Moneual G100 Series User Manual

Hide thumbs

page of 19

/ 19
Bookmarks

Quick Links

Download this manual

Safety Notice:

It is intended for user safety and prevent any accidental damage.

Please read this safety notice carefully before using the product.

DESKTOP COMPUTER

are trademarks, or registered trademarks of MONEUAL Inc. in the Republic of Korea and/or other counties.

USER GUIDE

Applicable Models: G100 Series PC Case

Version: 1.0

Need help?

Do you have a question about the G100 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Moneual G100 Series

Page 1 USER GUIDE Version: 1.0 Applicable Models: G100 Series PC Case Copyright ⓒ 2010 MONEUAL Inc. All rights reserved. The MONEUAL, MONCASO, MiNEW, RYDIS, SONAMU are trademarks, or registered trademarks of MONEUAL Inc. in the Republic of Korea and/or other counties.
Page 3 Before reading this User Guide Before reading this User Guide, please note the following warning icons used in this Guide Warning Icons Forbidden: The product could be damaged. Make sure to observe the instruction. Warning: The operator could be injured. Make sure to observe the instruction.
Page 4 Product Specification The product specification may disagree depending on the product model. For further details, see the label attached to the mainframe of the product or the vendor’ s catalog. Dimension 136(W) x 358(H) x 428(D)mm Compatible Motherboards micro-ATX Compatible Power Supply Units micro-ATX Compatible Graphics Cards Standard ATX...
Page 5 Table of Contents Safety Instructions Components List Front/Rear I/O ports and switches How to assemble your computer G100 DESKTOP COMPUTER USER GUIDE 5...
Page 6 Safety Instructions 1. Carefully read this User Guide before you install the product. 2. Check the parts before you install the product and contact the distributor if there are any missing or defective parts. 3. Before you install the product, wear gloves to prevent probable injuries due to internal parts or peripherals of the case.
Page 7 Components List Part List Parts name / Uded for (English) Figure Q'ty Securing ODD Securing Power supply, HDD, Main-board and Expansion slot Supporting Main-board Covering Expansion slot Isolation between bolt and mainboard Management Cable Securing Fan Mainboard speaker Securing power supply bracket Power supply bracket Case supporter 0 or 4...
Page 8 Front/Rear I/O ports and switches G100 (1) Front view ① ② ⑤ ⑦ ⑥ ③ ⑧ ⑨ G-100 G-100 ④ ①Power saving button ⑥USB port Enter the power saving mode. Connect USB peripherals It is recommended to use the USB ports on the rear ②Optical drive eject button side to connect peripherals (external hard drive, etc.) of power consumption 500 mA or more.
Page 9 Front/Rear I/O ports and switches G100 (2) Rear view ① ② ① Power saving socket ② Main power socket Connect a power strip Connect the power cord of the mainframe. The power saving socket supports up to 1750 W. If the power supported by the power strip is less than 1750 W, connect electronic instruments within the capacity supported by the power strip.
Page 10 How to assemble your computer G100 (1) Remove the side covers and the front panel (bezel) Side cover ① Remove the 4 hand screws on the rear side ② After removing the both side covers, widen and then remove the two side covers. the hook on both sides of the bezel to remove the bezel.
Page 11 How to assemble your computer G100 (3) Graphic card installation ① Check the graphic card slot on the motherboard. (The slot specification is common to all vendors but the shape of slot may look a little different from vendor to vendor.) ②...
Page 12 How to assemble your computer G100 (4) HDD, ODD Installation ① As shown in the figure, mount the CD/DVD drive and the hard disk on the drive bay rack and tighten the setscrews. (Back Side) ② Install the drive bay rack with ODD and HDD installed and tighten the setscrews. Tighten the setscrews.
Page 13 How to assemble your computer G100 ③ As shown in the figure, connect the power connector and data connector of the CD/DVD driver and the hard disk. Connect the hard disk connector (HDD) Connect the CD/DVD drive connector (ODD) G100 DESKTOP COMPUTER USER GUIDE 13...
Page 14 How to assemble your computer G100 (5) Cable connection The motherboard and the power supply unit may be damaged if the pin and connector cables are not exactly aligned. Connect the cable after checking the wiring, referring to the manuals of the motherboard and the power supply unit.
Page 15 How to assemble your computer G100 3) Front USB Connection Connect the power connectors of the power saving module and the main power supply unit. Since the connector port is shaped in a polygon as shown in the figure, it would not be connected in a wrong direction.
Page 16 How to assemble your computer G100 6) Front Audio Connection As shown in the figure, the audio connector would not be connected if the F_AUDIO pins are not exactly aligned to the connector port. Exactly install the connector by checking the pin array and the key (no pin) position. PRESENCE# MIC_JD LINE out_R...
Page 17 How to assemble your computer G100 (6) Cable Connection Assemble the cables in the sequence order of the front panel removal in Page 10 (See P10). ① Mount the bezel while checking the position of hook. ② Mount the two side covers and tighten the four hand screws. G100 DESKTOP COMPUTER USER GUIDE 17...
Page 18 18 G100 DESKTOP COMPUTER USER GUIDE...
Page 19 Service hours Weekdays: 09:00 ~ 18:00, Weekend: 09:00 ~ 12:00 Copyright ⓒ 2010 Moneual Inc. All rights reserved. The MONEUAL, MONCASO, MiNEW, RYDIS, SONAMU are trademarks, or registered trademarks of Moneual Inc. in the Republic of Korea and/or other countries.