Directed MA3 2018 Installation Manual
  1. Manuals
  2. Brands
  3. Directed Manuals
  4. Automobile
  5. MA3 2018
  6. Installation manual
Directed MA3 2018 Installation Manual

Directed MA3 2018 Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
INSTALLATION GUIDE
MA3
Designed by Installers for Installers
© 2018 Directed, Vista CA
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle's
electrical system and components.
2018-03-06
Directed Digital
Solutions

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MA3 2018 and is the answer not in the manual?

Questions and answers

Summary of Contents for Directed MA3 2018

  • Page 1 Solutions Designed by Installers for Installers © 2018 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle’s electrical system and components.

  • Page 2: Table Of Contents

    Contents Warning! Safety first ........................3 Introduction ............................ 4 Pre-installation and application warnings ..................4 Vehicle application guide ......................5 Wiring connections ......................... 6 Main power harness (H1), 12-pin thick gauge connector ............... 6 Auxiliary output harness (H2), 16-pin black connector ..............6 Analog harness (H3), 18-pin white connector ................

  • Page 3: Warning! Safety First

    The following safety warnings must be observed at all times: • Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. • When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an area that does not have adequate ventilation.

  • Page 4: Introduction

    Introduction The MA3 firmware for Directed Digital Solutions is compatible with specific Mazda, Scion and Toyota vehicles. It is a complete solution for remote start, security (if applicable), bypass interface, and convenience. This guide provides information on the installation of the module using MA3. If you would prefer using this system as a digital solution, go to www.directechs.com and search for the make, model and year of the vehicle.

  • Page 5: Vehicle Application Guide

    PK: Transponder & Immobilizer Override DL: OE Door Lock & Alarm Controls FOB: Sync CAN Interface w/ FOB Remote RS: Remote Start & Engine Controls SS: Integrated Security & Monitoring ST: Function/Feature Status Directed Digital Solutions MA3 © 2018-03-06 Directed. All rights reserved.

  • Page 6: Wiring Connections

    If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary. Directed Digital Solutions MA3 © 2018-03-06 Directed. All rights reserved.

  • Page 7: Analog Harness (H3), 18-Pin White Connector

    These connections are only required if the corresponding statuses are not supported by the firmware. See "Vehicle application guide" on page 5 for a list of compatible features. Directed Digital Solutions MA3 © 2018-03-06 Directed. All rights reserved.

  • Page 8: Installation (Wiring Diagrams & Vehicle Wiring Reference Charts)

    Yellow: Parking Light Interrupt (conn.side) THMAC1 (-) Trunk Release Output: Red/White (optional (+) Siren Output: Brown (-) Trunk Release: T-Harness) White/Blue, pin 3 Siren Trunk Release Switch (White conn. in driver dash) Directed Digital Solutions MA3 © 2018-03-06 Directed. All rights reserved.

  • Page 9: Type 1

    (+) 12V: White, pin 1 Fuse Box (White conn. at drivers kick) (+) Trunk Release Actuator: Green, pin 2 1112 Trunk Release Actuator (Blue conn. at left rear quarter panel) Directed Digital Solutions MA3 © 2018-03-06 Directed. All rights reserved.
  • Page 10 Parking light assembly switch. White Door Lock [6] White/Green Driver kick, door harness. White Trunk Release Actuator Green BCM in left rear quarter panel. Blue Trunk Release [7] White/Blue Trunk release switch. White Directed Digital Solutions MA3 © 2018-03-06 Directed. All rights reserved.
  • Page 11 Parking light assembly switch. White Door Lock [6] White/Green Driver kick, door harness. White Trunk Release Actuator Green BCM in left rear quarter panel. Blue Trunk Release [7] White/Blue Trunk release switch. White Directed Digital Solutions MA3 © 2018-03-06 Directed. All rights reserved.
  • Page 12 Yellow: Parking Light Interrupt (conn.side) THMAC1 (-) Trunk Release Output: Red/White (optional (+) Siren Output: Brown (-) Trunk Release: T-Harness) Green/Red, pin 1 2 3 4 Siren Trunk Release Switch Directed Digital Solutions MA3 © 2018-03-06 Directed. All rights reserved.
  • Page 13 White, pin 1 (+) Trunk Release Actuator: Green or Brown, pin 2 Fuse Box (White conn. at drivers kick) 1112 Trunk Release Actuator (Blue conn. at left rear quarter panel) Directed Digital Solutions MA3 © 2018-03-06 Directed. All rights reserved.
  • Page 14 Door Lock [6] White/Green Driver kick, door harness. White Trunk Release Actuator Green or Brown BCM in left rear quarter panel. Blue Trunk Release [7] Green/Red Trunk release switch. White Directed Digital Solutions MA3 © 2018-03-06 Directed. All rights reserved.

  • Page 15: Type 3

    Yellow: Parking Light Interrupt (conn.side) THMAC1 (-) Trunk Release Output: Red/White (optional (+) Siren Output: Brown (-) Trunk Release: T-Harness) White, pin 1 2 3 4 Siren Trunk Release Switch Directed Digital Solutions MA3 © 2018-03-06 Directed. All rights reserved.
  • Page 16 (+) 12V: White, pin 1 (+) Trunk Release Actuator: Fuse Box Blue, pin 2 (White conn. at drivers kick) 1112 Trunk Release Actuator (Blue conn. at left rear quarter panel) Directed Digital Solutions MA3 © 2018-03-06 Directed. All rights reserved.
  • Page 17 White Door Lock [6] Lt. Blue Driver kick, door harness. White Trunk Release Actuator Blue BCM in left rear quarter panel. Blue Trunk Release [7] White Trunk release switch. White Directed Digital Solutions MA3 © 2018-03-06 Directed. All rights reserved.

  • Page 18: Type 4 With T-Harness (Thmac1) (Rev-1)

    (+) Trunk Shunt Input: Gray/Black (White conn. at drivers kick) Interrupt (vehicle side) (-) Trunk Release Output: Red/White Yellow: Parking Light Interrupt (conn. side) THMAC1 (+) Siren Output: Brown (optional T-Harness) Siren Directed Digital Solutions MA3 © 2018-03-06 Directed. All rights reserved.

  • Page 19: Type 4

    Optional Siren (+) 12V: White, (+) Trunk Release Actuator: White, pin 4 pin 1 Fuse Box (White conn. at drivers kick) ESU (Electrical Supply Unit) (White conn. at drivers kick) Directed Digital Solutions MA3 © 2018-03-06 Directed. All rights reserved.
  • Page 20 Door Lock [6] Brown BCM bottom left plug. White Trunk Release Actuator White ESU (Electrical Supply Unit) in drivers kick panel. White Trunk Release [7] BCM above driver kick panel. White Directed Digital Solutions MA3 © 2018-03-06 Directed. All rights reserved.

  • Page 21: Type 5

    2 & 8: White/Brown: (+) Brake Output ESU (Electrical Supply Unit) 1 & 7: White: (+) 12V Input (White conn. at drivers kick) (+) 12V: White, pin 1 Fuse Box (White conn. at drivers kick) Directed Digital Solutions MA3 © 2018-03-06 Directed. All rights reserved.
  • Page 22 Parking Lights Blue Parking light assembly switch. White Parking Lights Interrupt Black Parking light assembly switch. White Trunk Release Actuator White ESU (Electrical Supply Unit) in drivers kick panel. White Directed Digital Solutions MA3 © 2018-03-06 Directed. All rights reserved.

  • Page 23: Accessing The Parking Light Circuit

    BACK Remove the battery from the OEM Remote. Make 4-6 loops and fasten to the back of the OEM remote (over the internal transponder) as shown in the diagram. Directed Digital Solutions MA3 © 2018-03-06 Directed. All rights reserved.

  • Page 24: Connecting The Module

    Manual or automatic transmission selection The yellow loop on the Directed Digital Solutions controls which transmission type the unit is configured for. The state of the loop (uncut or cut) when the main module is powered up will determine which type is selected.

  • Page 25: Rf Systems

    When flashing the Directed Digital Solutions, make sure to pick the remote you will be using. This way the main module will have the necessary firmware to interact with the remote and Control Center (antenna) combination.

  • Page 26: Module Programming

    Connect all but the 12-pin harness Connect all the harnesses to the Directed Digital Solutions, EXCEPT the 12-pin main power harness. Connect the 12-pin main power harness, and wait until the LED turns ON solid red.
  • Page 27 Connect all but the 12-pin harness Connect all the harnesses to the Directed Digital Solutions, EXCEPT the 12-pin main power harness. Must be connected LAST Connect the 12-pin main power harness, and wait until the LED turns ON solid red.

  • Page 28: Led Diagnostics And Troubleshooting

    External module synchronization Description Troubleshooting OBDII feature not supported. The diagnostic data bus was not detected, therefore the SmartStart features will be limited. (Flashes red, red, then orange) x 10 Directed Digital Solutions MA3 © 2018-03-06 Directed. All rights reserved.
  • Page 29 The vehicle was detected as moving, which prevents the system from shutting it down. Flashes red x 4 Analog error codes Description Troubleshooting DEI feature error. A feature config file mismatch was detected. Please contact Technical Support. Flashes red, green & orange Directed Digital Solutions MA3 © 2018-03-06 Directed. All rights reserved.

  • Page 30: Soft Reset

    A module reset will only erase the steps performed in "Module programming" on page 26. The firmware and settings flashed to the module will not be affected. Connect all but the If required for your installation, connect all the harnesses to the Directed Digital Solutions, 12-pin harness EXCEPT the 12-pin main power harness. Press and hold the programming button, then connect the 12-pin harness to the module.

  • Page 31: Learning The Tach (Not Needed With Virtual Tach)

    Important! After successfully learning Virtual Tach, a small minority of vehicle starters may over crank or under crank during remote start. Use the VirtualTach Fine tune feature in the configuration wizard to adjust the starter output time in 50mS increments to compensate for such an occurrence. Directed Digital Solutions MA3 © 2018-03-06 Directed. All rights reserved.

  • Page 32: Limited Lifetime Consumer Warranty

    Directed dealer, the unit was professionally installed and serviced by an authorized Directed dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer’s name, telephone number and address;...

  • Page 33: Quick Reference Guide

    Stop the vehicle in a safe parking spot and put the gear in gear in Park (P). Park This system is compatible with Directed SmartStart. For a complete list of supported features, please visit www.mysmartstart.com. Press the Remote Start button on the transmitter.* 14:36 &...
  • Page 34 The application enables a “Cloud-Connected Car” like never before, providing 2-way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet.

Table of Contents