Advertisement
Quick Links
Please Note!
The Opitec Range of projects is not intended as play toys for
young children. They are teaching aids for young people
learning the skills of craft, design and technology. These pro-
jects should only be undertaken and operated with the
guidance of a fully qualified adult. The finished projects are
not suitable to give to children under 3 years old. Some
parts can be swallowed. Danger of suffocation!
Contents List:
Plywood
Wooden Strip
Wooden Wheel
Wooden Wheel
Wooden Ball with Hole
Coloured Card,
LED, yellow
Small Slide Switch
Resistance 10 Ohm
Welding Wire
Battery Holder, 2x Mignon AA
Jumper Wire, black
Jumper Wire, red
Washer
PVC Hose, transparent
1
117.330
LED-Tree
Tools Needed
Wood Glue
Drill
Side-
All Purpose
Cutter
Glue
Qty:
Size (mm):
1
70x70x6
2
200x30x5
3
ø30x8
4
ø20x6
1
ø15
3
DIN A4
18
ø5
1
19x6
1
1
200x4
1
1
1000
1
2000
3
1
100
Ruler
Scissors
ø2
ø5
Sandpaper
Jigsaw
Engineer´s File
Soldering Iron
Designation:
Base Frame
Side Parts Frame
Spacer Pieces
Spacer Pieces
Top of the Tree
Tree Elements
Lighting
On/Off Switch
Resistance
Tree Trunk
Battery
Cabling
Cabling
Contact
Spacer Pieces
Pencil
Hot Glue Gun
Adhesive Tape
Part No.:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Advertisement
Summary of Contents for Opitec 117.330
- Page 1 Hot Glue Gun Jigsaw Please Note! The Opitec Range of projects is not intended as play toys for young children. They are teaching aids for young people learning the skills of craft, design and technology. These pro- jects should only be undertaken and operated with the guidance of a fully qualified adult.
- Page 2 Instructions 117330 LED-Tree ø2 ø4 Cut the template (page 9) and glue the template with adhesive tape on the base (1). Measure and mark 70mm as well as 80 mm on both wooden strips (2). Cut the wooden strips and clean the saw cuts. Part 2 Part 1 Part 6...
- Page 3 Instructions 117330 LED-Tree Part 1 Part 2 Part 3 Part 4 Part 6 Part 5 Place a ruler to all solid lines and fold them. After that turn the star and fold all Fold all parts 1-6 as described in step 7. dashed lines as well.
-
Page 4: Bottom View
Instructions 117330 LED-Tree Cut off the red welding wire (13) a approx. 100 mm long piece. Strip isolation on both sides and tin them. Solder one end on the resistor (9) and thread the other end upwards through the ø 2mm hole. Solder the free leg of the resistor on the external switch connection and the red cable of the battery holder (11) on the middle switch connector. - Page 5 Instructions 117330 LED-Tree Thread the connection cable, that is coming from part 1, upwards through the hole in tree part 2. Attach tree part 2 as shown and put it on the wooden wheel (3). Anode Cathode long leg bend both legs by 90° short leg Cut off the red an black welding wire (12 + 13) 5 pieces, each with a length of 50 mm.
- Page 6 Instructions 117330 LED-Tree Thread the connection cable, that is coming from part 3, upwards through the hole in tree part 4. Attach tree part 4 as shown and put it on the wooden wheel (3). Anode Cathode long leg bend both legs by 90° short leg Cut off the red an black welding wire (12 + 13) 5 pieces, each with a length of 30 mm.
-
Page 7: Circuit Diagram
Instructions 117330 LED-Tree Put tree part 6 on the welding wire. Attach the wooden ball (5) to the welding wire. Test functioning. Done! Circuit Diagram Tree Part 3 Tree Part 1 Tree Part 5 10 Ohm Battery Switch... - Page 9 Instructions 117330 LED-Tree Template Template Base Base Frame Side Parts M 1:1 M 1:1...
- Page 11 Template Tree Part 1 + Tree Part 6 M 1:1 Part 1 Part 6...
- Page 13 Template Tree Part 2 + Tree Part 5 M 1:1 Part 2 Part 5...
- Page 15 Template Tree Part 3 + Tree Part 4 M 1:1 Part 3 Part 4...