Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Epson Manuals
  4. Printer
  5. EPL-N2750
  6. Quick reference manual

Epson EPL-N2750 Quick Reference Manual

Epson epl-n2750: reference guide
Hide thumbs Also See for EPL-N2750:

Advertisement

Quick Links

Download this manual See also: Service Manual, Reference Manual

Advertisement

loading

Related Manuals for Epson EPL-N2750

Summary of Contents for Epson EPL-N2750

  • Page 2 As a convenient place to keep this guide, attach the included storage box to the side of your printer as shown below. If the 10-Bin Multi-Purpose Unit is installed, attach the guide storage box to the back of the printer as shown below.

  • Page 3: Preventing Paper Feed And Paper Jam Problems

    Never let more than 500 sheets accumulate in the output tray on top of the printer. Try turning over the stack of paper in the tray. Most paper packages indicate the top side of the paper with an arrow at the side of the package.
  • Page 4 Note: Check for jams at all paper sources or paths indicated on the LCD panel. The printer cannot resume printing until all the jams are cleared. The LCD panel displays up to four paper sources or paths at the same time. Other areas where jams may be occurring will be shown on the LCD panel after you have checked all indicated jams.
  • Page 5 Pull out the cassette indicated on the LCD panel. Carefully remove any paper you find jammed inside the cassette or printer. Remove the stack of paper from the cassette. Even its edges by tapping the paper on a flat surface. Then...
  • Page 6 This message indicates that there may be a paper jam inside cover A or cover B on the right side of the printer. Follow these steps to clear paper jammed inside cover A or B: Open cover A gently. Note:...
  • Page 7 Remove any paper you find jammed inside the printer. If you do not see any paper inside cover A, open cover B. Remove the paper inside cover B. If the paper is difficult to remove, use the gear lever inside cover B as shown below.
  • Page 8 Note: Because the toner on the paper inside the printer may not have been fixed on the page, toner may come off on your hands when you remove the paper. If you spill toner on your clothing, rinse it off with cold water.
  • Page 9 Duplex Unit: Open cover D. Note: Because the toner on the paper inside the printer may not have been fixed on the page, toner may come off on your hands when you remove the paper. If you spill toner on your clothing, rinse it off with cold water.
  • Page 10 5-Bin Multi-Purpose Unit: Open cover E. Note: Because the toner on the paper inside the printer may not have been fixed on the page, toner may come off on your hands when you remove the paper. If you spill toner on your clothing, rinse it off with cold water.
  • Page 11 Bin Multi-Purpose Unit’s paper guide: Open cover F. Note: Because the toner on the paper inside the printer may not have been fixed on the page, toner may come off on your hands when you remove the paper. If you spill toner on your clothing, rinse it off with cold water.
  • Page 12 10-Bin Multi-Purpose Unit. Follow these steps to clear paper jammed at the back of the 10-Bin Multi-Purpose Unit: Move the 10-Bin Multi-Purpose Unit away from the printer. Open cover G on the back of the 10-Bin Multi- Purpose Unit.
  • Page 13 Note: Because the toner on the paper inside the printer may not have been fixed on the page, toner may come off on your hands when you remove the paper. If you spill toner on your clothing, rinse it off with cold water. Using hot water may leave a permanent stain.

  • Page 14: Status And Error Messages

    This section contains an alphabetical list of status, error, and warning messages that appear on the LCD panel. In your printer driver, select the Duplex Print Unit check box in the Optional Settings dialog box, then select the Duplex check box in the Layout tab. Press the Continue button on the control panel to clear the message.
  • Page 15 The Paper Type setting in the printer driver’s Basic Settings tab, or in SelecType, is different from the type of paper loaded in the printer. Make sure the correct type of paper is loaded in the printer; then press the Continue button to clear the message.
  • Page 16 Cover A, on the right side of the MP tray, is open. Pull up the latch on cover A, then close the cover firmly. Warning: Do not touch the hot areas indicated on the caution labels inside cover A. If you still cannot close the cover, the imaging cartridge may not be installed correctly.
  • Page 17 Cover G, on the back of the 10-Bin Multi-Purpose Unit, is open. Move the 10-Bin Multi-Purpose Unit away from the printer, then pull the latch on cover G and close the cover firmly. There is not enough memory for duplex printing. The printer prints only on the top side and ejects the paper.
  • Page 18 To correct this error, (1) press the Continue button, or (2) turn off the printer, then remove the ROM module from slot A. A ROM module which is not formatted is installed in slot B.
  • Page 19 An interface card not supported by this printer is installed. Turn off the printer, then remove the card. A hard disk drive that cannot be used with this printer is installed. Turn off the printer and remove the drive. An option not supported by this printer is installed, or a supported option is installed incorrectly.
  • Page 20 A PostScript 3 ROM module not supported by this printer is installed, or a supported module is installed incorrectly. Make sure you are using the correct PostScript 3 ROM module. If you are, try reinstalling the module. The ROM module in slot A is not supported by this printer, or a supported module is installed incorrectly.
  • Page 21 ALT and Reset buttons at the same time. You can also clear this error by turning the printer off and back on again. However, it may be necessary to reduce the number or size of fonts, reduce the number or size of graphics, lower the resolution, or add more memory to the printer.
  • Page 22 SelecType, which is usually accessible from the printer’s control panel, has been disabled. This setting can be cleared by using the EPSON WebAssist utility. Clear the Panel Lock setting in the Configuration-Printer-Print- Setup Menu. The bin indicated by <N> (1 to 10) on an optional multibin unit is full.
  • Page 23 Press the Continue button to clear this message. Select Face-down Tray (Bin 1) as the Output Tray setting in the printer driver. If you want to output to another tray instead of Bin 1, change the Paper Size setting of your document.
  • Page 24 The printer’s current interface has been reset and the buffer is cleared. However, other interfaces are still active and retain their settings and data. All printer settings have been reset to the user default configuration, or to the last settings that were saved.
  • Page 25 1) exit SelecType by pressing Continue or On Line (the new setting is activated after the current print job is finished), or 2) reset the printer by pressing the ALT and Reset buttons at the same time. The printer is checking the ROM.
  • Page 26 The printer is in its low power state; however, it is still online if the On Line light is on. The printer is almost out of toner. Prepare a new imaging cartridge to replace the current one. You must replace the imaging cartridge. See “Replacing the Imaging Cartridge”...
  • Page 27 ROM was not completed. To correct this error, do one of the following: 1) turn off the printer, then turn it on again, 2) press the Continue button, or 3) reset the printer by pressing the ALT and Reset buttons at the same time.

  • Page 28: Replacing The Imaging Cartridge

    The S051068 cartridge is specially designed for your high-quality 600-dpi printer. Follow these steps to replace the imaging cartridge: Make sure the printer is turned on. Open the printer cover A. function to find out...
  • Page 29 Warning: When opening the printer, do not touch the hot areas indicated by the caution labels inside cover CAUTION Hot Surface Avoid Contact Remove the imaging cartridge by pulling the handles on the front of the cartridge toward you. Dispose of the used imaging cartridge as a nonburnable item.
  • Page 30 While holding the new imaging cartridge horizontally, gently shake it a few times to distribute the toner evenly. Caution: Do not turn the imaging cartridge upside down. Do not expose the imaging cartridge to room light any longer than necessary. Overexposing the cartridge may cause abnormally dark or light areas to appear on the printed page and reduce the life of the...
  • Page 31 When you remove the tape, the handle may spring up quickly enough to hurt your fingers. To avoid this, hold the handle firmly while peeling off the tape. Pick up the imaging cartridge by the carrying handles and insert the cartridge all the way into the printer.
  • Page 32 Close cover A by pushing it up and into the printer. Caution: Never transport the printer with the imaging cartridge installed.