GMI INTELLICODE 1 Quick Start Manual

WIRELESS KEYPAD INTELLICODE® 1 MODE
To Operate Intellicode® 1 Openers:
This Wireless Keypad comes from the factory as an Intellicode® 2 unit.
In order to initially program an opener or openers which are
Intellicode®1, you must switch the Keypad to Intellicode®1 mode.
• After entering your PIN, Press
Press and hold for two seconds and the
•
PROGRAM
GREEN LED above the number keys will turn RED.
• Close the Keypad cover.
Follow the instructions on this page for programming
•
your Intellicode® 1 opener(s).
Once all your doors have been programmed, there is no need to
switch back and forth between Intellicode® modes. The Keypad will
automatically remember the mode of each opener.
SECTION
B P
ASIC ROGRAMMING FOR
1
D INTELLICODE®
O OR
FOR CONVENIENCE
Program Keypad BEFORE mounting.
S 1:
C Y W
TEP
REATING OUR
(P I
ERSONAL DENTIFICATION
• Press in order
3 5
• Press .
PROGRAM
• Enter your PIN (3 to 8 characters).
Press .
•
PROGRAM
• Close keypad cover and wait 30 seconds.
S 2:
T PIN
TEP
EACHING TO
Find the Learn Code Button and Learn Code
Indicator LED on your door opener.
–
If your Door Opener has a black
antenna wire and the serial
number does not start with
10 or higher, the Learn Code
Button and Indicator LED are
located near the antenna. (The
light lens may need to be
opened. If you use an external
receiver, it may need to be opened
to access the Learn Code Button
and Indicator LED.
– If your Door Opener does not
have an Antenna,
you have an External Receiver.
The External Receiver cover
must be removed to access
the Learn Code Button
and Indicator LED.
• Press the Learn Code Button.
– Learn Code Indicator LED (on Opener) will blink.
• Enter your PIN and press
– Learn Code Indicator LED stays on.
• Press again.
– Learn Code Indicator LED turns off.
• Press again.
– Opener will run.
Wait until Keypad Backlight turns off (approximately 30 seconds).
S 3:
O O
TEP
PERATING NE
To open or close the Garage Door.
• Enter your PIN.
• Press .
NOTE
If the Door does not move,check the red LED on
•
Keypad. If the LED is blinking rapidly,the PIN was
entered incorrectly. After the LED stops blinking,re-enter
your PIN and try again.
Any Keypad Button will control the Door for 30 seconds
•
after the Door starts moving.
Rapid blinking of the red LED indicates an error. After a
•
few seconds the LED will turn off. Start over.
Proceed to Section 3 - Mounting Instructions.
For answers to questions, call 1-800-35- GENI E , or visit
www.geniecompany.com
The Genie Company, 22790 Lake Park Blvd., Alliance, Ohio 44601
A dditional Genie® products can be ordered through your local
.
Genie® Professional Dealer. To locate a dealer near you,
call 1-800-OK-GENIE.
©2010 GMI Holdings, Inc. D.B.A.The
SECTION
O
NE
Program Keypad BEFORE mounting.
O
PENER
S
K PIN
IRELESS EYPAD
N )
UMBER
.
7
S
TEP
S O
INGLE PENER
Red Indicator
LED
Located
on Opener
Housing
Learn
Code
Button
on Keypad.
Wait until Keypad Backlight turns off (approximately 30 seconds).
S
D O
OOR PENER
Genie Compan y
P
ROGRAMMING FOR
2
D INTELLICODE®
O OR
FOR CONVENIENCE
1:
C Y W
TEP
REATING OUR IRELESS
(P I N
ERSONAL DENTIFICATION UMBER
• Press in order .
3 5 7
• Press .
PROGRAM
• Enter your PIN (3 to 8 characters).
Press .
•
PROGRAM
• Close keypad cover and wait 30 seconds.
2:
P M
ROGRAMMING ULTIPLE
All Door Openers will use the same PIN.
On your keypad:
• Enter your PIN and press
PROGRAM
• Press
again.
PROGRAM
• Press the number of Doors (total) you wish
to control ( or ).
2 3
• Press .
PROGRAM
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
Decide which Door will be Door #1,#2 and #3.
• Enter your PIN and press
• Press the
number you have picked for this
Door Opener ( or or
1 2
• Press and hold the
for 2 seconds.
PROGRAM
• Press the Learn Code Button. (See Step 2 in Section 1.)
• Press 3 times.
– Opener will run.
Repeat procedure below dotted line for each opener.
(Each Door Opener must be programmed to receive the
signal from the Wireless Keypad).
3:
O M
TEP
PERATING ULTIPLE
To open or close a Door after programming is complete.
• Enter your PIN.
• Press .
• Press Door Opener number (
1
2 3
OR
O
PENER
K PIN
EYPAD
)
D O
OOR PENERS
.
on Keypad.
).
3
D O
OOR PENERS
or or ).
2 3