Page 1 2006 Cadillac SRX Owner Manual Seats and Restraint Systems ... 1-1 Front Seats ... 1-2 Rear Seats ... 1-9 Safety Belts ... 1-11 Child Restraints ... 1-28 Airbag System ... 1-50 Restraint System Check ... 1-62 Features and Controls ... 2-1 Keys ...
Page 2: How To Use This Manual
GENERAL MOTORS, GM, the GM Emblem, CADILLAC, the CADILLAC Crest and Wreath, and the name SRX are registered trademarks of General Motors Corporation. This manual includes the latest information at the time it was printed. We reserve the right to make changes to the product after that time without notice.
Page 3 Index A good place to quickly locate information about the vehicle is the Index in the back of the manual. It is an alphabetical list of what is in the manual and the page number where it can be found. Safety Warnings and Symbols There are a number of safety cautions in this book.
Page 4: Vehicle Symbols
Vehicle Damage Warnings Also, in this manual you will ﬁnd these notices: Notice: These mean there is something that could damage your vehicle. A notice tells about something that can damage the vehicle. Many times, this damage would not be covered by your vehicle’s warranty, and it could be costly.
Page 5 These are some examples of symbols that may be found on the vehicle:...
Page 6 NOTES...
Page 7: Table Of Contents
Section 1 Front Seats ...1-2 Manual Passenger Seat ...1-2 Power Seats ...1-2 Power Lumbar ...1-3 Heated Seats ...1-4 Reclining Seatbacks ...1-5 Head Restraints ...1-7 Rear Seats ...1-9 Rear Seat Operation ...1-9 Stowable Seat ...1-9 Safety Belts ...1-11 Safety Belts: They Are for Everyone ...1-11 Questions and Answers About Safety Belts ...1-15 How to Wear Safety Belts Properly ...1-16 Driver Position ...1-16...
Page 8: Front Seats
Front Seats Manual Passenger Seat Your vehicle may have a manual passenger seat. To adjust the seat, lift the bar under the front of the seat to unlock it. Slide the seat to where you want it and release the bar. Try to move the seat back and forth with your body to be sure the seat is locked in place.
Page 9: Power Lumbar
• Move the front of the horizontal control up or down to raise or lower the front part of the cushion. • Move the rear of the horizontal control up or down to raise or lower the rear part of the cushion. •...
Page 10 Heated Seats If your vehicle is equipped with heated front seats, the buttons are located on the climate control panel. There is one button for the driver and one for the front passenger. Each button has three settings, LO, HI and off.
Page 11: Reclining Seatbacks
Reclining Seatbacks Manual Recline Lever If your front passenger’s seat has a manual reclining seatback, the lever is located on the outboard side of the seat. Lift the lever to release the seatback, then move the seatback to where you want it. Release the lever to lock the seatback in place.
Page 12 Power Recliner If your vehicle has power reclining seatbacks, the control is located on the outboard side of the front seats. Press the top of the vertical control forward or rearward to adjust the seatback angle. Do not have a seatback reclined if your vehicle is moving.
Page 13: Head Restraints
CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts cannot do their job when you are reclined like this. The shoulder belt cannot do its job. In a crash, you could go into it, receiving neck or other injuries.
Page 14 Adjust your head restraint so that the top of the restraint is closest to the top of your head. This position reduces the chance of a neck injury in a crash. The second row outboard head rests can be adjusted up and down.
Page 15: Rear Seats
Rear Seats Rear Seat Operation Adjusting the Second Row Seat The second row seat can be adjusted forward or rearward. Pull up on the lever under the seat cushion and slide the seat with your body. Release the lever and try to move the seat forward and rearward to be sure it is locked into place.
Page 16 Inside Liftgate The buttons that are used to operate the power folding third row seat are located inside of the liftgate and behind the second row seat on the passenger’s side of the vehicle. Two buttons are located inside the liftgate. One button is to tilt the seatback forward for added storage space or when storing a ﬂat tire.
Page 17 Safety Belts Safety Belts: They Are for Everyone This part of the manual tells you how to use safety belts properly. It also tells you some things you should not do with safety belts. CAUTION: Do not let anyone ride where he or she cannot wear a safety belt properly.
Page 18: Why Safety Belts Work
You never know if you will be in a crash. If you do have a crash, you do not know if it will be a bad one. A few crashes are mild, and some crashes can be so serious that even buckled up, a person would not survive.
Page 19 Put someone on it. Get it up to speed. Then stop the vehicle. The rider does not stop. 1-13...
Page 20 The person keeps going until stopped by something. or the instrument panel... In a real vehicle, it could be the windshield... 1-14...
Page 21 or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense. Questions and Answers About Safety Belts Will I be trapped in the vehicle after an accident...
Page 22 If I am a good driver, and I never drive far from home, why should I wear safety belts? You may be an excellent driver, but if you are in an accident — even one that is not your fault — you and your passengers can be hurt.
Page 23 The shoulder belt may lock if you pull the belt across you very quickly. If this happens, let the belt go back slightly to unlock it. Then pull the belt across you more slowly. 4. Push the latch plate into the buckle until it clicks. Pull up on the latch plate to make sure it is secure.
Page 24 What is wrong with this? The shoulder belt is too loose. It will not give nearly as much protection this way. 1-18 CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
Page 25 What is wrong with this? The belt is buckled in the wrong place. CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not at the pelvic bones.
Page 26 What is wrong with this? The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. 1-20 CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Page 27 What is wrong with this? The belt is twisted across the body. CAUTION: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer to ﬁx it.
Page 28 To unlatch the belt, just push the button on the buckle. The belt should go back out of the way. Before you close the door, be sure the belt is out of the way. If you slam the door on it, you can damage both the belt and your vehicle.
Page 29 Right Front Passenger Position To learn how to wear the right front passenger’s safety belt properly, see Driver Position on page 1-16. The right front passenger’s safety belt works the same way as the driver’s safety belt — except for one thing. If the belt stops before it reaches the buckle, tilt the latch plate and keep pulling until you can buckle the belt.
Page 30 Lap-Shoulder Belt All rear seat positions have lap-shoulder belts. Here is how to wear one properly. 1. Pick up the latch plate and pull the belt across you. Do not let it get twisted. The shoulder belt may lock if you pull the belt across you very quickly.
Page 31 The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones. And you would be less likely to slide under the lap belt. If you slid under it, the belt would apply force at your abdomen.
Page 32 Rear Safety Belt Comfort Guides Rear shoulder belt comfort guides provide added safety belt comfort for older children who have outgrown booster seats and for small adults. When attached to a shoulder belt, the comfort guide better positions the belt away from the neck and head. There is one guide available for each of the rear outside passenger positions in the second row.
Page 33 4. Buckle, position and release the safety belt as described in Rear Seat Passengers on page 1-23. Make sure that the shoulder belt crosses the shoulder. CAUTION: A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured.
Page 34: Child Restraints
Safety Belt Pretensioners Your vehicle has safety belt pretensioners for the driver and right front passenger. Although you cannot see them, they are located on the buckle end of the safety belts. They help the safety belts reduce a person’s forward movement in a moderate to severe frontal and near frontal crash.
Page 35: Safety Belts
What is the proper way to wear safety belts? An older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. The shoulder belt should not cross the face or neck. The lap belt should ﬁt snugly below the hips, just touching the top of the thighs.
Page 36 What if a child is wearing a lap-shoulder belt, but the child is so small that the shoulder belt is very close to the child’s face or neck? If the child is sitting in a seat next to a window, move the child toward the center of the vehicle.
Page 37: Infants And Young Children
CAUTION: Never do this. Here a child is sitting in a seat that has a lap-shoulder belt, but the shoulder part is behind the child. If the child wears the belt in this way, in a crash the child might slide under the belt.
Page 38 CAUTION: People should never hold a baby in their arms while riding in a vehicle. A baby does not weigh much — until a crash. During a crash a baby will become so heavy it is not possible to hold it. For example, in a crash at only 25 mph (40 km/h), a 12 lb (5.5 kg) baby will suddenly become a 240 lb (110 kg) force on a person’s arms.
Page 39 CAUTION: Children who are up against, or very close to, any airbag when it inﬂates can be seriously injured or killed. Airbags plus lap-shoulder belts offer protection for adults and older children, but not for young children and infants. Neither the vehicle’s safety belt system nor its airbag system is designed for them.
Page 40 What are the different types of add-on child restraints? Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types. Selection of a particular restraint should take into consideration not only the child’s weight, height and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used.
Page 41: Child Restraints
CAUTION: The body structure of a young child is quite unlike that of an adult or older child, for whom the safety belts are designed. A young child’s hip bones are still so small that the vehicle’s regular safety belt may not remain low on the hip bones, as it should.
Page 42 A rear-facing infant seat (B) provides restraint with the seating surface against the back of the infant. The harness system holds the infant in place and, in a crash, acts to keep the infant positioned in the restraint. 1-36 A forward-facing child seat (C-E) provides restraint for the child’s body with the harness and also sometimes with surfaces such as T-shaped or shelf-like shields.
Page 43 A booster seat (F-G) is a child restraint designed to improve the ﬁt of the vehicle’s safety belt system. Some booster seats have a shoulder belt positioner, and some high-back booster seats have a ﬁve-point harness. A booster seat can also help a child to see out the window.
Page 44: Where To Put The Restraint
When choosing a child restraint, be sure the child restraint is designed to be used in a vehicle. If it is, it will have a label saying that it meets federal motor vehicle safety standards. Then follow the instructions for the restraint. You may ﬁnd these instructions on the restraint itself or in a booklet, or both.
Page 45: Lower Anchors And Tethers For Children (Latch)
Wherever you install a child restraint, be sure to secure the child restraint properly. Keep in mind that an unsecured child restraint can move around in a collision or sudden stop and injure people in the vehicle. Be sure to properly secure any child restraint in your vehicle —...
Page 46: Top Tether Anchor
Lower Anchors Lower anchors (A) are metal bars built into the vehicle. There are two lower anchors for each LATCH seating position that will accommodate a child restraint with lower attachments (B). 1-40 Top Tether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle.
Page 47 Some top tether-equipped child restraints are designed for use with or without the top tether being attached. Others require the top tether always to be attached. In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached.
Page 48 To assist you in locating the top tether anchors, the top tether anchor symbol is located near the top tether anchors. There are two top tether anchors located on the side of the wheel well in the rear cargo area. There is another top tether anchor in the center of the rear cargo area.
Page 49: Securing A Child Restraint Designed For The Latch System
Securing a Child Restraint Designed for the LATCH System CAUTION: If a LATCH-type child restraint is not attached to anchors, the restraint will not be able to protect the child correctly. In a crash, the child could be seriously injured or killed. Make sure that a LATCH-type child restraint is properly installed using the anchors, or use the vehicle’s safety belts to secure the restraint,...
Page 50 5. If the child restraint is forward-facing, attach and tighten the top tether to the top tether anchor. Refer to the child restraint instructions and the following steps: 5.1. Find the top tether anchor. 5.2. If you have an adjustable head restraint, raise the head restraint.
Page 51: Securing A Child Restraint In A
Securing a Child Restraint in a Rear Seat Position If your child restraint is equipped with the LATCH system, see Lower Anchors and Tethers for Children (LATCH) on page 1-39. There are no top tether anchors in the third row seating positions.
Page 52 3. Buckle the belt. Make sure the release button is 4. Pull the rest of the shoulder belt all the way out of positioned so you would be able to unbuckle the the retractor to set the lock. safety belt quickly if you ever had to. 1-46...
Page 53 5. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. If you are using a forward-facing child restraint, you may ﬁnd it helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 54: Securing A Child Restraint In The Right Front Seat Position
Securing a Child Restraint in the Right Front Seat Position If your child restraint is equipped with the LATCH system, see Lower Anchors and Tethers for Children (LATCH) on page 1-39. There is no top tether anchor in the right front passenger’s position.
Page 55 3. Pick up the latch plate, and run the lap and shoulder portions of the vehicle’s safety belt through or around the restraint. The child restraint instructions will show you how. 4. Tilt the latch plate to adjust the belt if needed. 5.
Page 56: Airbag System
6. To tighten the belt, pull up on the shoulder belt while you push down on the child restraint. You may ﬁnd it helpful to use your knee to push down on the child restraint as you tighten the belt. 7.
Page 57 Here are the most important things to know about the airbag system: CAUTION: You can be severely injured or killed in a crash if you are not wearing your safety belt — even if you have airbags. Wearing your safety belt during a crash helps reduce your chance of hitting things inside the vehicle or being ejected from it.
Page 58 CAUTION: Both frontal and side impact airbags inﬂate with great force, faster than the blink of an eye. If you are too close to an inﬂating airbag, as you would be if you were leaning forward, it could seriously injure you. Safety belts help keep you in position for airbag inﬂation before and during a crash.
Page 59: Where Are The Airbags
There is an airbag readiness light on the instrument panel, which shows the airbag symbol. The system checks the airbag electrical system for malfunctions. The light tells you if there is an electrical problem. See Airbag Readiness Light on page 3-37 for more information.
Page 60 The front passenger’s frontal airbag is in the instrument panel on the passenger’s side. 1-54 The driver’s side impact airbag is in the side of the driver’s seatback closest to the door.
Page 61 The right front passenger’s side impact airbag is in the side of the passenger’s seatback closest to the door. The roof-mounted side impact airbag for the driver and the passenger directly behind the driver is in the ceiling above the side windows. 1-55...
Page 62 The roof-mounted side impact airbag for the front passenger and the passenger directly behind the front passenger is in the ceiling above the side windows. 1-56 CAUTION: If something is between an occupant and an airbag, the airbag might not inﬂate properly or it might force the object into that person causing severe injury or even death.
Page 63: When Should An Airbag Inﬂate
When Should an Airbag Inﬂate? The driver’s and right front passenger’s frontal airbags are designed to inﬂate in moderate to severe frontal or near-frontal crashes. But they are designed to inﬂate only if the impact exceeds a predetermined deployment threshold. Deployment thresholds take into account a variety of desired deployment and non-deployment events and are used to predict how severe a crash is likely to be in time for the airbags to inﬂate and help...
Page 64: What Makes An Airbag Inﬂate
Roof-mounted side impact airbags are “rollover capable” and are intended to inﬂate in moderate to severe side crashes or during a rollover. Roof-mounted side impact airbags are not intended to inﬂate in frontal or near-frontal impacts or rear impacts. A side impact airbag will inﬂate if the crash severity is above the system’s designed “threshold level.”...
Page 65: What Will You See After An Airbag Inﬂates
What Will You See After an Airbag Inﬂates? After frontal airbags and seat-mounted side impact airbags inﬂate, they quickly deﬂate, so quickly that some people may not even realize an airbag inﬂated. Roof-mounted side impact airbags deﬂate more slowly and may still be at least partially inﬂated minutes after the vehicle comes to rest.
Page 66 Your vehicle has a feature that will automatically unlock the doors and turn the interior lamps on when the airbags inﬂate (if battery power is available). You can lock the doors again and turn the interior lamps off by using the door lock and interior lamp controls. The hazard warning ﬂashers will also come on when the airbags deploy.
Page 67: Servicing Your Airbag-Equipped Vehicle
Servicing Your Airbag-Equipped Vehicle Airbags affect how your vehicle should be serviced. There are parts of the airbag system in several places around your vehicle. Your dealer and the service manual have information about servicing your vehicle and the airbag system. To purchase a service manual, see Service Publications Ordering Information on page 7-15.
Page 68: Restraint System Check
Restraint System Check Checking the Restraint Systems Now and then, make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired.
Page 69: Replacing Restraint System Parts
Replacing Restraint System Parts After a Crash CAUTION: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible.
Page 70 NOTES 1-64...
Page 71: Features And Controls
Section 2 Keys ...2-3 Remote Keyless Entry System ...2-4 Remote Keyless Entry System Operation ...2-5 Doors and Locks ...2-8 Central Door Unlocking System ...2-9 Power Door Locks ...2-9 Delayed Locking ...2-9 Programmable Automatic Door Locks ...2-10 Rear Door Security Locks ...2-10 Lockout Protection ...2-11 Power Liftgate ...2-12 Windows ...2-14...
Page 72 Section 2 Storage Areas ...2-46 Glove Box ...2-46 Cupholder(s) ...2-46 Cell Phone Storage Area ...2-46 Front Storage Area ...2-46 Center Console Storage Area ...2-46 Luggage Carrier ...2-47 Convenience Net ...2-48 Features and Controls Cargo Cover ...2-48 Cargo Management System ...2-48 Sunroof ...2-48 Sunroof (UltraView) ...2-48 Sunroof (UltraView Plus) ...2-50...
Page 73: Keys
Keys CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons. They could operate the power windows or other controls or even make the vehicle move. The children or others could be badly injured or even killed.
Page 74: Remote Keyless Entry System
Notice: If you ever lock your keys in your vehicle, you may have to damage the vehicle to get in. Be sure you have spare keys. In an emergency, contact Cadillac Roadside Service See Roadside Service on page 7-6. If your vehicle is equipped with the OnStar an active subscription and you lock your keys inside ®...
Page 75: Remote Keyless Entry System Operation
At times you may notice a decrease in range. This is normal for any remote keyless entry system. If the transmitter does not work or if you have to stand closer to your vehicle for the transmitter to work, try this: •...
Page 76: Matching Transmitter(S) To Your Vehicle
If your vehicle is programmed for remote conﬁrmation, the doors must be closed for this feature to work. If a door is open, remote conﬁrmation will be canceled. (Unlock): Press this symbol on the remote keyless entry transmitter to unlock the driver’s door. This also disarms the theft-deterrent system.
Page 77: Battery Replacement
Battery Replacement Under normal use, the battery in your remote keyless entry transmitter should last about four years. You can tell the battery is weak if the transmitter will not work at the normal range in any location. If you have to get close to your vehicle before the transmitter works, it is probably time to change the battery.
Page 78: Doors And Locks
Doors and Locks CAUTION: Unlocked doors can be dangerous. • Passengers — especially children — can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked.
Page 79: Central Door Unlocking System
Central Door Unlocking System Your vehicle has a central door unlocking feature. When unlocking the driver’s door, you can unlock the other doors by holding the key in the turned position for a few seconds or by quickly turning the key twice in the lock cylinder.
Page 80: Programmable Automatic Door Locks
Programmable Automatic Door Locks Your vehicle is programmed so that when the doors are closed, the ignition is on and the shift lever is moved out of PARK (P), all the doors will lock. The front door inside handles will remain active. The doors will unlock every time you stop the vehicle and move the shift lever back into PARK (P).
Page 81: Lockout Protection
When you want to open a rear door when the security lock is on, do the following: 1. Unlock the door using the remote keyless entry transmitter, the front door power lock switch or by lifting the rear door manual lock. 2.
Page 82: Power Liftgate
Power Liftgate Power Liftgate Operation Your vehicle has a power liftgate. The vehicle must be in PARK (P) to power open or close the liftgate. The liftgate must be completely closed to power open or the liftgate completely open to power close. The taillamps will ﬂash and a chime will sound at the beginning of each power operation cycle.
Page 83 Obstacle Detection Features If the liftgate encounters an obstacle during a power open or close cycle, a warning chime will sound and the liftgate will automatically reverse direction to the full closed or open position. After removing the obstruction, the liftgate may be power opened or closed normally. If the liftgate encounters multiple obstacles on the same power cycle, the power function will deactivate, and the liftgate will switch to manual operation.
Page 84: Windows
Windows CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 85: Power Windows
Power Windows The power window switches are located on the armrest near each window. Press the up or down arrows on the switches to raise or lower the windows. Your vehicle has Retained Accessory Power (RAP) that allows you to use the power windows once the ignition has been turned off for up to 10 minutes.
Page 86 To program each front window, follow these steps: 1. With the ignition in ACCESSORY, ON, or when Retained Accessory Power (RAP) is active, close all doors. 2. Press and hold the down arrow on the power window switch until the window has fully opened. 3.
Page 87: Sun Visors
Window Lockout This feature allows you to disable the passenger window switches. The passenger window lockout button is located below the power window switches on the driver’s door armrest. Press the button to disable the passenger window controls. The light on the button will illuminate, indicating that the feature is in use.
Page 88: Theft-Deterrent Systems
Theft-Deterrent Systems Vehicle theft is big business, especially in some cities. Although your vehicle has a number of theft-deterrent features, we know that nothing we put on it can make it impossible to steal. Theft-Deterrent System The security light is located on the instrument panel cluster.
Page 89: Immobilizer
Testing the Alarm 1. From inside the vehicle, roll down the window, then get out of the vehicle, keeping the door open. 2. From outside of the vehicle, with the door open, lock the vehicle using the power door lock switch or the remote keyless entry transmitter and close the door.
Page 90: Immobilizer Operation
Immobilizer Operation Your vehicle is equipped with a passive theft-deterrent system. The system works when you turn the key to ON. The key uses a transponder that matches an immobilizer control unit in your vehicle. The correct key will start the vehicle.
Page 91: Starting And Operating Your Vehicle
Your vehicle is not protected by the theft-deterrent system at this time. In an emergency, contact Cadillac Roadside Service See Roadside Service on page 7-6. Starting and Operating Your Vehicle...
Page 92: Ignition Positions
Ignition Positions With the key in the ignition switch, you can turn the key to four different positions. Notice: If your key seems stuck in OFF and you can’t turn it, be sure you are using the correct key; if so, is it all the way in? If it is, then turn the steering wheel left and right while you turn the key hard.
Page 93: Retained Accessory Power (Rap)
Steering Column Ignition Lock Release If your vehicle has a dead battery or a battery with low voltage, you can still release the ignition lock and remove the key. Use the following procedure to release the steering column: 1. Locate the plastic screw head on the underside of the plastic cover for the steering column.
Page 94: Starting The Engine
Starting the Engine Move your shift lever to PARK (P) or NEUTRAL (N). Your engine will not start in any other position — that is a safety feature. To restart when you are already moving, use NEUTRAL (N) only. Notice: Do not try to shift to PARK (P) if your vehicle is moving.
Page 95: Engine Coolant Heater
Engine Coolant Heater Your vehicle may be equipped with an engine coolant heater. In very cold weather, 0°F ( 18°C) or colder, the engine coolant heater can help. You will get easier starting and better fuel economy during engine warm-up. Usually, the coolant heater should be plugged in a minimum of four hours prior to starting your vehicle.
Page 96: Automatic Transmission Operation
Automatic Transmission Operation The shift lever is located on the center console between the front seats. There are several different positions for the shift lever. PARK (P): This position locks the rear wheels. It is the best position to use when you start the engine because your vehicle cannot move easily.
Page 97 Ensure the shift lever is fully in PARK (P) before starting the engine. Your vehicle has an automatic transmission shift lock control system. You must fully apply your regular brakes before you can shift from PARK (P) when the ignition key is in ON. If you cannot shift out of PARK (P), ease pressure on the shift lever.
Page 98 AUTOMATIC OVERDRIVE (D): This position is for normal driving. If you need more power for passing, and you are: • Going less than 35 mph (55 km/h), push the accelerator pedal about halfway down. • Going about 35 mph (55 km/h) or more, push the accelerator all the way down.
Page 99: Parking Brake
2. Press the shift lever forward to upshift or rearward to downshift. The odometer on the instrument panel cluster will change from the mileage to a number indicating the requested gear range when moving the shift lever forward or rearward. See Speedometer and Odometer on page 3-35 for more information on the odometer.
Page 100: Shifting Into Park (P)
To release the parking brake, pull the release lever located to the left of the steering wheel on the instrument panel. Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts. Verify that the parking brake is fully released and the brake warning light is off before driving.
Page 101: Leaving Your Vehicle With The Engine Running
4. Turn the key to OFF. 5. Remove the key from the ignition switch and take it with you. If you can leave your vehicle with the key in your hand, the vehicle is in PARK (P). Leaving Your Vehicle With the Engine Running CAUTION: It can be dangerous to leave your vehicle with...
Page 102: Shift Lock Release
Shifting Out of Park (P) Your vehicle has an automatic transmission shift lock control system. You have to fully apply your regular brakes before you can shift from PARK (P) when the ignition is in ON. See Automatic Transmission Operation on page 2-26 for more information.
Page 103: Parking Over Things That Burn
Parking Over Things That Burn CAUTION: Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass or other things that can burn. Engine Exhaust CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell.
Page 104: Running The Engine While Parked
Running the Engine While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle.
Page 105: Mirrors
Mirrors Automatic Dimming Rearview Mirror ® with OnStar The vehicle may have an automatic dimming inside ® rearview mirror with OnStar controls. For more ® information about OnStar , see OnStar on page 2-40. (On/Off): The on/off button, located on the lower left side of the mirror, is used for the automatic dimming functions of the rearview mirror.
Page 106: Compass Calibration
Mirror Operation The automatic dimming feature comes on each time the vehicle is started. To turn the automatic dimming feature on or off, press the on/off button. The indicator light will illuminate when this feature is on. Compass Operation Press the on/off button once to turn the compass on or off.
Page 107 To adjust for compass variance, do the following: 1. Find your current location and variance zone number on the zone map that follows. 2. Press and hold the on/off button until a zone number appears on the display. 3. Once the zone number appears on the display, press the on/off button quickly until you reach the correct zone number.
Page 108: Outside Power Heated Mirrors
Outside Power Heated Mirrors The controls on the driver’s door armrest operate both outside rearview mirrors. Press the left or right mirror symbol on the selector control to choose the driver’s side or passenger’s side mirror. The center position is off and will not move the mirrors if the directional control pad is touched.
Page 109: Outside Automatic Dimming Mirror
Outside Automatic Dimming Mirror The driver’s outside mirror may have an automatic dimming feature that helps to reduce glare from other vehicles headlamps. This feature is controlled by the on and off settings on the automatic dimming rearview mirror. See Automatic Dimming Rearview Mirror with ®...
Page 110: Onstar System
® OnStar System ® OnStar uses global positioning system (GPS) satellite technology, wireless communications, and live advisors to provide you with a wide range of safety, security, information, and convenience services. If your airbags deploy, the system is designed to make an automatic call ®...
Page 111: Onstar Personal Calling
Directions and Connections Plan • Advanced Automatic Collision Notiﬁcation • Automatic Notiﬁcation of Airbag Deployment • Emergency Services • Roadside Assistance • Stolen Vehicle Tracking • AccidentAssist • Remote Door Unlock/Vehicle Alert • Remote Diagnostics • Online Concierge • Driving Directions •...
Page 112: Universal Home Remote System
Universal Home Remote System If your vehicle has this feature, the control buttons are located on the driver’s sun visor. The Universal Home Remote System, a combined universal transmitter and receiver, provides a way to replace up to three hand-held transmitters used to activate devices such as gate operators, garage door openers, entry door locks, security systems, and home lighting.
Page 113 Keep the original hand-held transmitter for use in other vehicles as well as for future Universal Home Remote programming. It is also recommended that upon the sale of the vehicle, the programmed Universal Home Remote buttons should be erased for security purposes. See “Erasing Universal Home Remote Buttons”...
Page 114: Gate Operator And Canadian Programming
If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with Steps 6 through 8 following to complete the programming of a rolling-code equipped device, most commonly, a garage door opener. 6. Locate in the garage, the garage door opener receiver (motor-head unit).
Page 115: Erasing Universal Home Remote Buttons
Using Universal Home Remote Press and hold the appropriate Universal Home Remote button for at least half of a second. The indicator light will come on while the signal is being transmitted. Erasing Universal Home Remote Buttons To erase programming from the three Universal Home Remote buttons do the following: 1.
Page 116: Storage Areas
Storage Areas Glove Box To open the glove box, lift up on the lever. Use your door key to lock or unlock it. Cupholder(s) Your vehicle has cupholders located between the front seats. Slide the cover back to expose them. There are also cupholders in the armrest of the second row seat.
Page 117: Luggage Carrier
Luggage Carrier CAUTION: If you try to carry something on top of your vehicle that is longer or wider than the luggage carrier — like paneling, plywood, a mattress and so forth — the wind can catch it as you drive along.
Page 118: Convenience Net
Convenience Net If your vehicle has a convenience net, the convenience net attaches to the ﬂoor or back wall of the rear of the vehicle using six anchor points. The net can be used like a hammock across the rear of the vehicle or hooked on the ﬂoor.
Page 119 The vehicle may have an UltraView sunroof over the ﬁrst two rows of seats. The ignition must be on, or in accessory, or the Retained Accessory Power (RAP) must be active for to operate it. See Retained Accessory Power (RAP) on page 2-23. The sunroof/sunshade switches are located in the headliner between the...
Page 120: Sunroof (Ultraview Plus)
Sunroof (UltraView Plus) CAUTION: People who are in a crash and not wearing a safety belt properly can suffer much worse injuries. They can hit things inside the vehicle or be ejected from it, and be seriously injured or killed. This is true for any vehicle occupant, in any motor vehicle, but if you have the Ultraview roof it is, if anything, even more important.
Page 121 Press the front of the sunroof switch to close the sunroof. Press the switch to the ﬁrst stop to close the sunroof to a desired position. Press the front of the switch to the second stop to express close the sunroof. Press the back of the front sunshade switch to open it.
Page 122: Vehicle Personalization
Vehicle Personalization In addition to the following features, your vehicle may also have features that can be programmed through the Driver Information Center (DIC). See DIC Vehicle Personalization on page 3-66 for more information. Memory Seat and Mirrors If your vehicle has the memory feature, you can program and recall memory settings for the driver’s seating and outside rearview mirror driving positions for up to two drivers.
Page 123 The vehicle must be in PARK (P) to recall the stored driving positions. Press one of the numbered memory buttons to recall the stored setting. Each time a memory button is pressed, a single beep will sound. Three chimes will sound and the setting will not be recalled if you press button 1 or 2 when the vehicle is not in PARK (P).
Page 124 NOTES 2-54...
Page 125 Section 3 Instrument Panel Overview ...3-4 Hazard Warning Flashers ...3-6 Other Warning Devices ...3-6 Horn ...3-6 Tilt Wheel ...3-7 Turn Signal/Multifunction Lever ...3-7 Turn and Lane-Change Signals ...3-8 Headlamp High/Low-Beam Changer ...3-8 Flash-to-Pass ...3-9 Windshield Wipers ...3-9 Windshield Washer ...3-10 Rear Window Wiper/Washer ...3-11 Headlamp Washer ...3-12 Cruise Control ...3-12...
Page 126 Section 3 Fog Lamp Light ...3-46 Lights On Reminder ...3-46 Cruise Control Light ...3-46 Highbeam On Light ...3-47 Fuel Gage ...3-47 Driver Information Center (DIC) ...3-48 System Controls ...3-48 Status of Vehicle Systems ...3-49 DIC Main Menu ...3-53 DIC Warnings and Messages ...3-57 DIC Vehicle Personalization ...3-66 Instrument Panel Audio System(s) ...3-80...
Page 127 NOTES...
Page 128: Instrument Panel Overview
Instrument Panel Overview...
Page 129 The main components of the instrument panel are the following: A. Air Outlets. See Outlet Adjustment on page 3-30. B. Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page 3-7. C. Steering Wheel Controls. See Audio Steering Wheel Controls on page 3-111. D.
Page 130: Hazard Warning Flashers
Hazard Warning Flashers Your hazard warning ﬂashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will ﬂash on and off. The hazard warning ﬂasher button is located in the center of the instrument panel.
Page 131: Tilt Wheel
Tilt Wheel A tilt wheel allows you to adjust the steering wheel before you drive. You can raise it to the highest level to give your legs more room when you exit and enter the vehicle. The lever that allows you to tilt the steering wheel is located on the left side of the steering column.
Page 132: Turn And Lane-Change Signals
Turn and Lane-Change Signals To signal a turn, move the lever all the way up or down. The lever returns automatically when the turn is complete. An arrow on the instrument panel cluster will ﬂash in the direction of the turn or lane change.
Page 133: Flash-To-Pass
Flash-to-Pass This feature allows you to use the high-beam headlamps to signal the driver in front of you that you want to pass. Pull and hold the turn signal/multifunction lever toward you to use this feature. When you do, the following will occur: •...
Page 134: Windshield Washer
(Low Speed): Put the lever in this position for slow, steady wiping cycles. (High Speed): Put the lever in this position for rapid wiping cycles. If the windshield wipers are in use for about six seconds while you are driving, the exterior lamps will come on automatically if the exterior lamp control is in AUTO.
Page 135: Rear Window Wiper/Washer
Rear Window Wiper/Washer CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ﬂuid can form ice on the windshield, blocking your vision. The switch for the rear washer/wiper is located in the overhead console. (Rear Wiper): Press this side of the button to turn the rear wiper on.
Page 136: Headlamp Washer
Headlamp Washer Your vehicle may have headlamp washers. The headlamp washers clear debris from the headlamp lenses. The headlamp washers are located to the inside of the headlamps. To wash the headlamps, press the washer button located at the end of the windshield wiper lever. Both the headlamps and the windshield will be washed.
Page 137 + (Resume/Accelerate): Push the lever to this symbol to make the vehicle resume to a previously set speed or to accelerate when cruise is already active. (Set/Decrease): Press this button to set the speed or to decrease the speed when cruise is already active.
Page 138: Setting Cruise Control
Setting Cruise Control CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control.
Page 139 Increasing Speed While Using Cruise Control There are two ways to go to a higher speed: • Use the accelerator pedal to get to the higher speed. Press the set button at the end of the lever, then release the button and the accelerator pedal.
Page 140: Headlamps
Ending Cruise Control To end a cruise control session, step lightly on the brake pedal. Stepping on the brake pedal will end the current cruise control session only. Move the cruise control switch to off to turn off the system completely. Erasing Speed Memory When you turn off the cruise control or the ignition, your cruise control set speed memory is erased.
Page 141: Headlamps On Reminder
Headlamps on Reminder A warning chime will sound if the exterior lamp control is left on in either the headlamp or parking lamp position and the driver’s door is opened with the ignition off. See Lights On Reminder on page 3-46 for additional information.
Page 142: Fog Lamps
To operate your vehicle with the DRL off, turn the exterior lamp control off. Then turn on the fog lamps or parking lamps, and the DRL will turn off. The Headlamps Suggested message will appear on the DIC display. This will work regardless of gear position and whether or not the parking brake is set.
Page 143: Exterior Lighting Battery Saver
Exterior Lighting Battery Saver If the parking lamps or headlamps have been left on, the exterior lamps will turn off about 10 minutes after the ignition is turned to OFF. This protects against draining the battery in case you have accidentally left the headlamps or parking lamps on.
Page 144: Parade Dimming
Parade Dimming This feature prohibits dimming of the instrument panel displays and backlighting during daylight hours when the key is in the ignition and the headlamps are on. This feature operates with the light sensor and is fully automatic. When the light sensor reads darkness outside and the parking lamps are active, the instrument panel displays can be adjusted by sliding the instrument panel brightness lever toward the symbol to brighten...
Page 145 CAUTION: Even with the Ultrasonic Rear Park Assist system, the driver must check carefully before backing up. The system does not operate above typical backing speeds of 3 mph (5 km/h) while parking. And, the system does not detect objects that are more than 5 feet (1.5 meters) behind the vehicle.
Page 146: How The System Works
How the System Works URPA comes on automatically when the shift lever is moved into REVERSE (R) and the vehicle speed is less than 3 mph (5 km/h). When the system turns on, the three lights on the display will illuminate for one and a half seconds to let you know that the system is working.
Page 147: Accessory Power Outlet(S)
Accessory Power Outlet(s) Your vehicle is equipped with accessory power outlets. The outlets can be used to plug in electrical equipment such as a cellular telephone, CB radio, etc. Your vehicle has one outlet in front of the center console on the instrument panel, one in the rear of the center console, one in the rear compartment, and there may be an additional outlet in the rear of the center console.
Page 148: Ashtray(S) And Cigarette Lighter
Ashtray(s) and Cigarette Lighter Your vehicle may have an ashtray and cigarette lighter. Notice: If you put papers, pins, or other ﬂammable items in the ashtray, hot cigarettes or other smoking materials could ignite them and possibly damage your vehicle. Never put ﬂammable items in the ashtray.
Page 149: Climate Controls
Climate Controls Dual Climate Control System With this system you can control the heating, cooling and ventilation for your vehicle. Automatic Operation AUTO (Automatic): When this button is pressed and the temperature is set, the system will automatically control the inside temperature, the air delivery mode, the air conditioning compressor and the fan speed.
Page 150: Manual Operation
You can switch from English to metric units through the Driver Information Center (DIC). If you have the Base audio system, see DIC Main Menu on page 3-53. If you have the Navigation system, see “Setup Menu” in the Navigation System Manual. The air-conditioning system removes moisture from the air, so you may sometimes notice a small amount of water dripping underneath your vehicle while idling...
Page 151 If the airﬂow seems low when the fan speed is at the highest setting, the passenger compartment air ﬁlter may need to be replaced. For more information, see Passenger Compartment Air Filter on page 3-32 and Scheduled Maintenance on page 6-4. (Recirculation): This mode keeps outside air from coming in the vehicle.
Page 152 Sensors There is a solar sensor located on the instrument panel, near the windshield. 3-28 There is also an interior temperature sensor located to the right of the steering wheel on the instrument panel. These sensors monitor the solar radiation and the air inside your vehicle, then use the information to maintain the selected temperature by initiating needed adjustments to the temperature, the fan speed and...
Page 153: Defogging And Defrosting
Defogging and Defrosting Fog on the inside of windows is a result of high humidity (moisture) condensing on the cool window glass. This can be minimized if the climate control system is used properly. There are two modes to clear fog from your windshield.
Page 154: Rear Window Defogger
Rear Window Defogger The rear window defogger uses a warming grid to remove fog or frost from the rear window. The rear window defogger will only work when the ignition is in ON. (Rear Window Defogger): Press this button to turn the rear window defogger on or off.
Page 155: Rear Air Conditioning System
Operation Tips • Clear away any ice, snow or leaves from the air inlets at the base of the windshield that may block the ﬂow of air into your vehicle. • Use of non-GM approved hood deﬂectors may adversely affect the performance of the system. •...
Page 156: Passenger Compartment Air Filter
Passenger Compartment Air Filter The passenger compartment air ﬁlter traps most of the pollen from the air entering your vehicle. Like your vehicle’s engine air cleaner/ﬁlter, it needs to be changed periodically. For how often to change the passenger compartment air ﬁlter, see Scheduled Maintenance on page 6-4.
Page 157: Warning Lights, Gages, And Indicators
Warning Lights, Gages, and Indicators This part describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement.
Page 158: Instrument Panel Cluster
Instrument Panel Cluster The instrument panel cluster is designed to let you know at a glance how your vehicle is running. You’ll know how fast you’re going, how much fuel you’re using and many of the other things you’ll need to know to drive safely and economically.
Page 159: Speedometer And Odometer
Speedometer and Odometer The speedometer lets you see your speed in either miles per hour (mph) or kilometers per hour (km/h). The odometer shows how far your vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada). If your vehicle has to have a new odometer installed, the new one may read the correct mileage.
Page 160: Tachometer
Tachometer This gage indicates the engine speed in revolutions per minute (rpm). Engine Speed Limiter This feature prevents the engine from operating at too many revolutions per minute (rpm). When the engine’s rpms are too high, the throttle is closed to reduce speed.
Page 161: Airbag Readiness Light
Airbag Readiness Light There is an airbag readiness light on the instrument panel, which shows the airbag symbol. The system checks the airbag’s electrical system for malfunctions. The light tells you if there is an electrical problem. The system check includes the airbag sensors, the airbag modules, the wiring and the diagnostic module.
Page 162: Charging System Light
Charging System Light When you turn the key to ON or START, this light will come on brieﬂy to show that the generator and battery charging systems are working properly. If this light stays on, your vehicle needs service. You should take your vehicle to the dealer at once.
Page 163: Anti-Lock Brake System
If the light comes on while you are driving, pull off the road and stop carefully. You may notice that the pedal is harder to push, or the pedal may go closer to the ﬂoor. It may take longer to stop. If the light is still on, have the vehicle towed for service.
Page 164: Traction Control System (Tcs)
Traction Control System (TCS) Warning Light If the TC (traction control) warning light comes on and stays on, there may be a problem with the traction control system. The TC (traction control) warning light will come on brieﬂy when you turn the ignition to ON. If it doesn’t come on then, have it ﬁxed so it will be ready to warn you if there is a problem.
Page 165: Engine Coolant Temperature Gage
Engine Coolant Temperature Gage This gage shows the engine coolant temperature. If the gage pointer moves into the shaded area, the engine is too hot. That reading means the same thing as the warning light – the engine coolant is very hot. See Engine Overheating on page 5-29.
Page 166: Malfunction Indicator Lamp
Malfunction Indicator Lamp Check Engine Light Your vehicle is equipped with a computer which monitors operation of the fuel, ignition, and emission control systems. This system is called OBD II (On-Board Diagnostics-Second Generation) and is intended to assure that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment.
Page 167: If The Light Is On Steady
This light should come on, as a check to show you it is working, when the ignition is on and the engine is not running. If the light does not come on, have it repaired. This light will also come on during a malfunction in one of two ways: •...
Page 168: Emissions Inspection And Maintenance Programs
Did you just drive through a deep puddle of water? If so, your electrical system may be wet. The condition will usually be corrected when the electrical system dries out. A few driving trips should turn the light off. Have you recently changed brands of fuel? If so, be sure to fuel your vehicle with quality fuel.
Page 169: Maintenance Schedule
Oil Pressure Light CAUTION: Do not keep driving if the oil pressure is low. If you do, your engine can become so hot that it catches ﬁre. You or others could be burned. Check your oil as soon as possible and have your vehicle serviced.
Page 170: Security Light
Security Light For information regarding this light, see Theft-Deterrent System on page 2-18. Fog Lamp Light The fog lamps light will come on when the fog lamps are in use. The light will go out when the fog lamps are turned off. See Fog Lamps on page 3-18 for more information.
Page 171: Highbeam On Light
Highbeam On Light This light comes on whenever the high-beam headlamps are on. See Headlamp High/Low-Beam Changer on page 3-8 for more information. Fuel Gage The fuel gage shows approximately how much fuel is in the tank. It works only when the ignition is in ON.
Page 172: Driver Information Center (Dic)
Driver Information Center (DIC) The DIC gives you the status of many of your vehicle’s systems. It is also used to display driver personalization features and warning/status messages. All messages will appear on the audio system display. If your vehicle has the Base audio system, use the information contained in this manual for instructions on operating the DIC for your vehicle.
Page 173: Vehicle Information Menu
Status of Vehicle Systems You can view the status of several vehicle systems using the DIC. Vehicle Information Menu To access this menu, press the up or down arrow on the INFO switch located to the right of the display. The following items are available when the ignition is in ON.
Page 174: Vehicle Information Menu Item Descriptions
Vehicle Information Menu Item Descriptions The following paragraphs contain a more detailed description of each menu item: OUTSIDE TEMP: If you select this item, the current outside temperature is displayed at the top of the screen. It will be in either degrees Fahrenheit (°F) or degrees Celsius (°C) depending upon whether the system is set for English or metric units.
Page 175 AVG MPH (AVG KM/H): If you select this item, the average speed of the vehicle is displayed in miles per hour (mph) or kilometers per hour (km/h). This average is calculated based on the various vehicle speeds recorded since the last reset of this menu item. To reset AVG MPH (AVG KM/H), press the CLR button located to the right of the screen.
Page 176 TRANS FLUID LIFE: If you select this item, the percentage of remaining transmission ﬂuid life is displayed. If you see 99% TRANS FLUID LIFE on the display, that means that 99% of the current transmission ﬂuid life remains. When the transmission ﬂuid life is depleted, the Change Trans Fluid message will appear on the display.
Page 177: Dic Main Menu
DIC Main Menu Accessing the DIC Main Menu To access the main menu of the DIC, do the following: 1. Press the TUNE/SEL knob once. 2. Turn the TUNE/SEL knob clockwise or counterclockwise to scroll through the menu items. The DIC main menu consists of the following menu items: •...
Page 178: Dic Main Menu Item Descriptions
DIC Main Menu Item Descriptions BASS - MID (Midrange) - TREBLE: This menu item allows you to adjust the levels for the bass, midrange, treble, balance, and fade features of the audio system. For more information, see “Setting the Tone (Bass/Treble)” and “Adjusting the Speakers (Balance/Fade)”...
Page 179 AUTOSTORE PRESETS: This menu item allows you to automatically store radio stations with the strongest signals as presets. See “Setting Preset Stations” under Radio with CD on page 3-82 for more information. CAT (Category): This menu item allows you to select radio stations based on preset categories.
Page 180 (English/Metric Units): Use this menu item to adjust the measurement units. You can choose between ENGLISH UNITS and METRIC UNITS. To switch between the two, press the TUNE/SEL knob. Once your choice is displayed, turn the knob to set your choice and continue scrolling through the main menu.
Page 181: Dic Warnings And Messages
DIC Warnings and Messages These messages will appear if there is a problem detected in one of your vehicle’s systems. You must acknowledge a message to clear it from the screen for further use. To clear a message, press the CLR button. Be sure to take any message that appears on the screen seriously and remember that clearing the message will only make the message disappear,...
Page 182: Battery Voltage Low
Battery Voltage Low This message will appear when the electrical system is charging less than 10 volts or if the battery has been drained. If this message appears immediately after starting the engine, it is possible that the generator can still recharge the battery.
Page 183: Check Brake Fluid
Check Brake Fluid This message will display if the ignition is in ON to inform the driver that the brake ﬂuid level is low. Have the brake system serviced by your GM dealer as soon as possible. See Brake System Warning Light on page 3-38 and Brakes on page 5-39 for more information.
Page 184: Engine Power Reduced
Engine Coolant Hot – AC (Air Conditioning) Off This message displays when the engine coolant becomes hotter than the normal operating temperature. To avoid added strain on a hot engine, the air conditioning compressor is automatically turned off. When the coolant temperature returns to normal, the air conditioning compressor will turn back on.
Page 185: Fuel Level Low
Fuel Level Low When this message appears on the display, it means that your vehicle is low on fuel. You should reﬁll the fuel tank as soon as possible. A single chime will sound when this message is displayed. Headlamps Suggested This message will appear when the amount of available light outside the vehicle is low and the exterior lamp control is off.
Page 186: Passenger Door Ajar
Passenger Door Ajar When this message appears on the display, it means that the passenger’s side front door was not closed completely. You should make sure that the door is closed completely. Right Rear Door Ajar When this message appears on the display, it means that the passenger’s side rear door was not closed completely.
Page 187: Service Idle Control
Service Idle Control A problem with the idle control has occurred when this message displays. Have your vehicle serviced by your GM dealer. Service Stability System This message will be displayed if there has been a problem detected with StabiliTrak If this message comes on while you are driving, pull off the road as soon as possible and stop carefully.
Page 188: Service Transmission
Service Transmission This message will display if there is a problem with the transmission of your vehicle. Have your vehicle serviced by your GM dealer. Service Vehicle Soon This message is displayed when a non-emissions related powertrain malfunction occurs. Have your vehicle serviced by your GM dealer as soon as possible.
Page 189: Traction Engaged
Starting Disabled – Throttle Problem This message appears when your vehicle’s throttle system is not functioning properly. Have your vehicle serviced by your GM dealer. Theft Attempted This message is displayed if the content theft-deterrent system has detected a break-in attempt while you were away from your vehicle.
Page 190: Dic Vehicle Personalization
DIC Vehicle Personalization Your vehicle has personalization that allows you to program certain features to a preferred setting for up to two people. The number of programmable features varies depending upon which model of the vehicle is purchased. On all vehicles, features such as climate control settings, radio preset settings, exterior lighting at unlock, remote lock and unlock conﬁrmation, and automatic door locks have already been programmed for...
Page 191: Personalization Features
Personalization Features The following choices are available for programming: Personalization Name This feature allows you to type in a name that will appear on the DIC display whenever the corresponding remote keyless entry transmitter is used or one of the buttons on the driver’s door armrest (1 or 2) is pressed.
Page 192 Remote Recall Memory If your vehicle has the optional memory package, you will have this feature. When this feature is turned on, you can recall any previously programmed seat, adjustable pedals, and mirror controls when the unlock button on the remote keyless entry transmitter is pressed. Programmable Modes Mode 1: ON Mode 2: OFF...
Page 193 To program the vehicle to a different mode, use the following procedure: 1. Enter the personalization portion of the SETUP menu following the instructions listed previously. 2. Turn the TUNE/SEL knob until REMOTE EXIT RECALL is highlighted. 3. Press the TUNE/SEL knob to switch back and forth between on and off.
Page 194 Auto Exit Seat If your vehicle has the optional memory package, you will have this feature. When this feature is turned on, you can recall any previously programmed exit position for the driver’s seat when the key is removed from the ignition and the driver’s door is opened.
Page 195 To determine the mode to which the vehicle is programmed or to program the vehicle to a different mode, use the following procedure: 1. Enter the personalization portion of the SETUP menu following the instructions listed previously. 2. Turn the TUNE/SEL knob until TWILIGHT DELAY is highlighted.
Page 196 Lights Flash at Lock This feature allows the exterior lamps to ﬂash once when the remote keyless entry transmitter is used to lock the vehicle. All doors must be closed for this feature to work, and the lamps will not ﬂash if the parking lamps or headlamps are on.
Page 197 To program the vehicle to a different mode, use the following procedure: 1. Enter the personalization portion of the SETUP menu following the instructions listed previously. 2. Turn the TUNE/SEL knob until HORN SOUNDS AT LOCK is highlighted. 3. Press the TUNE/SEL knob to switch back and forth between on and off.
Page 198 Driver Unlock in Park The feature allows the driver’s door to automatically unlock when the transmission is shifted into PARK (P). Programmable Modes Mode 1: ON Mode 2: OFF Before your vehicle was shipped from the factory, it was programmed to Mode 2. The mode to which the vehicle was programmed may have been changed since it left the factory.
Page 199 If this feature is selected, Driver Unlock in Park, Doors Unlock in Park, or Doors Unlock Key Out cannot be selected. The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.
Page 200: Delayed Locking
Doors Unlock Key Out This feature allows the doors to automatically unlock when the key is removed from the ignition. Programmable Modes Mode 1: ON Mode 2: OFF Before your vehicle was shipped from the factory, it was programmed to Mode 2. The mode to which the vehicle was programmed may have been changed since it left the factory.
Page 201 To program the vehicle to a different mode, use the following procedure: 1. Enter the personalization portion of the SETUP menu following the instructions listed previously. 2. Turn the TUNE/SEL knob until DELAYED LOCKING is highlighted. 3. Press the TUNE/SEL knob to switch back and forth between on and off.
Page 202 Mirror to Curb in Reverse If your vehicle has the optional memory package, you will have this feature. When this feature is turned on, the passenger’s outside rearview mirror will move downward so you can view the curb when the shift lever is shifted into REVERSE (R).
Page 203: Exiting The Personalization Menu
Enhanced Chime Volume This feature allows you to adjust the volume level of the vehicle’s warning chimes. The chime volume cannot be turned off, only adjusted. Programmable Modes Mode 1: NORMAL Mode 2: LOUD Before your vehicle was shipped from the factory, it was programmed to Mode 1.
Page 204: Audio System(S)
Audio System(s) Driving without distraction is a necessity for a safer driving experience. See Defensive Driving on page 4-2. By taking a few moments to read this manual and get familiar with your vehicle’s audio system, you can use it with less effort, as well as take advantage of its features.
Page 205: Setting The Time
Added sound equipment may interfere with the operation of your vehicle’s engine, radio, or other systems, and even damage them. Your vehicle’s systems may interfere with the operation of sound equipment that has been added. Notice: The chime signals related to seat belts, parking brake, and other functions of your vehicle operate through the GM radio/entertainment system.
Page 206: Radio With Cd
Radio with CD Radio with CD shown, Radio with Six-Disc CD similar 3-82 Radio Data System (RDS) The audio system has a Radio Data System (RDS). RDS features are available for use only on FM stations that broadcast RDS information. With RDS, the radio can do the following: •...
Page 207: Playing The Radio
XM™ Satellite Radio Service XM™ is a satellite radio service that is based in the 48 contiguous United States and in Canada (if available). XM™ offers over 100 coast-to-coast channels including music, news, sports, talk, and children’s programming. XM™ provides digital quality audio and text information, including song title and artist name.
Page 208: Finding A Station
3. Press the TUNE/SEL knob to turn AVC on or off. An X will appear in the box when AVC is selected on. 4. Press the CLR button to exit the display. To return to the original display, repeatedly press the CLR button or wait for the display to time out.
Page 209: Setting Preset Stations
Setting Preset Stations Up to 30 stations (six FM1, six FM2, and six AM, six XM1 and six XM2 (if equipped)), can be programmed on the six numbered ﬁrm keys, by performing the following steps: 1. Turn the radio on. 2.
Page 210 PRESETS HOME/AWAY: This feature gives you the ability to store two different kinds of station presets. HOME can be used for stations available where you live and AWAY can be for stations available outside of your local broadcasting area. To set preset stations for home and away perform the following steps: 1.
Page 211: Adjusting The Speakers (Balance/Fade)
AUDIO EQUALIZER: This feature allows you to select customized equalization settings. To choose an equalization setting (EQ0 through EQ5), perform the following steps: 1. Press the TUNE/SEL knob to enter the main menu. 2. Turn the TUNE/SEL knob until EQUALIZER appears on the display.
Page 212: Using Dsp
Using DSP Available only with the premium Bose this feature is used to provide a choice of ﬁve different listening experiences: DSP normal, talk, spacious, rear seat, and driver seat. DSP can be used while listening to the radio or the CD player. The radio keeps separate DSP settings for each band, preset, and source.
Page 213 MSG (Message): If the current RDS station has a message, MSG will appear on the display. The message may display the artist, song title, call in phone numbers, etc. If the entire message does not appear on the display, parts of the message will appear every three seconds until the message is completed.
Page 214: Rds And Xm
Activating Category (CAT) Stations (RDS and XM™) CAT allows you to search for stations with speciﬁc types of music. The selectable categories are POP, EASY, TALK, CNTRY (Country), CLASS (Classical), and JAZZ. To activate program types, perform the following steps: 1.
Page 215 Radio Display Message XL (Explicit Language XL on the radio display, Channels) after the channel name, indicates content with explicit language. XM Updating Updating encryption code No XM Signal Loss of signal Loading XM Acquiring channel audio (after 4 second delay) Channel Off Air Channel not in service Channel Unavail...
Page 216 Radio Display Message No CAT Info Category Name not available Not Found No channel available for the chosen category No Information No Text/Informational message available XM Lock Theft lock active XM Radio ID Radio ID label (channel 0) Unknown Radio ID not known (should only be if hardware failure) Check XM Receiver...
Page 217: Using The Single Cd Player
Using the Single CD Player Insert a CD partway into the slot, label side up. The player will pull it in. If the ignition and the radio are on the CD will begin playing. A CD may be loaded with the radio off but it will not start playing until the radio is on.
Page 218: Using The Six-Disc Cd Changer
F3 RDM (Random): Press this ﬁrm key to listen to the tracks in random, rather than sequential, order. RANDOM will appear on the display. Press RDM again to turn off random play. RANDOM will disappear from the display. F4 RPT (Repeat): Press this ﬁrm key to hear a track over again.
Page 219 Notice: If you add any label to a CD, insert more than one CD into the slot at a time, or attempt to play scratched or damaged CDs, you could damage the CD player. When using the CD player, use only CDs in good condition without any label, load one CD at a time, and keep the CD player and the loading slot free of foreign materials, liquids, and debris.
Page 220 CD REV (Reverse): Press this ﬁrm key to go to the previous track. Press and hold this ﬁrm key to reverse quickly within the track. Release the ﬁrm key to play the passage. The elapsed time of the track will appear on the display.
Page 221 CD Messages If the CD comes out, it could be for one of the following reasons: • If it is very hot. When the temperature returns to normal, the CD should play. • If you are driving on a very rough road. When the road becomes smoother, the CD should play.
Page 222: Navigation/Radio System
8. Turn the TUNE/SEL knob to ﬁnd the feature that you would like to store to the key. 9. Press the TUNE/SEL knob when you have found the feature to be stored. The display will update, by showing the symbol of the feature that you selected next to the conﬁgurable key.
Page 223: Stereo Rca Jacks
Each set of headphones has a volume knob. To adjust the volume, adjust this knob. The transmitters are located above the video display screen. The headphones will shut off to save battery power if they lose the signal from the system after about four minutes.
Page 224: Audio Output
How to Change the Video Format when in the Auxiliary Mode The auxiliary input video format is preset to NTSC. In some countries, the video format may be in PAL system. To change the video format, perform the following: 1. Connect to the red RCA jack. 2.
Page 225: Dvd Player
The RSE system is capable of outputting audio to the vehicle speakers by using the radio. The RSE system may be selected as an audio source on the radio if the RSE system power is on. Once the RSE system is selected as an audio source on the radio, adjust the speaker volume on the radio, if necessary.
Page 226 DVD Player Buttons (Power): Press this button to turn the RSE system on and off. (Eject): Press this button to eject a DVD or CD. SRCE (Source): Press this button to cycle through the available video modes. Auxiliary is available when an auxiliary device is plugged into the auxiliary jacks on the DVD faceplate.
Page 227: Playing A Disc
(Menu Navigation): Use the arrow keys to navigate through a menu. (Enter): Press this button to select items within a menu. If your vehicle is equipped with the navigation system, after pressing the SRCE button, the enter button can select all speaker or rear video. See the SRCE button previously for more information.
Page 228: Dvd Messages
Ejecting a Disc Press the eject button on the DVD player faceplate to eject the disc. There is not an eject button on the remote control. If a disc is ejected from the player, but is not removed, the DVD player will reload the disc within 25 to 30 seconds. The disc will be stored in the DVD player.
Page 229: Remote Control
Remote Control To use the remote control, aim it at the transmitter window above the video screen and press the desired button. Direct sunlight or very bright light may affect the ability of the RSE system to receive signals from the remote control.
Page 230 (Menu): Press this button to access the DVD main menu. (Display): Press this button to switch the video screen display features: color, contrast, brightness, tint, and display mode (normal, full, and zoom). Normal means the horizontal image is not stretched and the borders at the left and right of the picture are blank.
Page 231 (Angle): Press this button to open a menu that will operate only when a DVD is playing. The format and content of this function will vary for each disc. (Next): Press this button to go to the next chapter or track of a DVD or CD. (Previous): Press this button to go to the previous chapter or track of a DVD or CD.
Page 232 Battery Replacement To change the batteries, do the following: 1. Remove the battery compartment door located on the bottom of the remote control. 2. Replace the two AA batteries in the compartment. Make sure that they are installed correctly, using the diagram on the inside of the battery compartment.
Page 233 Tips and Troubleshooting Chart (cont’d) Problem Recommended Action The disc was ejected, The disc is being stored but it was pulled back in the DVD player. Press into the DVD player. the eject button again to eject the disc. In auxiliary mode, the Check the signal coming picture moves or scrolls.
Page 234: Dvd Distortion
Tips and Troubleshooting Chart (cont’d) Problem Recommended Action The auxiliary source is Press the MODE button running but there is no to change from the picture or sound. DVD player mode to the auxiliary source mode. Check to make sure that the auxiliary source is connected to the inputs properly.
Page 235: Theft-Deterrent Feature
Cleaning the DVD Player When cleaning the outside DVD faceplate and buttons, use only a clean cloth dampened with clean water. Cleaning the Video Screen Pour some isopropyl or rubbing alcohol on a clean cloth and gently wipe the video screen. Do not spray directly onto the screen and do not press too hard or too long on the video screen.
Page 236: Radio Reception
(Voice Recognition): If your vehicle has the navigation system, press this button to initiate voice recognition. See “Voice Recognition” in the Navigation System manual for more information. 1-6 (Preset Stations): Press this button to play stations that are programmed on the radio preset pushbuttons. The radio will only seek preset stations with a strong signal that are in the selected band.
Page 237: Care Of Your Cds And Dvds
FM Stereo FM stereo will give the best sound, but FM signals will reach only about 10 to 40 miles (16 to 65 km). Tall buildings or hills can interfere with FM signals, causing the sound to fade in and out. XM™...
Page 238: Diversity Antenna System
Diversity Antenna System The AM-FM antenna is integrated with the rear quarter glass windows, located in the rear of the vehicle on the driver and passenger sides. Make sure that the inside surface of the rear windows are not scratched and that the grid lines on the glass are not damaged.
Page 239: Driving Your Vehicle
Section 4 Your Driving, the Road, and Your Vehicle ...4-2 Defensive Driving ...4-2 Drunken Driving ...4-3 Control of a Vehicle ...4-5 Braking ...4-6 Anti-Lock Brake System (ABS) ...4-7 Braking in Emergencies ...4-8 Traction Control System (TCS) ...4-9 Magnetic Ride Control ...4-10 Limited-Slip Rear Axle ...4-10 ®...
Page 240: Your Driving, The Road, And Your Vehicle
Your Driving, the Road, and Your Vehicle Defensive Driving The best advice anyone can give about driving is: Drive defensively. Please start with a very important safety device in your vehicle: Buckle up. See Safety Belts: They Are for Everyone on page 1-11. CAUTION: Defensive driving really means “Be ready for anything.”...
Page 241: Drunken Driving
Drunken Driving Death and injury associated with drinking and driving is a national tragedy. It is the number one contributor to the highway death toll, claiming thousands of victims every year. Alcohol affects four things that anyone needs to drive a vehicle: •...
Page 242 It is the amount of alcohol that counts. For example, if the same person drank three double martinis (3 ounces or 90 ml of liquor each) within an hour, the person’s BAC would be close to 0.12 percent. A person who consumes food just before or during drinking will have a somewhat lower BAC level.
Page 243: Control Of A Vehicle
The body takes about an hour to rid itself of the alcohol in one drink. No amount of coffee or number of cold showers will speed that up. “I will be careful” is not the right answer. What if there is an emergency, a need to take sudden action, as when a child darts into the street? A person with even a moderate BAC might not be able to react quickly enough to avoid the collision.
Page 244: Braking
Braking See Brake System Warning Light on page 3-38. Braking action involves perception time and reaction time. First, you have to decide to push on the brake pedal. That is perception time. Then you have to bring up your foot and do it. That is reaction time. Average reaction time is about three-fourths of a second.
Page 245: Anti-Lock Brake System (Abs)
Anti-Lock Brake System (ABS) Your vehicle has anti-lock brakes. ABS is an advanced electronic braking system that will help prevent a braking skid. When you start your engine and begin to drive away, your anti-lock brake system will check itself. You may hear a momentary motor or clicking noise while this test is going on.
Page 246: Braking In Emergencies
The anti-lock system can change the brake pressure faster than any driver could. The computer is programmed to make the most of available tire and road conditions. This can help you steer around the obstacle while braking hard. As you brake, your computer keeps receiving updates on wheel speed and controls braking pressure accordingly.
Page 247: Traction Control System (Tcs)
Traction Control System (TCS) Your vehicle has a traction control system that limits wheel spin. This is especially useful in slippery road conditions. On a rear-wheel-drive vehicle, the system operates if it senses that one or both of the rear wheels are spinning or beginning to lose traction. On an All-Wheel-Drive (AWD) vehicle, the system will operate if it senses that any of the wheels are spinning or beginning to lose traction.
Page 248: Magnetic Ride Control
To turn the system off, press the TC (traction control) button located near the shift lever. If you press the TC (traction control) button once, the traction control system will turn off and the traction control system warning light will come on. Press the TC button again to turn the system back on.
Page 249: Stabilitrak System
® StabiliTrak System Your vehicle is equipped with a vehicle stability enhancement system called StabiliTrak advanced computer controlled system that assists you with directional control of the vehicle in difficult driving conditions. ® StabiliTrak activates when the computer senses a discrepancy between your intended path and the direction the vehicle is actually traveling.
Page 250: Power Steering
All-Wheel Drive (AWD) System If your vehicle is equipped with this feature, engine power is sent to all four wheels all the time. This is like four-wheel drive, but it is fully automatic. Steering Power Steering If you lose power steering assist because the engine stops or the system is not functioning, you can steer but it will take much more effort.
Page 251: Steering In Emergencies
Try to adjust your speed so you can “drive” through the curve. Maintain a reasonable, steady speed. Wait to accelerate until you are out of the curve, and then accelerate gently into the straightaway. Adding non-GM accessories can affect your vehicle’s performance.
Page 252: Off-Road Recovery
Off-Road Recovery You may ﬁnd that your right wheels have dropped off the edge of a road onto the shoulder while you are driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy. Ease off the accelerator and then, if there is nothing in the way, steer so that your vehicle straddles the edge of the pavement.
Page 253 • Do not get too close to the vehicle you want to pass while you are awaiting an opportunity. For one thing, following too closely reduces your area of vision, especially if you are following a larger vehicle. Also, you will not have adequate space if the vehicle ahead suddenly slows or stops.
Page 254: Loss Of Control
Loss of Control Let us review what driving experts say about what happens when the three control systems — brakes, steering, and acceleration — do not have enough friction where the tires meet the road to do what the driver has asked.
Page 255: Off-Road Driving
Off-Road Driving This off-road guide is for vehicles that have all-wheel drive. If your vehicle does not have all-wheel drive, you should not drive off-road unless you are on a level, solid surface. Many of the same design features that help make your vehicle responsive on paved roads during poor weather conditions —...
Page 256 Loading Your Vehicle for Off-Road Driving There are some important things to remember about how to load your vehicle. • The heaviest things should be on the load ﬂoor and forward of your rear axle. Put heavier items as far forward as you can.
Page 257: Environmental Concerns
Environmental Concerns Off-road driving can provide wholesome and satisfying recreation. However, it also raises environmental concerns. We recognize these concerns and urge every off-roader to follow these basic rules for protecting the environment: • Always use established trails, roads, and areas that have been specially set aside for public off-road recreational driving;...
Page 258: Scanning The Terrain
Controlling your vehicle is the key to successful off-road driving. One of the best ways to control your vehicle is to control your speed. Here are some things to keep in mind. At higher speeds: • You approach things faster and you have less time to scan the terrain for obstacles.
Page 259: Driving On Off-Road Hills
When you drive over obstacles or rough terrain, keep a ﬁrm grip on the steering wheel. Ruts, troughs, or other surface features can jerk the wheel out of your hands if you are not prepared. When you drive over bumps, rocks, or other obstacles, your wheels can leave the ground.
Page 260: Approaching A Hill
Approaching a Hill When you approach a hill, you need to decide if it is one of those hills that is just too steep to climb, descend, or cross. Steepness can be hard to judge. On a very small hill, for example, there may be a smooth, constant incline with only a small change in elevation where you can easily see all the way to the top.
Page 261 • Ease up on your speed as you approach the top of the hill. • Attach a ﬂag to the vehicle to make you more visible to approaching traffic on trails or hills. • Sound the horn as you approach the top of the hill to let opposing traffic know you are there.
Page 262: Driving Downhill
Here are some things you must not do if you stall, or are about to stall, when going up a hill. • Never attempt to prevent a stall by shifting into NEUTRAL (N) to rev-up the engine and regain forward momentum. This will not work. Your vehicle will roll backwards very quickly and you could go out of control.
Page 263 CAUTION: Heavy braking when going down a hill can cause your brakes to overheat and fade. This could cause loss of control and a serious accident. Apply the brakes lightly when descending a hill and use a low gear to keep vehicle speed under control.
Page 264: Driving Across An Incline
Driving Across an Incline Sooner or later, an off-road trail will probably go across the incline of a hill. If this happens, you have to decide whether to try to drive across the incline. Here are some things to consider: •...
Page 265: Stalling On An Incline
Stalling on an Incline If your vehicle stalls when you are crossing an incline, be sure you, and any passengers, get out on the uphill side, even if the door there is harder to open. If you get out on the downhill side and the vehicle starts to roll over, you will be right in its path.
Page 266 Driving in Mud, Sand, Snow, or Ice When you drive in mud, snow, or sand, the wheels will not get good traction. You cannot accelerate as quickly, turning is more difficult, and you will need longer braking distances. It is best to use a low gear when you are in mud — the deeper the mud, the lower the gear.
Page 267: Driving In Water
Driving in Water Heavy rain can mean ﬂash ﬂooding, and ﬂood waters demand extreme caution. Find out how deep the water is before you drive through it. If it is deep enough to cover your wheel hubs, axles, or exhaust pipe, do not try it — you probably will not get through.
Page 268: Driving At Night
After Off-Road Driving Remove any brush or debris that has collected on the underbody, chassis, or under the hood. These accumulations can be a ﬁre hazard. After operation in mud or sand, have the brake linings cleaned and checked. These substances can cause glazing and uneven braking.
Page 269 No one can see as well at night as in the daytime. But as we get older these differences increase. A 50-year-old driver may require at least twice as much light to see the same thing at night as a 20-year-old. What you do in the daytime can also affect your night vision.
Page 270: Driving In Rain And On Wet Roads
Driving in Rain and on Wet Roads Rain and wet roads can mean driving trouble. On a wet road, you cannot stop, accelerate, or turn as well because your tire-to-road traction is not as good as on dry roads. And, if your tires do not have much tread left, you will get even less traction.
Page 271: Driving Through Flowing Water
Hydroplaning Hydroplaning is dangerous. So much water can build up under your tires that they can actually ride on the water. This can happen if the road is wet enough and you are going fast enough. When your vehicle is hydroplaning, it has little or no contact with the road. Hydroplaning does not happen often.
Page 272: City Driving
City Driving One of the biggest problems with city streets is the amount of traffic on them. You will want to watch out for what the other drivers are doing and pay attention to traffic signals. 4-34 Here are ways to increase your safety in city driving: •...
Page 273: Freeway Driving
Freeway Driving Mile for mile, freeways — also called thruways, parkways, expressways, turnpikes, or superhighways — are the safest of all roads. But they have their own special rules. The most important advice on freeway driving is: Keep up with traffic and keep to the right. Drive at the same speed most of the other drivers are driving.
Page 274: Before Leaving On A Long Trip
When you want to leave the freeway, move to the proper lane well in advance. If you miss your exit, do not, under any circumstances, stop and back up. Drive on to the next exit. The exit ramp can be curved, sometimes quite sharply. The exit speed is usually posted.
Page 275: Highway Hypnosis
Highway Hypnosis Is there actually such a condition as highway hypnosis? Or is it just plain falling asleep at the wheel? Call it highway hypnosis, lack of awareness, or whatever. There is something about an easy stretch of road with the same scenery, along with the hum of the tires on the road, the drone of the engine, and the rush of the wind against the vehicle that can make you sleepy.
Page 276 If you drive regularly in steep country, or if you are planning to visit there, here are some tips that can make your trips safer and more enjoyable. See Off-Road Driving on page 4-17 for information about driving off-road. • Keep your vehicle in good shape.
Page 277: Winter Driving
Winter Driving Here are some tips for winter driving: • Have your vehicle in good shape for winter. • You may want to put winter emergency supplies in your vehicle. Also see Tires on page 5-53. Include an ice scraper, a small brush or broom, a supply of windshield washer ﬂuid, a rag, some winter outer clothing, a small shovel, a ﬂashlight, a red cloth, and a couple of reﬂective warning triangles.
Page 278: Driving On Snow Or Ice
Driving on Snow or Ice Most of the time, those places where your tires meet the road probably have good traction. However, if there is snow or ice between your tires and the road, you can have a very slippery situation. You will have a lot less traction, or grip, and will need to be very careful.
Page 279: If You Are Caught In A Blizzard
Your anti-lock brake system (ABS) improves your vehicle’s stability when you make a hard stop on a slippery road. Even though you have ABS, you will want to begin stopping sooner than you would on dry pavement. See Anti-Lock Brake System (ABS) on page 4-7.
Page 280 You can run the engine to keep warm, but be careful. 4-42 CAUTION: Snow can trap exhaust gases under your vehicle. This can cause deadly CO (carbon monoxide) gas to get inside. CO could overcome you and kill you. You cannot see it or smell it, so you might not know it is in your vehicle.
Page 281: If Your Vehicle Is Stuck In Sand, Mud, Ice Or Snow
Then, shut the engine off and close the window almost all the way to preserve the heat. Start the engine again and repeat this only when you feel really uncomfortable from the cold. But do it as little as possible. Preserve the fuel as long as you can. To help keep warm, you can get out of the vehicle and do some fairly vigorous exercises every half hour or so until help comes.
Page 282: Rocking Your Vehicle To Get It Out
Rocking Your Vehicle to Get It Out First, turn your steering wheel left and right. That will clear the area around your front wheels. If your ® vehicle has the StabiliTrak System, turn the system off by pressing and holding the Traction button so that the STABILITY SYS DISABLED message and the traction off light are illuminated on the instrument panel cluster.
Page 283: Loading Your Vehicle
Loading Your Vehicle It is very important to know how much weight your vehicle can carry. This weight is called the vehicle capacity weight and includes the weight of all occupants, cargo, and all nonfactory-installed options. Two labels on your vehicle show how much weight it may properly carry, the Tire and Loading Information label and the Certiﬁcation/Tire label.
Page 284: Steps For Determining Correct Load Limit
The Tire and Loading Information label also shows the size of the original equipment tires (C) and the recommended cold tire inﬂation pressures (D). For more information on tires and inﬂation see Tires on page 5-53 and Inﬂation - Tire Pressure on page 5-60. There is also important loading information on the vehicle Certiﬁcation/Tire label.
Page 285 Example 1 Item Description Vehicle Capacity Weight for Example 1 = Subtract Occupant Weight 150 lbs (68 kg) Available Occupant and Cargo Weight = Total Item 1,000 lbs (453 kg) 300 lbs (136 kg) 700 lbs (317 kg) Example 2 Description Vehicle Capacity 1,000 lbs (453 kg)
Page 286 Example 3 Item Description Vehicle Capacity Weight for Example 3 Subtract Occupant Weight 200 lbs (91 kg) Available Cargo Weight = Refer to your vehicle’s Tire and Loading Information label for speciﬁc information about your vehicle’s capacity weight and seating positions. The combined weight of the driver, passengers, and cargo should never exceed your vehicle’s capacity weight.
Page 287 The Certiﬁcation/Tire label also tells you the maximum weights for the front and rear axles, called Gross Axle Weight Rating (GAWR). To ﬁnd out the actual loads on your front and rear axles, you need to go to a weigh station and weigh your vehicle. Your dealer can help you with this.
Page 288: Towing
Towing Towing Your Vehicle Consult your dealer or a professional towing service if you need to have your disabled vehicle towed. See Roadside Service on page 7-6. If you want to tow your vehicle behind another vehicle for recreational purposes (such as behind a motorhome), see Recreational Vehicle Towing following.
Page 289: Level Control
Dolly Towing Notice: Towing an all-wheel-drive vehicle with all four wheels on the ground, or even with only two of its wheels on the ground, will damage drivetrain components. Do not tow an all-wheel-drive vehicle if any of its wheels will be on the ground. If your vehicle is a rear-wheel drive, it can be towed using a dolly.
Page 290: Towing A Trailer
Towing a Trailer CAUTION: If you do not use the correct equipment and drive properly, you can lose control when you pull a trailer. For example, if the trailer is too heavy, the brakes may not work well — or even at all.
Page 291: If You Do Decide To Pull A Trailer
If You Do Decide to Pull a Trailer If you do, here are some important points: • There are many different laws, including speed limit restrictions, having to do with trailering. Make sure your rig will be legal, not only where you live but also where you’ll be driving.
Page 292: Weight Of The Trailer Tongue
The GCWR for your vehicle should not be exceeded. You can ask your dealer for our trailering information or advice, or you can write us at: Cadillac Customer Assistance Center Cadillac Motor Car Division P.O. Box 33169 Detroit, MI 48232-5169...
Page 293 If you’re using a weight-carrying hitch or a weight-distributing hitch, the trailer tongue (A) should weigh 10-15 percent of the total loaded trailer weight (B). After you’ve loaded your trailer, weigh the trailer and then the tongue, separately, to see if the weights are proper. If they aren’t, you may be able to get them right simply by moving some items around in the trailer.
Page 294 But let’s say your speciﬁc vehicle is equipped with some of the latest options and you have a front seat passenger and two rear seat passengers with some luggage and gear in the vehicle as well. You may add 300 lbs (136 kg) to the front axle weight and 400 lbs (181 kg) to the rear axle weight.
Page 295: Safety Chains
Total Weight on Your Vehicle’s Tires Be sure your vehicle’s tires are inﬂated to the upper limit for cold tires. You’ll ﬁnd these numbers on the Certiﬁcation/Tire label. See Loading Your Vehicle on page 4-45. Then be sure you don’t go over the GVW limit for your vehicle, including the weight of the trailer tongue.
Page 296: Driving With A Trailer
Driving with a Trailer Towing a trailer requires a certain amount of experience. Before setting out for the open road, you’ll want to get to know your rig. Acquaint yourself with the feel of handling and braking with the added weight of the trailer. And always keep in mind that the vehicle you are driving is now a good deal longer and not nearly as responsive as your vehicle is by itself.
Page 297: Turn Signals When Towing A Trailer
Turn Signals When Towing a Trailer When you tow a trailer, your vehicle may need a different turn signal ﬂasher and/or extra wiring. Check with your dealer. The arrows on your instrument panel will ﬂash whenever you signal a turn or lane change.
Page 298: Maintenance When Trailer Towing
When You Are Ready to Leave After Parking on a Hill 1. Apply your regular brakes and hold the pedal down while you: • start your engine, • shift into a gear, and • release the parking brake. 2. Let up on the brake pedal. 3.
Page 299: Service And Appearance Care
Section 5 Service ...5-3 Accessories and Modiﬁcations ...5-3 California Proposition 65 Warning ...5-3 Doing Your Own Service Work ...5-4 Adding Equipment to the Outside of Your Vehicle ...5-5 Fuel ...5-5 Gasoline Octane ...5-5 Gasoline Speciﬁcations ...5-6 California Fuel ...5-6 Additives ...5-6 Fuels in Foreign Countries ...5-7 Filling the Tank ...5-8 Filling a Portable Fuel Container ...5-10...
Page 300 Section 5 Different Size Tires and Wheels ...5-68 Uniform Tire Quality Grading ...5-68 Wheel Alignment and Tire Balance ...5-70 Wheel Replacement ...5-70 Tire Chains ...5-71 If a Tire Goes Flat ...5-72 Changing a Flat Tire ...5-72 Removing the Spare Tire and Tools ...5-74 Removing the Flat Tire and Installing the Spare Tire ...5-76 Secondary Latch System ...5-81...
Page 301: Service
Service Your dealer knows your vehicle best and wants you to be happy with it. We hope you will go to your dealer for all your service needs. You will get genuine GM parts and GM-trained and supported service people. We hope you will want to keep your GM vehicle all GM.
Page 302: Doing Your Own Service Work
Doing Your Own Service Work CAUTION: You can be injured and your vehicle could be damaged if you try to do service work on a vehicle without knowing enough about it. • Be sure you have sufficient knowledge, experience, the proper replacement parts, and tools before you attempt any vehicle maintenance task.
Page 303: Adding Equipment To The Outside Of Your Vehicle
Adding Equipment to the Outside of Your Vehicle Things you might add to the outside of your vehicle can affect the airﬂow around it. This may cause wind noise and affect windshield washer performance. Check with your dealer before adding equipment to the outside of your vehicle.
Page 304: Gasoline Speciﬁcations
Gasoline Speciﬁcations At a minimum, gasoline should meet ASTM speciﬁcation D 4814 in the United States or CAN/CGSB-3.5 in Canada. Some gasolines may contain an octane-enhancing additive called methylcyclopentadienyl manganese tricarbonyl (MMT). General Motors recommends against the use of gasolines containing MMT. See Additives on page 5-6 for additional information.
Page 305: Fuels In Foreign Countries
Notice: Your vehicle was not designed for fuel that contains methanol. Do not use fuel containing methanol. It can corrode metal parts in your fuel system and also damage the plastic and rubber parts. That damage would not be covered under your warranty.
Page 306: Filling The Tank
Filling the Tank CAUTION: Fuel vapor burns violently and a fuel ﬁre can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off your engine when you are refueling. Do not smoke if you are near fuel or refueling your vehicle.
Page 307 While refueling, hang the tethered fuel cap from the hook on the fuel door. CAUTION: If you spill fuel and then something ignites it, you could be badly burned. Fuel can spray out on you if you open the fuel cap too quickly. This spray can happen if your tank is nearly full, and is more likely in hot weather.
Page 308: Filling A Portable Fuel Container
Filling a Portable Fuel Container CAUTION: Never ﬁll a portable fuel container while it is in your vehicle. Static electricity discharge from the container can ignite the gasoline vapor. You can be badly burned and your vehicle damaged if this occurs. To help avoid injury to you and others: •...
Page 309: Hood Release
Hood Release To open the hood, do the following: 1. Pull the hood release lever with this symbol on it. It is located inside the vehicle on the lower left side of the instrument panel. 2. Then go to the front of the vehicle and ﬁnd the secondary hood release lever.
Page 310: Engine Compartment Overview
Engine Compartment Overview When you open the hood on the 3.6L V6 engine, you will see the following: 5-12...
Page 311 A. Underhood Fuse Block. See Underhood Fuse Block on page 5-97. B. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 5-38. C. Battery. See Battery on page 5-42. D. Passenger Compartment Air Filter. See Passenger Compartment Air Filter on page 3-32.
Page 312 When you open the hood on the 4.6L V8 engine, you will see the following: 5-14...
Page 313 A. Underhood Fuse Block. See Underhood Fuse Block on page 5-97. B. Battery. See Battery on page 5-42. C. Passenger Compartment Air Filter. See Passenger Compartment Air Filter on page 3-32. D. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 5-38.
Page 314: Engine Oil
Engine Oil Your vehicle may have an oil pressure light on the instrument cluster. There is also an Oil Pressure Low — Stop Engine message on the Driver Information Center (DIC). If the light and/or message appears on the instrument cluster, it means you need to check your engine oil level right away.
Page 315: When To Add Engine Oil
When to Add Engine Oil V6 Engine V8 Engine If the oil is below the cross-hatched area at the tip of the dipstick, you will need to add at least one quart/liter of oil. But you must use the right kind. This section explains what kind of oil to use.
Page 316: What Kind Of Engine Oil To Use
What Kind of Engine Oil to Use For V6 Engine Vehicles Only 5-18 Look for two things: • GM6094M Your vehicle’s engine requires oil meeting GM Standard GM6094M. You should look for and use only an oil that meets GM Standard GM6094M. •...
Page 317 Oils meeting these requirements should also have the starburst symbol on the container. This symbol indicates that the oil has been certiﬁed by the American Petroleum Institute (API). You should look for this information on the oil container, and use only those oils that are identiﬁed as meeting GM Standard GM6094M and have the starburst symbol on the front of the oil container.
Page 318 For V8 Engine Vehicles Only 5-20 Look for two things: • GM4718M Your vehicle’s engine requires a special oil meeting GM Standard GM4718M. Oils meeting this standard may be identiﬁed as synthetic. However, not all synthetic oils will meet this GM standard.
Page 319: Engine Oil Additives
Oils meeting these requirements should also have the starburst symbol on the container. This symbol indicates that the oil has been certiﬁed by the American Petroleum Institute (API). You should look for this on the oil container, and use only those oils that are identiﬁed as meeting GM Standard GM4718M and have the starburst symbol on the front of the oil container.
Page 320: Engine Oil Life System
Engine Oil Life System When to Change Engine Oil Your vehicle has a computer system that lets you know when to change the engine oil and ﬁlter. This is based on engine revolutions and engine temperature, and not on mileage. Based on driving conditions, the mileage at which an oil change will be indicated can vary considerably.
Page 321: Base Audio System
Base Audio System Press the CLR button located to the right of the DIC display to acknowledge the Change Engine Oil message. This will clear the message from the display and reset it. To reset the oil life indicator, use the following steps: 1.
Page 322: Engine Air Cleaner/Filter
Engine Air Cleaner/Filter 4.6L V8 shown, 3.6L V6 similar The engine air cleaner/ﬁlter is in the engine compartment on the driver’s side of the vehicle, near the front. See Engine Compartment Overview on page 5-12 for more information on location. 5-24 When to Inspect the Engine Air Cleaner/Filter...
Page 323: Automatic Transmission Fluid
4. The two sides of the airbox are hinged at the bottom. Open the airbox by pushing the top of the airbox cover toward the engine. 5. Remove the air ﬁlter by lifting it straight up through the opening in the airbox. 6.
Page 324: Engine Coolant
How to Reset the Change Transmission Fluid Message and the Transmission Fluid Indicator After the transmission ﬂuid has been changed, the Change Trans Fluid message and the transmission ﬂuid life indicator must be reset. To reset the message and indicator, use one of the following procedures: Base Audio System Press the CLR (Clear) button located to the right of the Driver Information Center (DIC) display to acknowledge...
Page 325: What To Use
Notice: Using coolant other than DEX-COOL cause premature engine, heater core, or radiator corrosion. In addition, the engine coolant may require changing sooner, at the ﬁrst maintenance service after each 25,000 miles (41 500 km) or 24 months, whichever occurs ﬁrst. Any repairs would not be covered by your warranty.
Page 326: Checking Coolant
Checking Coolant The coolant surge tank and pressure cap are located on the driver’s side of the vehicle, toward the rear of the engine compartment. See Engine Compartment Overview on page 5-12 for more information on location. 5-28 CAUTION: Turning the surge tank pressure cap when the engine and radiator are hot can allow steam and scalding liquids to blow out and burn you badly.
Page 327: Coolant Surge Tank Pressure Cap
Adding Coolant If you need more coolant, add the proper DEX-COOL coolant mixture at the surge tank, but only when the engine is cool. CAUTION: You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol, and it will burn if the engine parts are hot enough.
Page 328: If Steam Is Coming From Your Engine
If Steam Is Coming From Your Engine CAUTION: Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Just turn it off and get everyone away from the vehicle until it cools down.
Page 329: Overheated Engine Protection Operating Mode
If you get the overheat warning with no sign of steam, try this for a minute or so: 1. In heavy traffic, let the engine idle in NEUTRAL (N) while stopped. If it is safe to do so, pull off the road, shift to PARK (P) or NEUTRAL (N) and let the engine idle.
Page 330: Cooling System
Cooling System When you decide it is safe to lift the hood, here is what you will see: 3.6L V6 shown, 4.6L V8 similar A. Electric Engine Cooling Fans B. Coolant Surge Tank and Pressure Cap 5-32 Some vehicles may be equipped with an engine driven fan, as well as the electric pusher fans (A) which are located behind the vehicle’s grille.
Page 331 When the engine is cold, the coolant level should be at or slightly above the FULL COLD/FROID line on the side of the coolant surge tank. If it is not, you may have a leak at the pressure cap or in the radiator hoses, heater hoses, radiator, water pump or somewhere else in the cooling system.
Page 332: How To Add Coolant To The Coolant Surge Tank
How to Add Coolant to the Coolant Surge Tank If you have not found a problem yet, check to see if coolant is visible in the surge tank. If coolant is visible but the coolant level is not at the FULL COLD/FROID line on the side of the coolant surge tank, add a 50/50 mixture of clean, drinkable water and DEX-COOL coolant at the coolant surge tank, but be sure the...
Page 333 CAUTION: You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine. If no coolant is visible in the surge tank, add coolant as follows: 1.
Page 334 3. Fill the coolant surge tank with the proper mixture, to slightly above the FULL COLD/FROID line on the side of the coolant surge tank. 5-36 4. With the coolant surge tank pressure cap off, start the engine and let it run until you can feel the upper radiator hose getting hot.
Page 335: Power Steering Fluid
Power Steering Fluid See Engine Compartment Overview on page 5-12 for reservoir location. When to Check Power Steering Fluid It is not necessary to regularly check power steering ﬂuid unless you suspect there is a leak in the system or you hear an unusual noise.
Page 336: Windshield Washer Fluid
Windshield Washer Fluid What to Use When you need windshield washer ﬂuid, be sure to read the manufacturer’s instructions before use. If you will be operating your vehicle in an area where the temperature may fall below freezing, use a ﬂuid that has sufficient protection against freezing.
Page 337: Brakes
Brakes Brake Fluid Your brake master cylinder reservoir is ﬁlled with DOT-3 brake ﬂuid. See Engine Compartment Overview on page 5-12 for the location of the reservoir. There are only two reasons why the brake ﬂuid level in the reservoir might go down. The ﬁrst is that the brake ﬂuid goes down to an acceptable level during normal brake lining wear.
Page 338: Checking Brake Fluid
Checking Brake Fluid You can check the brake ﬂuid without taking off the cap. Look at the brake ﬂuid reservoir. The ﬂuid level should be above MIN. If it is not, have your brake system checked to see if there is a leak. After work is done on the brake hydraulic system, make sure the level is above the MIN but not over the MAX mark.
Page 339: Brake Adjustment
Brake Wear Your vehicle has four-wheel disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound may come and go or be heard all the time your vehicle is moving, except when you are pushing on the brake pedal ﬁrmly.
Page 340: Battery
Battery Your vehicle has a maintenance free battery. When it is time for a new battery, get one that has the replacement number shown on the original battery’s label. We recommend an ACDelco battery. See Engine Compartment Overview on page 5-12 for battery location. Warning: Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause...
Page 341 1. Check the other vehicle. It must have a 12-volt battery with a negative ground system. Notice: If the other vehicle’s system is not a 12-volt system with a negative ground, both vehicles can be damaged. Only use vehicles with 12-volt systems with negative grounds to jump start your vehicle.
Page 342 Your vehicle has a remote negative ( ) ground location, as shown in the illustration. It is located between the battery and the underhood fuse block. You should always use this remote ground location, instead of the terminal on the battery. 5-44 Notice: If you connect a negative cable to the ECM, ECM mounting bracket, or any cables that attach...
Page 343 CAUTION: Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a ﬂashlight if you need more light. Be sure the battery has enough water. You do not need to add water to the battery installed in your new vehicle.
Page 344 6. Connect the red positive (+) cable to the positive (+) terminal of the dead battery. Use a remote positive (+) terminal if the vehicle has one. 7. Do not let the other end touch metal. Connect it to the positive (+) terminal of the good battery. Use a remote positive (+) terminal if the vehicle has one.
Page 345 Jumper Cable Removal A. Heavy, Unpainted Metal Engine Part or Remote Negative ( ) Terminal B. Good Battery or Remote Positive (+) and Remote Negative ( ) Terminals C. Dead Battery or Remote Positive (+) Terminal To disconnect the jumper cables from both vehicles, do the following: 1.
Page 346: All-Wheel Drive
All-Wheel Drive All of the lubricant checks in this section apply to your vehicle. If you have an all-wheel-drive vehicle, there is an additional system that need lubrication. Transfer Case When to Check Lubricant It is not necessary to regularly check the transfer case ﬂuid unless you suspect there is a leak or you hear an unusual noise.
Page 347: Rear Axle
Rear Axle When to Check Lubricant It is not necessary to regularly check rear axle ﬂuid unless you suspect there is a leak or you hear an unusual noise. A ﬂuid loss could indicate a problem. Have it inspected and repaired. How to Check Lubricant To get an accurate reading, the vehicle should be on a level surface.
Page 348: Front Axle
Front Axle When to Check and Change Lubricant It is not necessary to regularly check the front axle ﬂuid unless you suspect there is a leak or you hear an unusual noise. A ﬂuid loss could indicate a problem. Have it inspected and repaired. How to Check Lubricant A.
Page 349: Halogen Bulbs
Your vehicle may have HID headlamps. After your vehicle’s HID headlamp bulb has been replaced, you may notice that the beam is a slightly different shade than it was originally. This is normal. Halogen Bulbs CAUTION: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb.
Page 350 4. Lift the wiper blade assembly up so it is in a T-shaped position. You should be able to see a tab. 5. Squeeze the tab together and pull the wiper blade assembly down far enough to release it from the J-hooked end of the wiper arm.
Page 351: Tires
Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your GM Warranty booklet for details. For additional information refer to the tire manufacturer’s booklet included with your vehicle’s Owner’s Manual.
Page 352: Winter Tires
Winter Tires If you expect to drive on snow or ice covered roads often, you may want to get winter tires for your vehicle. All season tires provide good overall performance on most surfaces but they may not offer the traction you would like or the same level of performance as winter tires on snow or ice covered roads.
Page 353 (A) Tire Size: The tire size is a combination of letters and numbers used to deﬁne a particular tire’s width, height, aspect ratio, construction type and service description. See the “Tire Size” illustration later in this section for more detail. (B) TPC Spec (Tire Performance Criteria Speciﬁcation): Original equipment tires designed to GM’s speciﬁc tire performance criteria have a TPC...
Page 354 Compact Spare Tire Example (A) Temporary Use Only: The compact spare tire or temporary use tire has a tread life of approximately 3,000 miles (5 000 km) and should not be driven at speeds over 65 mph (105 km/h). The compact spare tire is for emergency use when a regular road tire has lost air and gone ﬂat.
Page 355: Tire Size
Tire Size The following illustration shows an example of a typical passenger vehicle tire size. (A) Passenger (P-Metric) Tire: The United States version of a metric tire sizing system. The letter P as the ﬁrst character in the tire size means a passenger vehicle tire engineered to standards set by the U.S.
Page 356: Tire Terminology And Deﬁnitions
Tire Terminology and Deﬁnitions Air Pressure: The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight: This means the combined weight of optional accessories.
Page 357 Load Index: An assigned number ranging from 1 to 279 that corresponds to the load carrying capacity of a tire. Maximum Inﬂation Pressure: The maximum air pressure to which a cold tire may be inﬂated. The maximum air pressure is molded onto the sidewall. Maximum Load Rating: The load rating for a tire at the maximum permissible inﬂation pressure for that tire.
Page 358: Inﬂation - Tire Pressure
UTQGS (Uniform Tire Quality Grading Standards): A tire information system that provides consumers with ratings for a tire’s traction, temperature, and treadwear. Ratings are determined by tire manufacturers using government testing procedures. The ratings are molded into the sidewall of the tire. See Uniform Tire Quality Grading on page 5-68.
Page 359: How To Check
A Tire and Loading Information label is attached to the vehicle’s center pillar, below the driver’s door latch. This label lists your vehicle’s original equipment tires and shows the correct inﬂation pressures for your tires when they are cold. The recommended cold tire inﬂation pressure, shown on the label, is the minimum amount of air pressure needed to support your vehicle’s maximum load carrying capacity.
Page 360: Tire Pressure Monitor System
High Speed Operation CAUTION: Driving at high speeds, 100 mph (160 km/h) or higher, puts an additional strain on tires. Sustained high-speed driving causes excessive heat build up and can cause sudden tire failure. You could have a crash and you or others could be killed.
Page 361 Using the Driver Information Center (DIC), tire pressure levels can be viewed by the driver. For additional information and details about the DIC operation and displays see System Controls on page 3-48 and DIC Warnings and Messages on page 3-57. When a low tire pressure condition is detected, the TPM system will display the CHECK TIRE PRESSURE warning message on the DIC and, at the same time, illuminate...
Page 362 TPM Sensor Identiﬁcation Codes Each TPM sensor has a unique identiﬁcation code. Any time you replace one or more of the TPM sensors, the identiﬁcation codes will need to be matched to the new tire/wheel position. Each tire/wheel position is matched, to a sensor, by increasing or decreasing the tire’s air pressure.
Page 363: Tire Inspection And Rotation
10. After hearing the conﬁrming double horn chirp, for the left rear tire, exit the matching process by turning the ignition switch to OFF. 11. Set all four tires to the recommended air pressure level as indicated on the tire and loading information label.
Page 364: When It Is Time For New Tires
When It Is Time for New Tires One way to tell when it is time for new tires is to check the treadwear indicators, which will appear when your tires have only 1/16 inch (1.6 mm) or less of tread remaining. Some commercial truck tires may not have treadwear indicators.
Page 365 CAUTION: Mixing tires could cause you to lose control while driving. If you mix tires of different sizes (other than those originally installed on your vehicle), brands, or types (radial and bias-belted tires), the vehicle may not handle properly, and you could have a crash.
Page 366: Different Size Tires And Wheels
Different Size Tires and Wheels If you add wheels or tires that are a different size than your original equipment wheels and tires, this may affect the way your vehicle performs, including its braking, ride and handling characteristics, stability and resistance to rollover.
Page 367 Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a speciﬁed government test course. For example, a tire graded 150 would wear one and a half (1.5) times as well on the government course as a tire graded 100.
Page 368: Wheel Alignment And Tire Balance
Wheel Alignment and Tire Balance The tires and wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing will not be necessary on a regular basis. However, if you notice unusual tire wear or your vehicle pulling to one side or the other, the alignment may need to be checked.
Page 369: Tire Chains
CAUTION: Using the wrong replacement wheels, wheel bolts or wheel nuts on your vehicle can be dangerous. It could affect the braking and handling of your vehicle, make your tires lose air and make you lose control. You could have a collision in which you or others could be injured.
Page 370: If A Tire Goes Flat
If a Tire Goes Flat It is unusual for a tire to blowout while you are driving, especially if you maintain your vehicle’s tires properly. If air goes out of a tire, it is much more likely to leak out slowly.
Page 371 CAUTION: Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people. You and they could be badly injured or even killed. Find a level place to change your tire. To help prevent the vehicle from moving: 1.
Page 372: Removing The Spare Tire And Tools
Removing the Spare Tire and Tools The equipment you will need is located in the rear of the vehicle. To access the equipment, do the following: 1. Remove the storage bin to access the jack if your vehicle has the cargo management system. If your vehicle has the third row seat, remove the head rest storage tray to access the jack.
Page 373 4. Turn the wheel wrench counterclockwise to lower the spare tire to the ground. Continue turning the wrench until the spare tire (D) can be pulled out from under the vehicle. 5. Tilt the retainer (C) and slip it through the wheel opening to remove the spare tire from the cable (B).
Page 374: Removing The Flat Tire And Installing The Spare Tire
Removing the Flat Tire and Installing the Spare Tire To remove the ﬂat tire and install the spare, do the following: 1. Loosen the wheel nuts, but do not remove them yet, using the wheel wrench. Turn the handle about 180 degrees, then ﬂip the handle back to the starting position.
Page 375 CAUTION: Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. To help avoid personal injury and vehicle damage, be sure to ﬁt the jack lift head into the proper location before raising the vehicle.
Page 376 7. Raise the vehicle by turning the wheel wrench clockwise. Raise the vehicle far enough off the ground for the compact spare tire to ﬁt under the vehicle. 5-78 8. Remove all the wheel nuts and take off the ﬂat tire. CAUTION: Rust or dirt on the wheel, or on the parts to which it is fastened, can make the wheel nuts...
Page 377 CAUTION: Never use oil or grease on studs or nuts. If you do, the nuts might come loose. Your wheel could fall off, causing a serious accident. 9. Remove any rust or dirt from the wheel bolts, mounting surfaces and spare wheel. 10.
Page 378 CAUTION: Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to come loose and even come off. This could lead to an accident. Be sure to use the correct wheel nuts. If you have to replace them, be sure to get new GM original equipment wheel nuts.
Page 379: Secondary Latch System
Secondary Latch System Your vehicle has an underbody mounted tire hoist assembly equipped with a secondary latch system. It is designed to stop the compact spare tire from suddenly falling off your vehicle if the cable holding the spare tire is damaged. For the secondary latch to work, the tire must be stowed with the valve stem pointing down.
Page 380 3. Attach the wheel wrench to the jack and raise the jack at least 10 turns. 4. Place the jack under the vehicle, ahead of the rear bumper. Position the center lift point of the jack under the center of the spare tire. 5.
Page 381: Storing A Flat Or Spare Tire And Tools
Storing a Flat or Spare Tire and Tools CAUTION: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place. Storing the Flat Tire with Third Row Passengers 1.
Page 382: Storing The Spare Tire And Tools
Storing the Flat Tire with a Flat Load Floor 1. Put back all tools as they were stored in the rear storage compartment and put the compartment cover back on. 2. Place the ﬂat tire in the tire storage bag and put the tire in a horizontal position on the ﬂoor in the rear of the vehicle.
Page 383 3. Tilt the retainer downward and slip it through the center hole of the spare tire. Makesure the retainer is fully seated across the underside of the wheel. 4. Attach the wheel wrench to the hoist shaft. 5. Turn the wheel wrench clockwise to lift the spare tire.
Page 384: Compact Spare Tire
Compact Spare Tire Although the compact spare tire was fully inﬂated when the vehicle was new, it can lose air after a time. Check the inﬂation pressure regularly. It should be 60 psi (420 kPa). After installing the compact spare on the vehicle, you should stop as soon as possible and make sure the spare tire is correctly inﬂated.
Page 385: Appearance Care
Appearance Care Cleaning the Inside of Your Vehicle Your vehicle’s interior will continue to look its best if it is cleaned often. Although not always visible, dust and dirt can accumulate on your upholstery. Dirt can damage carpet, fabric, leather, and plastic surfaces. Regular vacuuming is recommended to remove particles from your upholstery.
Page 386: Fabric/Carpet
Do not clean your vehicle using the following cleaners or techniques: • Never use a knife or any other sharp object to remove a soil from any interior surface. • Never use a stiff brush. It can cause damage to your vehicle’s interior surfaces.
Page 387: Leather
If any of the soil remains, a commercial fabric cleaner or spot lifter may be necessary. When a commercial upholstery cleaner or spot lifter is to be used, test a small hidden area for colorfastness ﬁrst. If the locally cleaned area gives any impression that a ring formation may result, clean the entire surface.
Page 388: Wood Panels
Wood Panels Use a clean cloth moistened in warm, soapy water (use mild dish washing soap). Dry the wood immediately with a clean cloth. Speaker Covers Vacuum around a speaker cover gently, so that the speaker will not be damaged. Clean spots with just water and mild soap.
Page 389: Cleaning Exterior Lamps/Lenses
Cleaning Exterior Lamps/Lenses Use only lukewarm or cold water, a soft cloth and a car washing soap to clean exterior lamps and lenses. Follow instructions under Washing Your Vehicle on page 5-90. Finish Care Occasional waxing or mild polishing of the vehicle by hand may be necessary to remove residue from the paint ﬁnish.
Page 390: Aluminum Or Chrome-Plated Wheels
Aluminum or Chrome-Plated Wheels The vehicle may be equipped with either aluminum or chrome-plated wheels. Keep the wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel. A wax may then be applied.
Page 391: Sheet Metal Damage
Sheet Metal Damage If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection. Original manufacturer replacement parts will provide the corrosion protection while maintaining the warranty. Finish Damage Any stone chips, fractures or deep scratches in the ﬁnish should be repaired right away.
Page 392: Vehicle Care/Appearance Materials
Vehicle Care/Appearance Materials Description Polishing Cloth Interior and exterior Wax-Treated polishing cloth. Tar and Road Removes tar, road oil, Oil Remover and asphalt. Chrome Cleaner Use on chrome or and Polish stainless steel. White Sidewall Removes soil and black Tire Cleaner marks from whitewalls.
Page 393: Vehicle Identiﬁcation
Vehicle Identiﬁcation Vehicle Identiﬁcation Number (VIN) This is the legal identiﬁer for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver’s side. You can see it if you look through the windshield from outside your vehicle.
Page 394: Electrical System
Electrical System Add-On Electrical Equipment Notice: Don’t add anything electrical to your vehicle unless you check with your dealer ﬁrst. Some electrical equipment can damage your vehicle and the damage wouldn’t be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should.
Page 395: Underhood Fuse Block
Underhood Fuse Block The underhood fuse block is located in the engine compartment on the passenger’s side of the vehicle. See Engine Compartment Overview on page 5-12 for more information on location. To access the fuses, push in the two tabs located on each side of the fuse block cover.
Page 396 Relays PARK LAMP RELAY MICRO Parking Lamps HORN RELAY Horn MICRO HI BEAM RELAY MICRO High-Beam Headlamps DRL RELAY Daytime Running Lamps MICRO-OPT LO BEAM RELAY/HID Low-Beam HID Headlamps (Option) MINI-OPT HDLP WASH RELAY Headlamp Washer Motor (Option) MINI-OPT SPARE Not Used BLOWER Front Blower...
Page 397 J Cases Usage LOW FAN Low Cooling Fan Motor BLOWER PWM Fan Motor Assembly STARTER Starter Solenoid EBCM Electronic Brake Control Module Fuses Usage Passenger’s Side Taillamp RT PARK Assembly, Front Sidemarker and Front Parking Lamp Assembly HORN Dual Horn Assembly LT HI BEAM Driver’s Side High-Beam Headlamp LT LOW BEAM Driver’s Side Low-Beam Headlamp...
Page 398 Fuses SPARE Not Used SPARE Not Used Ignition Switch (Power to IGN-3 IGN SW and CRANK) VOLT CHECK ECM, TCM, IPC, ECM/TCM ® PASS-Key III+ Module WPR MOD Windshield Wiper Module Assembly POSTO2 Post O2 Sensors COMP CLUTCH Compressor Clutch WPR SW Windshield Wiper/Washer Switch FOG LAMP...
Page 399: Rear Underseat Fuse Block (Driver Side)
Rear Underseat Fuse Block (Driver Side) The driver’s side rear fuse block is located under the rear seat on the driver’s side of the vehicle. The carpet must be lifted up to access the rear fuse block. To access the fuse block, push in the two tabs located at each end of the fuse block cover.
Page 400 Fuses L FRT HTD Driver’s Heated Seat Module SEAT MOD MEM/ADAPT Driver’s Power Seat Switch, SEAT Memory Seat Module Universal Garage Door Opener, THEFT Intrusion Sensor, Diversity Antenna Module REVERSE ISRVM (Inside Rearview Mirror), LAMP License Plate Lamp Assembly SPARE Not Used POSITION Taillamp Assemblies,...
Page 401: (Passenger Side)
Rear Underseat Fuse Block (Passenger Side) The passenger’s side rear fuse block is located under the rear seat on the passenger’s side of the vehicle. The carpet must be lifted up to access the rear fuse block. To access the fuse block, push in the two tabs located at each end of the fuse block cover.
Page 402 Fuses INTERIOR Hush Panel Lamps, Puddle Lamps, LAMP Overhead Courtesy Lamp Assembly Passenger’s Door Module FRT DR MOD Rear Integration Module (RIM), Ignition Switch, Key Lock Cylinder REAR FOG Rear Fog Lamps (Export Only) LAMP SUSPNTN Suspension Module TV Tuner Assembly, Vehicle VICS/RAP Information Communication System (VICS) Module, Sunroof...
Page 403: Capacities And Speciﬁcations
Capacities and Speciﬁcations The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 6-12 for more information. Application Automatic Transmission Cooling System 3.6L V6 4.6L V8 Engine Oil with Filter 3.6L V6 4.6L V8 Fuel Tank Wheel Nut Torque...
Page 404 Engine 3.6L V6 (LY7) 4.6L V8 (LH2) 5-106 Engine Speciﬁcations VIN Code Transmission Automatic Automatic Spark Plug Gap 0.044 inches (1.1 mm) 0.040 inches (1.0 mm)
Page 405 Section 6 Maintenance Schedule ...6-2 Introduction ...6-2 Maintenance Requirements ...6-2 Your Vehicle and the Environment ...6-2 Using the Maintenance Schedule ...6-2 Scheduled Maintenance ...6-4 Additional Required Services ...6-6 Maintenance Footnotes ...6-7 Maintenance Schedule Owner Checks and Services ...6-9 At Each Fuel Fill ...6-9 At Least Once a Month ...6-9 At Least Once a Year ...6-10 Recommended Fluids and Lubricants ...6-12...
Page 406: Maintenance Schedule
Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Have you purchased the GM Protection Plan? The Plan supplements your new vehicle warranties. See your Warranty and Owner Assistance booklet or your dealer for details. Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts, and recommended ﬂuids and...
Page 407 Because of all the different ways people use their vehicles, maintenance needs vary. You may need more frequent checks and replacements. So please read the following and note how you drive. If you have any questions on how to keep your vehicle in good condition, ®...
Page 408: Scheduled Maintenance
The proper replacement parts, ﬂuids, and lubricants to use are listed in Recommended Fluids and Lubricants on page 6-12 and Normal Maintenance Replacement Parts on page 6-14. When your vehicle is serviced, make sure these are used. All parts should be replaced and all necessary repairs done before you or anyone else drives the vehicle.
Page 409 Scheduled Maintenance Service Maintenance I Maintenance II Change engine oil and ﬁlter. See Engine Oil on page 5-16. Reset oil life system. See Engine Oil Life System on page 5-22. An Emission Control Service. Lubricate chassis components. See footnote #. Visually check for any leaks or damage.
Page 410: Additional Required Services
Additional Required Services The following services should be performed at the ﬁrst maintenance service (I or II) after the indicated miles (kilometers) shown for each item. Service and Miles (Kilometers) Inspect fuel system for damage or leaks. Inspect exhaust system for loose or damaged components.
Page 411: Maintenance Footnotes
Service and Miles (Kilometers) Engine cooling system service (or every ﬁve years, whichever occurs ﬁrst). An Emission Control Service. See footnote (i). Inspect engine accessory drive belt. An Emission Control Service. See footnote (l). Maintenance Footnotes # Lubricate the front suspension, ball joints, steering linkage, transmission shift linkage, and parking brake cable guides.
Page 412 (d) Visually inspect wiper blades for wear or cracking. Replace wiper blades that appear worn or damaged or that streak or miss areas of the windshield. (e) Make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors, and anchorages are working properly.
Page 413: Owner Checks And Services
Owner Checks and Services These owner checks and services should be performed at the intervals speciﬁed to help ensure the safety, dependability and emission control performance of your ® vehicle. Your GM Goodwrench dealer can assist you with these checks and services. Be sure any necessary repairs are completed at once.
Page 414: At Least Once A Year
At Least Once a Year Starter Switch Check CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before you start, be sure you have enough room around the vehicle.
Page 415: Ignition Transmission Lock Check
Ignition Transmission Lock Check While parked, and with the parking brake set, try to turn the ignition to OFF in each shift lever position. • The ignition should turn to OFF only when the shift lever is in PARK (P). •...
Page 416: Recommended Fluids And Lubricants
Recommended Fluids and Lubricants Fluids and lubricants identiﬁed below by name, part number, or speciﬁcation may be obtained from your dealer. Usage Fluid/Lubricant Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certiﬁed for Gasoline Engines starburst symbol. Engine Oil GM Goodwrench (V6 Engine)
Page 417 Usage Fluid/Lubricant Windshield ® GM Optikleen Washer Solvent. Washer Power GM Power Steering Fluid Steering (GM Part No. U.S. 89021184, System in Canada 89021186). ® DEXRON -III Automatic Transmission Automatic Fluid. Look for “Approved for the Transmission H-Speciﬁcation” on the label. Multi-Purpose Lubricant, Superlube Key Lock (GM Part No.
Page 418: Normal Maintenance Replacement Parts
Normal Maintenance Replacement Parts Replacement parts identiﬁed below by name, part number, or speciﬁcation can be obtained from your dealer. Part Engine Air Cleaner/Filter Engine Oil Filter 3.6L V6 4.6L V8 Passenger Compartment Air Filter Element Spark Plugs 3.6L V6 4.6L V8 Windshield Wiper Blades (Hook Type) Driver’s Side –...
Page 419: Maintenance Record
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2. Any additional information from Owner Checks and Services on page 6-9 can be added on the following record pages. You should retain all maintenance receipts.
Page 420 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-16...
Page 421 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-17...
Page 422 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-18...
Page 423: Customer Assistance And Information
Section 7 Customer Assistance and Information ...7-2 Customer Satisfaction Procedure ...7-2 Online Owner Center ...7-4 Customer Assistance for Text Telephone (TTY) Users ...7-4 Customer Assistance Offices ...7-4 GM Mobility Reimbursement Program ...7-6 Roadside Service ...7-6 Courtesy Transportation ...7-8 Vehicle Data Collection and Event Data Recorders ...7-10 Collision Damage Repair ...7-11 Customer Assistance and Information...
Page 424: Customer Assistance And Information
Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Cadillac. Normally, any concerns with the sales transaction or the operation of your vehicle will be resolved by your dealer’s sales or service departments. Sometimes, however, despite the best intentions of all concerned, misunderstandings can occur.
Page 425 STEP THREE: Both General Motors and your dealer are committed to making sure you are completely satisﬁed with your new vehicle. However, if you continue to remain unsatisﬁed after following the procedure outlined in Steps One and Two, you should ﬁle with the BBB Auto Line Program to enforce any additional rights you may have.
Page 426: Online Owner Center
Telephone (TTY) Users To assist customers who are deaf, hard of hearing, or speech-impaired and who use Text Telephones (TTYs), Cadillac has TTY equipment available at its Customer Assistance Center. Any TTY user can communicate with Cadillac by dialing: 1-800-833-CMCC (2622).
Page 427 United States — Customer Assistance Cadillac Customer Assistance Center Cadillac Motor Car Division P.O. Box 33169 Detroit, MI 48232-5169 1-800-458-8006 1-800-833-2622 (For Text Telephone devices (TTYs)) Roadside Assistance: 1-800-882-1112 Fax Number: 313-381-0022 From Puerto Rico: 1-800-496-9992 (English) 1-800-496-9993 (Spanish) Fax Number: 313-381-0022 From U.S.
Page 428: Gm Mobility Reimbursement Program
This service is provided at no charge for any situation covered by the base warranty coverage and at a nominal charge if the Cadillac is no longer covered by the base warranty. Roadside Service is available only in the United States and Canada.
Page 429: Cadillac Owner Privileges
A dealer technician, if available, can travel to your location within a 30 mile (50 km) radius of a participating Cadillac dealership. If beyond this radius, we will arrange to have your car towed to the nearest Cadillac dealership.
Page 430: Courtesy Transportation
Courtesy Transportation To enhance your ownership experience, we and our participating dealers are proud to offer Courtesy Transportation, a customer support program for new vehicles. The Courtesy Transportation program is offered to customers in conjunction with the Bumper-to-Bumper coverage provided by the New Vehicle Limited Warranty. Several transportation options are available when warranty repairs are required.
Page 431: Additional Program Information
Courtesy Rental Vehicle Your dealer may arrange to provide you with a courtesy rental vehicle or reimburse you for a rental vehicle that you obtain if your vehicle is kept for a warranty repair. Reimbursement will be limited to a maximum amount per day and must be supported by receipts.
Page 432: Vehicle Data Collection And Event Data Recorders
Vehicle Data Collection and Event Data Recorders Your vehicle, like other modern motor vehicles, has a number of sophisticated computer systems that monitor and control several aspects of the vehicle’s performance. Your vehicle uses on-board vehicle computers to monitor emission control components to optimize fuel economy, to monitor conditions for airbag deployment and, if so equipped, to provide anti-lock braking and to help the driver control the...
Page 433: Collision Damage Repair
In addition, once GM collects or receives data, GM may: • use the data for GM research needs, • make it available for research where appropriate conﬁdentiality is to be maintained and need is shown, or • share summary data which is not tied to a speciﬁc vehicle with non-GM organizations for research purposes.
Page 434: Repair Facility
Repair Facility GM also recommends that you choose a collision repair facility that meets your needs before you ever need collision repairs. Your GM dealer may have a collision repair center with GM-trained technicians and state of the art equipment, or be able to recommend a collision repair center that has GM-trained technicians and comparable equipment.
Page 435 • Remove any valuables from your vehicle before it is towed away. Make sure this includes your insurance information and registration if you keep these items in your vehicle. • Gather the important information you will need from the other driver. Things like name, address, phone number, driver’s license number, vehicle license plate, vehicle make, model and model year, Vehicle Identiﬁcation Number (VIN), insurance company...
Page 436: Reporting Safety Defects
If another party’s insurance company is paying for the repairs, you are not obligated to accept a repair valuation based on that insurance company’s collision policy repair limits, as you have no contractual limits with that company. In such cases, you can have control of the repair and parts choices as long as cost stays within reasonable limits.
Page 437: Service Manuals
In addition to notifying NHTSA (or Transport Canada) in a situation like this, we certainly hope you will notify us. Please call us at 1-800-458-8006, or write: Cadillac Customer Assistance Center Cadillac Motor Car Division P.O. Box 33169 Detroit, MI 48232-5169 In Canada, please call us at 1-888-446-2000.
Page 438: Service Bulletins
Service Bulletins Service Bulletins give technical service information needed to knowledgeably service General Motors cars and trucks. Each bulletin contains instructions to assist in the diagnosis and service of your vehicle. In Canada, information pertaining to Product Service Bulletins can be obtained by contacting your General Motors dealer or by calling 1-800-GM-DRIVE (1-800-463-7483).
Page 439 Accessories and Modiﬁcations ... 5-3 Accessory Power Outlet(s) ... 3-23 Adding Equipment to Your Airbag-Equipped Vehicle ... 1-61 Additives, Fuel ... 5-6 Add-On Electrical Equipment ... 5-96 Adjustable Throttle and Brake Pedal ... 2-24 Air Cleaner/Filter, Engine ... 5-24 Air Conditioning ... 3-25 Airbag Readiness Light ...
Page 440 Audio System(s) (cont.) Radio with CD ... 3-82 Setting the Time ... 3-81 Theft-Deterrent Feature ... 3-111 Understanding Radio Reception ... 3-112 XM™ Satellite Radio Antenna System ... 3-114 Automatic Transmission Fluid ... 5-25 Operation ... 2-26 Battery ... 5-42 Exterior Lighting Battery Saver ...
Page 441 Child Restraints Child Restraint Systems ... 1-35 Infants and Young Children ... 1-31 Lower Anchors and Tethers for Children ... 1-39 Older Children ... 1-28 Securing a Child Restraint in a Rear Seat Position ... 1-45 Securing a Child Restraint in the Right Front Seat Position ...
Page 442 Customer Assistance Information (cont.) Reporting Safety Defects to the Canadian Government ... 7-14 Reporting Safety Defects to the United States Government ... 7-14 Roadside Service ... 7-6 Service Publications Ordering Information ... 7-15 Daytime Running Lamps ... 3-17 Defensive Driving ... 4-2 Delayed Locking ...
Page 443 Engine Air Cleaner/Filter ... 5-24 Battery ... 5-42 Check and Service Engine Soon Light ... 3-42 Coolant ... 5-26 Coolant Heater ... 2-25 Coolant Temperature Gage ... 3-41 Coolant Temperature Warning Light ... 3-40 Engine Compartment Overview ... 5-12 Exhaust ... 2-33 Oil ...
Page 444 Gage Engine Coolant Temperature ... 3-41 Fuel ... 3-47 Speedometer ... 3-35 Tachometer ... 3-36 Garage Door Opener ... 2-42 Gasoline Octane ... 5-5 Speciﬁcations ... 5-6 Glove Box ... 2-46 GM Mobility Reimbursement Program ... 7-6 Hazard Warning Flashers ... 3-6 Head Restraints ...
Page 445 Jump Starting ... 5-42 Keyless Entry System ... 2-4 Keys ... 2-3 Labelling, Tire Sidewall ... 5-54 Lamps Exterior Lighting Battery Saver ... 3-19 Fog ... 3-18 Reading ... 3-20 LATCH System Child Restraints ... 1-39 Level Control ... 4-51 Liftgate, Power ...
Page 446 Locks (cont.) Power Door ... 2-9 Programmable Automatic Door Locks ... 2-10 Rear Door Security Locks ... 2-10 Loss of Control ... 4-16 Luggage Carrier ... 2-47 Lumbar Power Controls ... 1-3 Magnetic Ride Control ... 4-10 Maintenance Schedule Additional Required Services ... 6-6 At Each Fuel Fill ...
Page 447 Odometer ... 3-35 Odometers, Trip ... 3-35 Off-Road Driving ... 4-17 Off-Road Recovery ... 4-14 Engine ... 5-16 Pressure Light ... 3-45 Oil, Engine Oil Life System ... 5-22 Older Children, Restraints ... 1-28 Online Owner Center ... 7-4 ® ®...
Page 448 Questions and Answers About Safety Belts ... 1-15 Radios ... 3-80 Care of Your CD and DVD Player ... 3-113 Care of Your CDs and DVDs ... 3-113 Navigation/Radio System, see Navigation Manual ... 3-98 Radio with CD ... 3-82 Setting the Time ...
Page 449 Safety Belt Pretensioners ... 1-28 Reminder Light ... 3-36 Safety Belts Care of ... 5-90 Driver Position ... 1-16 How to Wear Safety Belts Properly ... 1-16 Questions and Answers About Safety Belts ... 1-15 Rear Safety Belt Comfort Guides ... 1-26 Rear Seat Passengers ...
Page 450 Spare Tire (cont.) Removing ... 5-74 Storing ... 5-83 Speciﬁcations, Capacities ... 5-105 Speedometer ... 3-35 Sport Mode Light ... 3-45 ® StabiliTrak System ... 4-11 Starting Your Engine ... 2-24 Status of Vehicle Systems, DIC ... 3-49 Steering ... 4-12 Steering Wheel Controls, Audio ...
Page 451 Tires (cont.) Pressure Monitor System ... 5-62 Removing the Flat Tire ... 5-76 Removing the Spare Tire and Tools ... 5-74 Secondary Latch System ... 5-81 Storing a Flat or Spare Tire and Tools ... 5-83 Tire Sidewall Labelling ... 5-54 Tire Terminology and Deﬁnitions ...
Page 452 Warning Lights, Gages and Indicators ... 3-33 Warnings DIC Warnings and Messages ... 3-57 Hazard Warning Flashers ... 3-6 Other Warning Devices ... 3-6 Safety and Symbols ... iii Vehicle Damage ... iv Wheels Alignment and Tire Balance ... 5-70 Different Size ...

This manual is also suitable for:

Srx

Cadillac 2006 SRX Owner's Manual

Section 1 Seats and Restraint Systems

Front Seats

Rear Seats

Safety Belts

Child Restraints

Airbag System

Restraint System Check

Section 2 Features and Controls

Features and Controls

Keys

Doors and Locks

Windows

Theft-Deterrent Systems

Starting and Operating Your Vehicle

Mirrors

Onstar System

Universal Home Remote System

Storage Areas

Sunroof

Vehicle Personalization

Section 3 Instrument Panel

Instrument Panel Overview

Climate Controls

Warning Lights, Gages, and Indicators

Driver Information Center (DIC)

Audio System(S)

Section 4 Driving Your Vehicle

Your Driving, the Road, and Your Vehicle

Towing

Quick Links

Chapters

Related Manuals for Cadillac 2006 SRX

Summary of Contents for Cadillac 2006 SRX