Safety SAFETY-ALERT Watch for this symbol. It Identifies potential hazards to health SYMBOL or personal safety. It means: ATTENTION—BE ALERT Your Safety is Involved Familiarize yourself with the location of all decals. Read them carefully to understand the safe operation of your machine. Three words are used in conjunction with the safety–...
Page 5
Safety Transporting Operation When transporting be aware of length, height, and width. Make turns carefully and be aware of obstacles and overhead electrical lines. When transporting machine adhere to recommended safe speed. DO NOT EXCEED 20 MPH. Do not transport in poor visibility. ...
Page 6
Safety Familiarize yourself with the location of all decals. Read them carefully to understand the safe operation of your machine. If any decals become damaged or missing, contact your dealer immediately for a replacement. December 2019...
Exclusions and/or Deviations from the Base Warranty K-Hart does not cover any warranty on the frame tires. Any warranty has to be dealt with by the Original Tire Manufacturer. K-Hart does not cover any nicks, cuts, or other marks on the frame tires that occur during delivery.
Operation Hitching Insure your hitch pin is in good condition. Position air drill clevis with tractor drawbar using hitch jack. After tractor to air drill connection is made, relieve pressure off the hitch jack. Pull jack pin. Swing hitch jack parallel to hitch pole and re-pin jack. ...
Page 10
Operation Operation Make sure that the wheel bolts on the main center frame and the wings are tightened after the first 5 km and then after the next 10 km and the next 20 km during the first few hours of use or transporting. After the initial use, check wheel bolts every 40 hours of operation.
Page 11
Operation Height Adjustment The height of the frame is controlled by a series of donuts located on the lift cylinders on the center frame. IMPORTANT: Simply add or remove the donuts to set the height, making sure both cylinders are set the same.
Page 12
Operation Setting Openers By adjusting the main tension spring, you will increase the penetrating force of the opener. Moving the bottom of the disc pressure spring towards the rear increases down pressure. Moving the bottom of the disc pressure spring forward towards the tractor decreases down pressure.
Maintenance Use safety lock pins when doing any maintenance on the machine! Frame Daily or every 10 hours Grease rear rockshaft. Weekly or every 50 hours Check for and tighten loose wheel bolts. Check tire pressure. Tires should be maintained at a pressure of 105 psi. ...
Assembly and Parts General Assembly procedure is shown in the following pages. Assembly and parts are shown for all coulter systems and options. Your system may not have all the illustrated parts. Tighten all bolts to the torques shown in the following table unless otherwise instructed.
Page 15
This page intentionally left blank December 2019...
Assembly and Parts 278310: Spring Assembly December 2019...
Page 27
Assembly and Parts 278310: Spring Assembly Item Part No Description 312098 BUSHING, SHOULDER, 3/4 ID 278280 SPRING BASE ASSM 277270 SPRING CENTRE 276230 SPRING HEAD 276170 SPRING, PRESSURE 273322 STOP WASHER 273312 LOWER SPRING PVT SLEEVE 225111 SNAP RING HO-137 TB0812C8P BOLT, 1/2 UNC X 3 GR8 SB0810C5P...
Assembly and Parts 278280: Spring Base Assembly December 2019...
Page 29
Assembly and Parts 278280: Spring Base Assembly Item Part No Description 276265 CAP, VINYL, 7/8 X 1/2 276255 SPRING, COMP, 0.504 X 1.78 X 17 LB/IN 276250 PULL HANDLE 276240 SPRING LOWER PIVOT 276220 BUSHING, SHOULDER, 1 ID X 1 1/4 OD SCS0616C SCREW, SOCKET HEAD CAP, 3/8 UNC X 4 SN06CCP...
Assembly and Parts 678250: Gent Opener Assembly, Right December 2019...
Page 31
Assembly and Parts 678250: Gent Opener Assembly, Right Item Part No Description 677260 GENT OPENER WELDMENT, RH 673503 MUDSCRAPER, RH 626050 BUSHING 1.5 ID X 1 7/8, BLACK 268025 14.8” DISC ASSEMBLY 268020 17” DISC ASSEMBLY 150712 SPINDLE, LEFT 150710 SPINDLE, RIGHT 150701 SPINDLE WASHER...
Assembly and Parts 678255: Gent Opener Assembly, Left December 2019...
Page 33
Assembly and Parts 678255: Gent Opener Assembly, Left Item Part No Description 677263 GENT OPENER WELDMENT, LH 673502 MUDSCRAPER, LH 626050 BUSHING 1.5 ID X 1 7/8, BLACK 268025 14.8” DISC ASSEMBLY 268020 17” DISC ASSEMBLY 150712 SPINDLE, LEFT 150710 SPINDLE, RIGHT 150701 SPINDLE WASHER...
Assembly and Parts 678260: Gent Opener Assembly, Right —RST December 2019...
Page 35
Assembly and Parts 678260: Gent Opener Assembly, Right —RST Item Part No Description 677240 GENT OPENER WELDMENT, RH—RST 673503 MUDSCRAPER, RH 626050 BUSHING 1.5 ID X 1 7/8, BLACK 268025 14.8” DISC ASSEMBLY 268020 17” DISC ASSEMBLY 150712 SPINDLE, LEFT 150710 SPINDLE, RIGHT 150701...
Assembly and Parts 678265: Gent Opener Assembly, Left —RST December 2019...
Page 37
Assembly and Parts 678265: Gent Opener Assembly, Left —RST Item Part No Description 677243 GENT OPENER WELDMENT, LH—RST 673502 MUDSCRAPER, LH 626050 BUSHING 1.5 ID X 1 7/8, BLACK 268025 14.8” DISC ASSEMBLY 268020 17” DISC ASSEMBLY 150712 SPINDLE, LEFT 150710 SPINDLE, RIGHT 150701...
Assembly and Parts 678400: Paralink Linkage Assembly December 2019...
Page 39
Assembly and Parts 678400: Paralink Linkage Assembly Item Part No Description 278310 SPRING ASSEMBLY 277310 MOUNT, LONG 277280 MOUNT, SHORT 277265 PIVOT PIN 277250 UPPER LINK 277200 LOWER LINK 276270 LINKAGE BOLT 276222 BUSHING, 1 ID X 1-1/4 LG, WHITE 276220 BUSHING, SHOULDER, 1 ID X 1 1/4 OD 273310...