Summary of Contents for Gtech CCD001
- Page 1 Cordless Combi Drill CCD001 Model number: OPERATING MANUAL 4614_Drill_manual_aw.indd 1 4614_Drill_manual_aw.indd 1 28/10/2020 16:33 28/10/2020 16:33...
-
Page 2: Important Safeguards
IMPORTANT SAFEGUARDS: IMPORTANT: To avoid serious personal injury, do not attempt to use this product until you read the manual thoroughly and understand it complete- ly. Save this manual and review frequently for safe operation and instruct- ing others who may use this tool. Keep this manual for the safety warnings, precautions, operations, inspections and maintenance information. -
Page 3: Electrical Safety
Electrical safety: binding, making it easier to use. • Do not use the tool for anything other • The charger’s power plug must match than its intended use. the outlet. Never modify the plug or try • Do not use the tool if the trigger does to plug the tool into an outlet that does not actuate properly. -
Page 4: Tool Service
liquid flush with water and seek medical help. Battery liquid can cause irritation or burns. • Do not store batteries in areas that can reach or exceed 105°F. (Such as outside sheds or metal buildings in the summer). • Only charge the battery with a charger recommended by the manufacturer. -
Page 5: About Your Product
Thank you for choosing Gtech “Welcome to the Gtech family. I started Gtech to create sensible, easy to use products that do a great job, and hope you get many years of troublefree performance from your new product.” Nick Grey –... -
Page 6: Installing And Removing The Battery
Installing and removing the battery To install, simply insert the battery pack. Make sure the latch on the battery snaps in place and battery pack is secured to the tool. To remove, depress the latch..and pull out the battery pack. 4614_Drill_manual_aw.indd 6 4614_Drill_manual_aw.indd 6 28/10/2020 16:33... -
Page 7: Variable Speed Trigger
Variable speed trigger Forward/reverse switch The variable speed trigger (6) delivers higher Set the forward/reverse switch (9) in the OFF speed with increased trigger pressure and (Centre lock) position to lock the trigger and lower speed with decreased trigger pressure. help prevent accidental starting when not in To turn on the tool, depress the trigger. -
Page 8: Speed Selector
Installing and removing drill bit Turn the chuck sleeve (4) counterclockwise (as To remove the bit, turn the chuck sleeve viewed from the front) to open the chuck jaws. clockwise to release. Place the driver/ drill bit into the chuck as far Caution: Do not touch a drill bit just after as it goes. -
Page 9: Mode Selector
Mode selector Drilling mode (rotation only, torque adjustment not active) Hammer drilling mode (rotation with hammering, torque adjustment not active) Screw driving mode (rotation with clutch, torque adjustment active) The tool is equipped with three modes for different applications. Turn the mode selector ring (2) to select the desired mode. -
Page 10: Charging The Battery
Charging the battery To charge the battery, line up the slot of the The battery indicator light should turn from battery with the slot of the charger and slide green to red when the battery is charging. into place. The charger is sold separately. When the indicator light has turned green the battery should be fully charged. -
Page 11: Attaching The Belt Clip
Attaching the belt clip The belt clip (8) may be installed on either side To install, insert the clip into the groove in the of the tool. housing and fasten it with screw. To remove, simple remove the screw and then remove the belt clip. -
Page 12: Maintenance
Maintenance Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and maybe damaged by their use. Use clean cloth to remove dirt, dust, oil, grease, etc. WARNING: Remove the battery from the tool for any inspection, maintenance, and cleaning. Troubleshooting The product isn’t working The battery may have cut out due to... -
Page 13: Product Support
If these initial tips do not solve your problem we please visit our support area where you can find troubleshooting help including online manuals, FAQs and howtovideos, as well as genuine spares and replacement parts compatible with your product. Visit: www.gtech.co.uk/support Online Live chat support support@gtech.co.uk... -
Page 14: Warranty Registration
If your product is within its warranty and has a fault that cannot be resolved from the troubleshooting section or online support, please do the following: • Contact our Gtech Customer Care Helpline on UK: 08000 308 794, who will go through any troubleshooting with you to identify the fault. - Page 15 symbol indicates that this product is Call your local council, civic amenity site, or recy- covered by legislation for waste electrical and cling centre for information on the disposal and electronic products (2012/19/EU) recycling of electrical products. Alternatively visit www.recycle-more.co.uk for advice on recycling When the product has reached the end of its life, it and and to find your nearest recycling facilities.
- Page 16 Notes 4614_Drill_manual_aw.indd 16 4614_Drill_manual_aw.indd 16 28/10/2020 16:33 28/10/2020 16:33...
- Page 17 Notes 4614_Drill_manual_aw.indd 17 4614_Drill_manual_aw.indd 17 28/10/2020 16:33 28/10/2020 16:33...
- Page 18 Grey Technology Limited Brindley Road, Warndon, Worcester WR4 9FB email: support@gtech.co.uk telephone: 08000 308 794 www.gtech.co.uk 4614_Drill_manual_aw.indd 18 4614_Drill_manual_aw.indd 18 28/10/2020 16:33 28/10/2020 16:33...
Need help?
Do you have a question about the CCD001 and is the answer not in the manual?
Questions and answers