Cerio POE-ISP User Manual

POE-ISP
Gigabit Ethernet PoE Pass-through Surge Protector
User's Guide
FCC Certifications
This Equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received; including
interference that may cause undesired operation.
CE Mark Warning
This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022 class A for ITE,
the essential protection requirement of Council Directive 89/336/EEC on the approximation of the laws of the
Member States relating to electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may be possible that information in this document
is not up-to-date. Please check with your local distributors for the latest information. No part of this document can be
copied or reproduced in any form without written consent from the company.
Trademarks:
All trade names and trademarks are the properties of their respective companies.
Copyright © 2016, All Rights Reserved.
Unpacking Information
Thank you for purchasing our PoE series products. Before installation,
please check that your package contains the following items.
Open the shipping cartons of the unit and carefully unpack its
contents. The carton should contain the following items:
1. POE-ISP Main Unit x 1
2. Warranty Card x 1
3. 18AWG grounding cable x 1
4. Wall mounting screw set x 1
5. Quick Installation Guide x 1
Hardware Overview
Introduction
The CERIO POE-ISP is a PoE Pass-through Ethernet Surge Protector
provides superior lightening and surge protection over gigabit
networks speeds to provide Gigabit Power-over-Ethernet (PoE) over
a single Ethernet cable. It provides durable design featuring a higher
surge capability and lower clamping voltage. And the 10 kA Impulse
Discharge Current guarantees reliable surge protection. The
advantage of POE-ISP surge protector design is the added level of
protection due to its large power rating and fast discharge time.
Highlight Features
Complying with IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX,

IEEE 802.3ab 1000Base-T standards.
Supports 10/100/1000Mbps Gigabit Ethernet and provides

Gigabit transfer speed and Power over Ethernet (PoE) pass
through.
Load current self-protection mechanism and grounding wire

function pulse discharge current protection design
Built in grounding pad which can connect to grounding cable to

lower clamping voltage for better and more reliable protection
and supports 10 kA Impulse Discharge Current.
Supports 2 protection mode : Line-to-Ground and Line-to-Line.

Protects all Eight (8) pins of the Ethernet cable.

Plug and Play, no software required.

Supports desktop, multiple units combination and wall

mounting easy to use.
Product Specifications
Standards & Hardware Specifications
Standard
Network Media
Data Transfer Rate
Clamping Line-to-Ground
Clamping Line-to-Line
Data In
Ethernet Connector
Surge Protection Design
Environmental & Mechanical Characteristic
PoE Operation Voltage
PoE Operation Current
PoE Power Load
PoE Input Voltage
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
Dimension ( W x D x H )
Weight ( g )
Case of material
Production Location
Supports
IEEE802.3 10BASE-T
IEEE802.3u 100BASE-TX
IEEE802.3ab1000BASE-T
10BASE –T: UTP Cat. 3 or up
100BASE-TX : UTP Cat. 5 or up
1000BASE-T: UTP Cat. 5 or up
10/100/1000Mbps (Half-duplex)
20/200/2000Mbps (Full-duplex)
Common mode up to 10 kA
Differential mode up to 1 kA
Connects PC/HUB/Switch
RJ-45 x1 for Line in
RJ-45 x1 for Line out
10KV (After grounding ability)
57 VDC (Max)
Two pair: 0.65A(Max) ,Four pair:
1.3A(Max)
74Watt (Four Pair Max)
44~57V
-10° to 60° C
-20° to 65° C
5% to 90% non-condensing
5% to 90% non-condensing
84.5 x 80 x 39.5mm
96.2g
ABS
TW Only
IEC/EN 61643-21 (Safety) compatible
IEC/EN 61000-4-5 (EMC) compatible
RoHS compatible
V1.5