Page 2
11. Choke lever 5. Right Handle 12. Recoil starter 6. Throttle Trigger 13. Fuel Tank 7. Throttle lever 2. Specifications ----------------------------------------------------------------------------------------------------- XT-BC508-1 Model no 1E43F-B,air-cooled, 2-stroke Engine Engine type displacement 50.8 cm³ Maximum engine power 1.7 kW Max rotational frequency of the spindle...
Brush cutter: 113,16 dB(A) K=3 dB(A); Grass trimmer: 113,99 dB(A) K=3 dB(A) Sound power level, Lwa : 117 dB(A), k=3 dB(A) Guaranteed sound power level, L Brush cutter: 6,736 m/s² Grass trimmer: 9,185 m/s² K=1,5 m/s² Vibration level Overall size(LxWxH) 1900x650x260 mm 2T: 305mm*1,6 mm Metal blade...
Page 4
Wear head, eye and ear Top speed of blade is 7100 protection. Wear protective gloves. Keep all children, bystanders and helpers 15 meters away from the brush cutter Wear safety footwear The guaranteed noise level Danger: Toughing With this symbol rotating blade manufacturer confirms that...
Page 5
replace as necessary before using the machine. DO NOT USE any attachment with this power head other than the ones recommended by our company. Serious injury to the operator or bystanders could result as well as damage to the machine. •...
Page 6
• Pay attention to loosening and overheating of parts. If there is any abnormality of the machine, stop operation immediately and check the machine carefully. If necessary, have the machine serviced by an authorized dealer. Never continue to operate a machine which may be malfunctioning. •...
Page 7
• Check each time before and after use, after a fall or other impacts to identify any significant damage. Do not use the tool in case of damage. Bring it to a qualified service agent for inspection and reparation. •...
Page 8
color changes or skin condition. These symptoms usually appear on the fingers, hands or wrists. Risk increases at low temperatures. Intended use This machine can be used with the cutting wire as a trimmer for cutting grass and weeds of small thickness and in small quantity and with the cutting blade as a brush cutter for cutting denser vegetation.
Page 9
■ INSTALLING RIGHT AND LEFT HANDLE (01) 1. Loose the bolt C and nut D from the right handle. 2. Insert the handle pipe B into right handle A, lock the bolt C and nut A securely. ■ INSTALLING HANDLE (02) 1.
2. Mount the trimmer head (8) on the axle. Fasten tightly anti-clockwise. NOTE (06) Before using the trimmer head, mount the trimmer knife (E) to protection shield (F) with 3 screws. When the machines is running, tap the trimmer head on the ground, and trimmer line will come out automatically.
WARNING • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. • Wipe up all spills before starting the engine. • Make sure to stop the engine and allow it cool before refueling the unit. •...
Page 12
3. Move the choke lever to the closed position. Closed position Open position 4. Set the ignition switch to the “start” position. While pulling the throttle lever, push the throttle set button, and release the throttle, then the throttle lever is into the “Start position. Stop position Start position 5.
IMPORTANT • Avoid pulling the rope to its end or returning it by releasing the knob. Such actions can cause starter failures. 6. Move the choke lever to the open position. And pull out the starter rope quickly to restart engine. 8.
Page 14
(1) Idle speed adjuster NOTE • Warm up the engine before adjusting the idling speed. ■ TRIMMER HEAD USAGE WARNING 1. Always wear eye protection such as safety goggles. Never lean over the rotating cutting head. Rocks or other debris could be thrown into eyes and face and cause serious personal injury. 2.
Page 15
8. Operation ----------------------------------------------------------------------------------------------------- ADJUSTING THE LINE LENGTH • Your brushcutter is equipped with a semi- auto type nylon line head that allows the operator to advance the line without stopping the engine. When the line becomes short, lightly tap the head on the ground while running the engine at full throttle.
Page 16
• Make sure to use harness and cutting attachment guard. If not, it is very dangerous since you slip or lose your balance. ■ CUTTING METHOD (a) Use the front left side cutting. (b) Guide the blade from your right to left with it tilted slightly to your left. (c) When mowing a wide area, start working from your left end to avoid interference of cut grass.
Page 17
■ REFILLING TRIMMING LINE 1. When the trimmer line is about to run out, you need to reload a new one. For replacement line, use a diameter of 2.4mm (.095in). The spool is capable for a line up to 4m. Avoid using a larger line as it may cut down the trimming performance.
Page 18
9. Maintenance ----------------------------------------------------------------------------------------------------- 5. Wind up the line in the correct direction as indicated on the spool. 6. Leave the trimmer line around 160mm. Assembly is finished. ■ AIR FILTER • The air filter, if clogged, will reduce the engine performance. Monthly check and clean the filter element in warm, soapy water as required.
■ SPARK PLUG • Starting failure and misfiring are often caused by a fouled spark plug. Clean the spark plug and check that the plug gap is in the correct range. For a replacement plug, use the correct type • Periodically clean the spark plug and check that the spark gap is in the correct range.
Page 20
12. Troubleshooting guide ----------------------------------------------------------------------------------------------------- Starting failure ----------------------------------------------------------------------------------------------------------------------------------------- CHECK PROBABLE CAUSES ACTION ----------------------------------------------------------------------------------------------------------------------------------------- ➞ ➞ drain it and with correct fuel Fuel tank incorrect fuel ➞ ➞ clean Fuel filter fuel filter is clogged Carburetor adjustment screw ➞ ➞ adjust to normal range out of normal range ➞...
Need help?
Do you have a question about the XT-BC508-1 and is the answer not in the manual?
Questions and answers