Do you have a question about the SKIPPER and is the answer not in the manual?
Questions and answers
Corinne Rieusset
June 2, 2025
Mon robot ne fait pas sont travail
2 comments:
Corinne Rieusset
June 2, 2025
@Corinne Rieusset Je ne sait pas programer mon robot il fait n'importe quoi il se relève au fond de la piscine et il n ettoi pas bien le fond
Mr. Anderson
June 2, 2025
The YZAKI SKIPPER robot may not be functioning properly for several reasons:
1. Battery Issues: - If the battery is very low or damaged, the robot may not work. A flashing red light indicates a very low or faulty battery. - Overcharging (more than 8 hours) or long periods without charging can damage the battery.
2. Startup Procedure Not Followed: - The robot must be placed horizontally in water and all trapped air must be released for proper operation.
3. Incorrect Charging Environment: - Charging near fire or high heat can damage the robot.
4. Improper Use or Physical Damage: - Piercing, hitting, or dropping the robot can cause malfunction.
5. Filter Issues: - Dirty or improperly installed filters can affect operation.
6. Incorrect Bluetooth Setup: - If using the app, incorrect configuration may prevent proper function.
7. Low Water Temperature: - The robot operates only in water temperatures between 10℃ and 35℃.
Checking these factors can help identify the cause of the malfunction.
This answer is automatically generated
Vanessa
May 24, 2025
Je cherche un Switch button pour Mon Yzaki Skipper.
1 comments:
Mr. Anderson
May 25, 2025
The switch button for the YZAKI Skipper is located on the cleaner itself. It is used to power the cleaner on or off and to set up the Bluetooth application.
This answer is automatically generated
Summary of Contents for YZAKI SKIPPER
Page 1
ROBOT DE PISCINE AUTONOME ROBOTIC POOL CLEANER SKIPPER MANUEL D’UTILISATION USER MANUAL...
Page 2
Précautions importantes : 1. Il est interdit d’utiliser le robot dans les conditions inappropriées. Veuillez lire attentivement la notice avant utilisation. Aucune responsabilité du fabricant ne pourra être engagée en cas de mauvaise utilisation. 2. Il faut utiliser uniquement les pièces de rechange fournies par le fabricant. 3.
Page 3
15. Le couvercle d’étanchéité du moteur contient la graisse lubrifiante. Si jamais il y a du débordement de la graisse, l’eau est susceptible d’être très légèrement contaminée. 16. Chargez la batterie à une température ambiante comprise entre 10°C et 35°C. Avant de charger une batterie chaude, laissez-la refroidir d’abord.
Page 4
Attention ! 1. Présenter le robot horizontalement face à l’eau, démarrer le robot et le mettre dans l’eau pour qu’il tombe lentement au fond de la piscine. Le robot va commencer à travailler pendant environ 20 secondes arpès le démarrage. ( Pour un fonctionnement correct du robot, il faut évacuer tout l’air emprisonné).
1. Introduction Le robot nettoyeur rechargeable SKIPPER est un équipement de nettoyage automatique pour les piscines. Il peut nettoyer la piscine automatiquement en filtrant l'eau du bassin. Ce robot est alimenté par batterie lithium 12.6V 8.8AH donc très fiable. Veuillez lire attentivement le présent mode d’emploi avant d’utiliser ce robot afin de pouvoir utiliser le robot correctement.
4. Manuel opératoire 4.1 Bouton et voyant Voyant Statut Interrupteur Description Fonction Basculer vers le haut pour mettre en route ( voyant bleu). Pour la connexion et la configuration de l’Application via Bluetooth, basculer vers le bas et puis vers le haut dans 5 secondes après le Intérrupteur démarrage du robot ( voyant violet).
4.2 Chargement du robot 4.2.1 Sortir du robot de l’eau S’assurer que le robot est arrêteé(indicateur de statut est complètement éteint. Sortir le robot de l’eau, le charge à l’intérieur ou à l’abri de l’aspersion d’eau. La lumière rouge de l’indicateur du chargeur signifie que le robot est en charge et elle devient verte si le chargement est accomplie.
Page 10
4.3.2 Rincer et nettoyer les filtres (4-5) 4.3.3 Réinstaller les filtres. Aligner le filtre avec la ouverture d’évacuation d’eau et remettre les filtres dans le robot avant de fermer le capot. 5. Appilcation via Bluetooth...
5.1 Installer Application Nom de l’application : WYRobot Adresse de téléchargement : Chercher le nom d’application sur Apple store pour iPhone,et Google play pour smartphone Android. Autoriser l’accès de permission Bluetooth et permission localisation pour que le robot soit trouvé via Bluetooth. Pour Android 10 ou la version supérieure, le service de localisation doit aussi êtes activé.
7. Garantie 1. La période de garantie est de 24 mois à partir de la date d'achat.Seuls le moteur et la carte électronique sont couverts par la garantie. Les autres pièces ne sont pas couvertes par la garantie et constituent des pièces d’usure. 2.
Important Precaution Please read through the entire manual before using your new robotic pool cleaner. We are not held liable for any loss or injury caused by improper use. Failure to comply with the following cautions could cause damage to pool cleaner or personal loss and injury.
Page 14
19. Do not strike the cleaner with sharp objects. 20. Do not charge or use or store the cleaner near hot source or extremely high temperature.
Page 15
Contents Important Precaution ........................13 Attention ............................16 1. Brief Introduction ........................17 2. security ............................17 3. General Specification ........................ 18 4. Operation ............................ 19 4.1 Switch button and indicator ..................19 4.2 How to charge ......................20 4.3 Filter cleaning....................... 21 5.
Attention 1. Put into the pool with the cleaner bottom towards the wall. Hold the top handle and switch on the cleaner. The cleaner will start working after 20 seconds when emptying trapped air inside (make sure to empty the inside air in order to make the robot work well), then the cleaner can immerse into the pool floor.
1. Brief Introduction The robotic pool cleaner SKIPPER is a new type of highly efficient and energy-saving swimming pool cleaning robot. It cleans the pool walls and bottom automatically without replacing the pool water. It is totally environmental-friendly. For safe operation, the cleaner is powered by a rechargeable lithium battery (12.6V, 8.8Ah).
3. General Specification Rated input voltage of charger 100VAC-240VAC Capacity 8.8AH 47-63 Hz Rated input frequency of charger Power Max. charging voltage 12.6VAC Charging current 1.8A Running time max. 90min Flow rate max. 10m³/h (appr. 2642gal/h) 180μm Filter density Running speed max.
4. Operation ② Indicator ① Switch button 4.1 Switch button and indicator Item Function Description Push the button upwards to power on the cleaner(blue indicator); Push the button downwards and then upwards in 5 seconds after power on to connect and set ①...
4.2 How to charge 4.2.1 Remove the cleaner from the pool ① Switch off (No indictor flashes) the cleaner ② Charge the cleaner indoor and at least 3m (appr. 10ft) from the edge of the pool for charging. ③ Red light indicates the battery is being charged. ④...
4.3 Filter cleaning 4.3.1 Open the top cover: Put the robot aside the pool and open the top cover (Figure 4-1), the filter basket is located as show in Figure 4-2. Figure 4-1 Figure 4-2 4.3.2 Take out the filter basket (Figure 4-3) Figure 4-3 4.3.3 Wash filter basket (Figure 4-4) 4.3.4 Re-install the filter basket in reverse steps...
5. Bluetooth Application instructions 5.1 Install Application Application name: WYRobot Download address: Search application name in Apple store for iPhone, and Google play for Android smartphones. Authorize access of Bluetooth permissions and location permissions, otherwise nearby cleaners cannot be searched. For Android 10 or above version, location service also needs to be turned on.
7. Warranty This product has passed all quality control and safety tests, conducted by the technical department of the manufacturer. Warranty information: 1. The warranty is covered for 24 months for motors and PCB, from the date of its original purchase.
Need help?
Do you have a question about the SKIPPER and is the answer not in the manual?
Questions and answers
Mon robot ne fait pas sont travail
@Corinne Rieusset Je ne sait pas programer mon robot il fait n'importe quoi il se relève au fond de la piscine et il n ettoi pas bien le fond
The YZAKI SKIPPER robot may not be functioning properly for several reasons:
1. Battery Issues:
- If the battery is very low or damaged, the robot may not work. A flashing red light indicates a very low or faulty battery.
- Overcharging (more than 8 hours) or long periods without charging can damage the battery.
2. Startup Procedure Not Followed:
- The robot must be placed horizontally in water and all trapped air must be released for proper operation.
3. Incorrect Charging Environment:
- Charging near fire or high heat can damage the robot.
4. Improper Use or Physical Damage:
- Piercing, hitting, or dropping the robot can cause malfunction.
5. Filter Issues:
- Dirty or improperly installed filters can affect operation.
6. Incorrect Bluetooth Setup:
- If using the app, incorrect configuration may prevent proper function.
7. Low Water Temperature:
- The robot operates only in water temperatures between 10℃ and 35℃.
Checking these factors can help identify the cause of the malfunction.
This answer is automatically generated
Je cherche un Switch button pour Mon Yzaki Skipper.
The switch button for the YZAKI Skipper is located on the cleaner itself. It is used to power the cleaner on or off and to set up the Bluetooth application.
This answer is automatically generated