Orcomm DIGITEX Manual

Table of Contents

Quick Links

Download this manual

Contents

Introduction ......................................................................................................................................................... 2

Versions ............................................................................................................................................................... 2

Dimmer ............................................................................................................................................................ 2

Switch .............................................................................................................................................................. 3

STAGE 1 : NET allocation and Setup (Using smart screen) .................................................................................. 3

STAGE 2 : Button function setup ......................................................................................................................... 6

Setting up 2-Way switching: ............................................................................................................................ 6

Smart Screen Contorl .......................................................................................................................................... 7

Room Setup ..................................................................................................................................................... 7

Adding Light Circuits ...................................................................................................................................... 10

Assigning Light Circuits .................................................................................................................................. 11

Creating Scenes on Smart Screen .................................................................................................................. 13

DIGI3 Programming ........................................................................................................................................... 16

Trailing or Leading ......................................................................................................................................... 16

Min and Max .................................................................................................................................................. 16

2-way and intermediate ................................................................................................................................ 17

Kill All ............................................................................................................................................................. 17

Multimaster (including Boost function) ........................................................................................................ 17

Orcomm

Digitex Setup

V2.0

Table of Contents

Summary of Contents for Orcomm DIGITEX

Page 1: Table Of Contents
Orcomm Digitex Setup V2.0 Contents Introduction ................................. 2 Versions ................................2 Dimmer ................................2 Switch ................................3 STAGE 1 : NET allocation and Setup (Using smart screen) .................. 3 STAGE 2 : Button function setup ......................... 6 Setting up 2-Way switching: ..........................6 Smart Screen Contorl ............................
Page 2: Introduction
Introduction This guide is designed to aid in the installation of your Digitex V3 unit, including setting up the NET and pairing of master/slave with the use of a gateway or screen. The Digitex V3 units are designed to be paired together in there own private secure NET.
Page 3: Switch
STAGE 1 : NET allocation and Setup (Using smart screen) Smart Screen Digitex 1. Power the smart screen using a 12v DC PSU or POE network connection. 2. Power on all Digitex light switches. 3. Press the “Lighting Control” button on the home screen.
Page 4 4. Press and hold the bottom right corner of the screen (Hidden button)
Page 5 5. Select “Zigbee Setup” “Zigbee Mode” should be highlighted on the top of the screen.
Page 6: Stage 2 : Button Function Setup
“RST”. Continue to hold the “SET” button for a further 3 seconds. (Main LED will flash) 7. Within 20 seconds you will see the Digitex LED flash 5 times to indicate the NET ID has been accepted and stored. 8. Repeat Steps 6 and 7 for every Digitex unit you wish to pair.
Page 7: Smart Screen Contorl
This is due to the sync messages between the units. Smart Screen Contorl The Orcomm smart screen can be setup to control your Digitex smart switches with a very simple installation process. We first have to add the Rooms to the screen, we then add lighting circuits to the rooms. Finally we can...
Page 8 2. Press and hold the top right hand corner of the screen (Hidden button) to bring up the hidden advanced menu.
Page 9 3. This shows the current rooms that are setup on the smart screen. You can chose to edit these or add new rooms using the “ADD” button. 4. Enter the new room name and select if the room is the default room for the smart screen. (If selected as default room the lighting control page will always show that room first)
Page 10: Adding Light Circuits
Adding Light Circuits Now that we have the rooms setup on the smart screen we can now add the lighting circuits to each room. Select the “Lights” option on the left of the screen. This will show all the lights that are configured for the selected room.
Page 11: Assigning Light Circuits
Now that we have the Rooms, lighting circuits and Digitex units setup we can start assigning the on screen buttons to the physical Digitex unit that the circuit is terminated on. To do this we are going to have to have access to the screen and the smart screen at the same time.
Page 12 Select the room from the list on the left hand side of the room you want to start assigning. Select the main button for the lighting circuit that you want to program. After 5 seconds press the corresponding button on the physical Digitex unit.
Page 13: Creating Scenes On Smart Screen
Repeat steps 4 – 6 for each lighting circuit you want to assign. Please leave 5 seconds between each keypress on the smart screen and the Digitex units. Once completed press the “Zigbee Exit” button The smart screen will take 30sec to finish the setup.
Page 14 A list of scenes will be shown in a list. Click on the “ADD” button to add a new scene. Enter the new scene name and the icon type. Click the new scene that you created from the list.
Page 15 We can now add the circuits to the scene from different rooms. Select the room from the drop down list on the top lift. Click into the box for the circuit that you want to add to the scene. Select the action for the circuit. (Switching and Dimmable circuit will have different options) Repeat the above steps for each lighting circuit that you wish to add to the scene.
Page 16: Digi3 Programming
DIGI3 Programming Channel 2 - UP Channel 1 - UP Channel 2 - Centre Channel 1 - Centre Channel 2 - Down Channel 1 - Down Trailing or Leading To change between Leading to Trailing type of dimming 1. Press and hold SET button for 5 seconds (the buttons will flash) 2.
Page 17: 2-Way And Intermediate
Kill All This function allows the DIGI3 switch to turn OFF all the light switches within the home. Please contact Orcomm support for programmer – currently available through gold partners Multimaster (including Boost function) This allows the DIGI3 to communicate with more than one Master switch. Can also be programmed to give local output for example to activate central MVHR when bathroom light is turned on.

This manual is also suitable for:

Digi2 Digi3Digi3 bled