertical center and horizontal lines created in step 10 for proper placement of header bracket. A. Wall Mount: Center the header bracket (1) on the vertical center line (2) with the bottom edge of the header bracket on the horizontal line (4) (with the arrow pointing toward the ceiling). -
Page 15: Attach Rail To Header Bracket
3.3 Attach Rail to Header Bracket Position opener on garage floor below the header bracket. Use packing material to protect the cover. Raise rail until holes in the header sleeve and holes in the header bracket align. Join with clevis pin (1). Insert “R”... -
Page 16: Hang Opener
3.5 Hang Opener Bend Hanging Brackets (1) so they are flat against ceiling. Measure distance from Header Bracket to Ceiling Mounting Bracket Bolts (4). Mark length on ceiling starting at the Header Wall, along this point is where the unit will be mounted. Lift door to full open position, rest opener on door. Slide Hanging Brackets on to Ceiling Mounting Bracket Bolts (4) on the opener. -
Page 17: Assemble Door Arm (Not Bow Arm)
Sectional and One-Piece Door Installation Procedure: Door bracket has left and right side fastening holes. If your installation requires top and bottom fastening holes use both the door bracket and door bracket plate as shown. Center door bracket (with or without door bracket plate, as required) at the top inside face of door as shown. Mark holes. -
Page 18: Install Door Control (Optional)
3.8 Install Door Control (Optional) Locate door control where the garage door is visible, away from door and door hardware and out of the reach of children. Mount at least 5 feet (1.5 meters) above the floor. Serious personal injury from a moving garage door may result from misuse of opener. Do not allow children to operate the door control or remote control transmitter. -
Page 19: Install The Safety Photocell Beam (Spb) System (Optional)
3.9 Install the Safety Photocell Beam (SPB) System (Optional) 1. Position the transmitter and receiver at a height of 30-40cm (11.8”-15.7”) from the ground. For the best protection, please DON’T exceed the height of 40cm (15.7”). 2.If the TC102 photo eye beam sensor is connected，use a 2-core cable to connect the “+ ~” terminal of the photocell’s emitter to the terminal 5, the “- ~”... -
Page 20: Adjustment Section
250pcs remotes to be programmed for the opener. TOPENS ERM12 Universal External Receiver is available at TOPENS Store. TOPENS ERM12 Universal External Receiver is also compatible with other brand swing gate opener, sliding gate opener and garage door opener. -
Page 21: Setting The Limits
4.2 Setting the Limits 1. Press and hold SET button for more than 4 seconds. The Digital Display indicates “1” (Pic.4.2-1). Press and release SET button again, “1” flashes in the Digital Display (Pic. 4.2-2). Now the unit enters into Limit Setting Mode. 2. -
Page 22: Setting The Open Force
4.3 Setting the Open Force 1. Press and hold SET button for more than 4 seconds. The Digital Display indicates “1” (Skip if continuing Open Force Set after the Limits Set is finished). 2. Continually press UP button until the Digital Display indicates “3”... -
Page 23: Setting The Automatic Closing Time
4.5 Setting the Automatic Closing Time 1. Press and hold SET button for more than 4 seconds. The Digital Display indicates “1” (Skip if continuing Closing Time Set after the Close Force Set is finished). 2. Press UP button and choose figure “5” (Pic.4.5-1). Press and release SET button. -
Page 24: Test The Safety Reverse System（Very Important
4.7 Test the Safety Reverse System（Very Important） The safety reverse system test is important. Garage door must reverse on contact with a 100mm (4”) obstacle laid flat on the floor. Failure to properly adjust opener may result in serious personal injury from a closing garage door. -
Page 25: Install Hlr01 Homelink Remote Control Kit (Optional)
4.9 Install HLR01 HomeLink Remote Control Kit (Optional) Use a 2-core cable to connect the “DC+” terminal of the HLR01 to the terminal 5, the “DC－” terminal to the terminal 6. Use another 2-core cable to connect the “NO1” terminal of the HLR01 to the terminal 1, the “COM1” terminal to the terminal 2. - Page 26 • Replace battery if necessary. • If you have two or more remotes and only one operates, review Program Your Opener and Remote step 4.1. Remote has short range: • Is battery installed? • Change the location of the remote control on the car. •...
-
Page 27: Care Of Your Opener
• Garage door springs are broken. SEE ABOVE. • If problem occurs on first operation of opener, door is locked. Disable door lock. Repeat safety reverse test after adjustment is complete. Opener won't activate due to power failure: • Pull manual release rope and handle down and back to disconnect trolley. Door can be opened and closed manually. -
Page 28: Quick-Setting Guide
5. Quick-Setting Guide 5.1 Program your Opener & Remote 5.2 To Erase all remote Control codes... -
Page 29: Unit Setting
5.3 Unit Setting... - Page 33 Your comments and suggestions are important to us as they help us provide the best possible service. Should you have any need to contact us, the info below will help you get in touch: TOPENS Website www.topens.com Contact Us: E-mail: support@topens.com Kindly include your Product Model, Purchasing Date &...
Need help?
Do you have a question about the MultiRuta CASAR 800 and is the answer not in the manual?
Questions and answers
where can i buy a new circuit board for the casar 800 garage door opener it stoped working after a week force adjustment stoped working