1. Manuals
  2. Brands
  3. Wavion Manuals
  4. Network Hardware
  5. WCPEn-2400-I
  6. Quick start manual

Wavion WCPEn-2400-I Quick Start Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

WCPEn-2400-I Quick Start Guide
February 2012
Version 1.0

Advertisement

Table of Contents
loading

Related Manuals for Wavion WCPEn-2400-I

Summary of Contents for Wavion WCPEn-2400-I

  • Page 1 WCPEn-2400-I Quick Start Guide February 2012 Version 1.0...

  • Page 2: Table Of Contents

    ....................... - 5 - RODUCT AYOUT 2.3 I ....................- 6 - NSTALLATION AND 2.3.1 Installing the WCPEn-2400-I ..................- 6 - 2.4 C ..................... - 7 - ONNECTING OWER AND 2.4.1 Accessing the WCPEn Management Interface .............. - 7 - CONFIGURING WCPEN ....................
  • Page 3 This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Note: Wavion and its resellers or distributors are not liable for injury, damage or regulation violations associated with the installation of outdoor units or antennas.

  • Page 4: Introduction

    1. Introduction This document describes how to set-up, configure and use the WCPEn-2400-I unit. The WCPEn-2400-I is a 2x2 MIMO IEEE 802.11b/g/n wireless indoor CPE, which supports high throughput up to 300Mbps, as well as supporting the unique dual-zone functionality that enables it to connect as a long-range wireless through the WAN to the outdoor WBSn base station, and repeat the signal to the LAN.

  • Page 5: Installation

     2.2 Product Layout The image above represents the WCPEn-2400-I. The LAN and DC ports are located on the side of the unit, and LEDs that indicate the Power, LAN and the signal strength are located on the front. WCPEn 1.0 User Guide...

  • Page 6: Nstallation And Et Up

    2. Connect both antennas to the WCPE-2400-I unit. 3. Connect WCPEn-2400-I to a power source, using the power supply unit. The power LED switches on. 4. Connect WCPEn-2400-I to your PC, using a network cable. The LAN LED switches on.

  • Page 7: Connecting Power And Data

    2.4 Connecting Power and Data In order to manage the WCPEn-2400-I, your PC and the WCPEn-2400-I management IP should be on the same sub-network. The WCPEn-2400-I management IP is: 192.168.1.2 The following procedure describes how to modify your PC IP address, for Windows XP operating systems.

  • Page 8: Configuring Wcpen

    3.1 General Configuration Most of the default settings in the WCPEn-2400-I are pre-defined in order that you do not have to reset them, or make any changes. However, certain elements require personalization, as described below.
  • Page 9 The Client Router operation mode means that both the Network Address Translation (NAT) and the IP address for the PC connected to the WCPEn-2400-I LAN port are provided by the DHCP server at the gateway router, rather than by the unit.
  • Page 10 Note: If indicated in the list of access points that security settings need to be configured, click Security Settings: a. Enter the SSID string of your home system. b. Specify the security mode according to your system requirements. For more information, see Security, Authentication and Encryption Modes table.
  • Page 11 4. You must define two Virtual AP (VAPs) for Dual Zone Bridge Operation Mode. VAP1 is the VAP which connects to the outdoor base station, and VAP 2 is the VAP signal to WCPEn-2400-I. 5. To specify the first VAP, navigate to Configuration => Wireless => Wireless Setting.
  • Page 12 4. You must define two VAPs for Dual Zone Router operation mode. VAP1 is the VAP which connects to the outdoor base station, and VAP 2 is the VAP signal to WCPEn-2400-I. 5. To specify the first VAP, navigate to Configuration => Wireless => Wireless Setting.
  • Page 13 Note: If indicated in the list of access points that security settings need to be configured, click Security Settings: a. Enter the SSID string of your home system. b. Specify the security mode according to your system requirements. For more information, see Security, Authentication and Encryption Modes table.

  • Page 14: Specifying Wireless Settings

    3.1.3 Specifying Wireless settings To specify Wireless Settings 1. Navigate to Configuration => Wireless => Wireless Settings. 2. In Site Survey, click Scanning to locate and display a list of the available local WBSn base stations. 3. Click Connect on the Base Station to which you wish to connect, and click Close. WCPEn 1.0 User Guide Page - 14 -...

  • Page 15: Security Settings

    The firmware upgrade capability enables you to upgrade your system firmware, or to rollback to a previously saved version. 1. In the WCPEn-2400-I management interface, navigate to Administration => Firmware Upgrade. 2. Browse to the location in which the upgrade file is located.

  • Page 16: Status

    3. A window is displayed, asking you if you wish to save or open your backup file. 4. Select Save File, and click OK. 5. To restore a system configuration setup from a previously saved backup file, click Browse in the Restore File field, and navigate to the location where the this file was saved.

  • Page 17: Ip Management

    3.4.2 IP Management To Configure a Management IP address 1. Navigate to Configuration => Network => LAN Setting. 2. Modify the IP address and NetMask values according to your local network specification, as required. Parameter Description IP Address Change the management IP address Mask Enter the required network mask DHCP Server Setting...

  • Page 18: Appendix B: Troubleshooting

    4. Appendix B: Troubleshooting We hope your experience with the WCPEn-2400-I is as smooth as possible. In this section we provide tips to solve some common problems. 4.1 Basic Troubleshooting Problem Solution Default user and password User: admin Password: admin Unable to Ping or HTTP the new unit ...

Table of Contents