cliMATE HP32 Handbook

HP32
SL 3.0
Proportional feedback
Handbook
MAIN SETTINGS (Run Mode)
SETTING
Press SET:
This message will be displayed instead of the
°Set temperature value.
Press + or - to modify, press SET to confirm.
At this point: this message will be displayed instead of the
Position minimum opening % value.
Press + or - to modify, press SET to confirm.
At this point: this message will be displayed instead of the
Position maximum opening % value.
Press + or - to modify, press SET to confirm.
POSITION VIEWING
Press SET for at least one second (and not for more 5
seconds, because an Init procedure is then issued):
this message will be displayed showing the current % position.
VIEWING TEMPERATURE RECORDING
Press + : will be displayed followed by
& hold
°Maximum Temperature Recording.
Press - : will be displayed followed by
& hold
°Minimum Temperature Recording.
Values recorded are permanently stored in the memory. To clear memory push + key
for more than 3 seconds: CLEA message will be displayed before clearing operation.
FLAP POTENTIOMETER INITILIZATION PROCEDURE (Init)
Connect the potentiometer of any value (max 10Kohm, recommended 1 Kohm)
must be applied to the flap motor.
Having done this, proceed as follows to record the potentiometer values.
Press SET key for at least 5 seconds: when Init message is displayed for more
than one second. Release SET key. HP32 closes the flap (light CLOSE flashes)
and the potentiometer resistance value is displayed.
When the flap has completely closed, press SET to record the value: at this point HP32
opens the flap (light OPEN flashes) and the potentiometer resistance value is displayed.
When the flap has completely opened, press SET to record the value.
HP32 then returns automatically to the Run mode.
COSt PROGRAMMING (System constants)
These settings refer to the mode operation of the system and must be made on
initial start-up.
Press - / + together for at least one second: the message C.O.S.t. will be
Example con t.SEt = 25.0°C
displayed.
Press SET repeatedly until the desired variable's message is displayed (see table
below) : variable value and related message will be displayed.
Press + or - to set a new value and then SET to confirm.
The next system constant will then appear.
Example con Po._ _ = 0%
You can press SET for a least two seconds to escape and return to the Run Mode.
M e s . s V a
P o r P . 4
Example con Po.-- = 100%
P t c 1 . 0
P c n 1 . 5
0
P o C . L
9 9
P o O . P
=
E t n P
Example with percentual= 53%
. 0
A . d E t
*1) For more details see Operating Diagram.
*2) Flap position when zone temperature equals SET temperature (SET key in Run Mode)
(0 is fully closed).
*3) If hunting occurs when searching for the position during flap operation (due to
mechanical gearmotor hysteresis), increase the Pcn.1 setting value until it is
eliminated.
*4) Values can be entered in hand mode or are automatically set by Init procedure.
*5) tEnP =0 : °C Temperature range.
tEnP =1 : °F Temperature range.
*6) You can correct the readings on the sensor (+ or -).
u l e M e a n
° 0 ° C P o r p o t r o i n l a a r n g e
% P o t i s o i n a l f p o t S E T
% N e u r t l a a r n g e
P o e t t n o i m t e r e e r s s i a t c n e n i a l f p
9 9
P o e t t n o i m t e r e e r s s i a t c n e n i a l f p
1
e T m p e a r u t e r e r p e r s e t n t a o i n
° 0
° C s e s n r o e t m p e a r u t e r c r o e r t c o i
n i g N o e t
1 *
2 *
3 *
4 *
c o l s e d p o t i s o i n
4 *
o p e n p o t i s o i n
5 *
6 *
n + ( r o ) -