Advertisement
1.3.5. Regularly inspect power supply cables and plugs for wear or damage and check all connections to
ensure none is loose.
1.3.6. Important: Ensure that the voltage marked on the appliance matches the power supply to be used
and that the plug adaptor is fitted with the recommended fuse - 5A.
1.3.7. DO NOT pull the plug from the socket by the cable.
1.3.8. DO NOT use worn or damage cables, plugs or connectors. Immediately have any faulty item repaired
or replaced by a qualified electrician.
Note that the earth pin 'E' remains unconnected.
1.3.9. If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is
preferred since any appliance plugged into it will be protected. The cable core section is important and
should be at least 1.5mm², but to be absolutely sure that the capacity of the reel is suitable for this product
and for others which may be used in the other output sockets, we recommend the use of 2.5mm² section
cable. If extension reel is to be used outdoors, ensure it is marked for outdoor use.
1.4.
BATTERY ChARGER SAFETY INSTRUCTIONS
WARNING! DO NOT attempt to charge any battery other than that supplied for the wrench. Other types
of batteries may explode!
All mains electrical supply safety features must be followed as described in 1.3 above.
Disconnect the charger from the mains supply when not in use.
DO NOT charge battery if room temperature is below 10°C (50°F) or above 40°C (104°F).
DO NOT expose the charger to damp or wet conditions.
DO NOT pull or carry the charger by the power lead.
DO NOT operate the charger if it has been dropped, or has received a sharp knock, or is damaged. Take the charger to an authorised
agent for repair or obtain a replacement.
DO NOT dismantle the charger as this may cause damage and/or personal injury and will invalidate the warranty.
DO NOT insert foreign objects or material into the hole reserved for the battery pack.
DO NOT recharge a second battery pack immediately after charging the first. Consecutive charging will overheat the charger.
Allow the unit to cool for 15 minutes before charging the next pack.
Store the charger in the same manner as the battery pack in 1.2.
2.
INTRODUCTION & SPECIFICATION
Powerful, compact, cordless impact wrench with forward, reverse and variable speed
trigger control. Produces in excess of 386nm (285lb.ft) of torque - enough to remove
wheel nuts. Balanced tool with detachable side handle, vibration reducing grip and
aluminium alloy impact housing. Supplied with two 19.2Volt ni-Cad battery packs and
1 hour mains charger.
no-load Speed:. . . . . . . . . . . . . . . . . . . . 1600rpm
Impact Rate: . . . . . . . . . . . . . . . . . . . . . 2200bpm
Maximum Torque: . . . . . . . . . . . .285lb.ft / 386nm
Drive Size: . . . . . . . . . . . . . . . . . . . . . . . . . . .½"Sq
Weight:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.1kg
noise Power: . . . . . . . . . . . . . . . . . . . . . . .
noise Pressure: . . . . . . . . . . . . . . . . . . . . .
Battery Pack: . . . . . . . . . . . Model no: CP1950BP
3. OPERATING INSTRUCTIONS
Note: When new, the battery pack will have been shipped in a low charge state.
It will take longer to charge initially, and several subsequent charges may also
take a little longer than when the battery pack reaches its optimum performance.
3.1.
BS ADAPTOR
3.1.1. The battery charger is supplied with a European standard Schuko plug.
To use the battery charger in the UK the BS Adaptor must be used.
3.1.2
open up the adaptor and insert the Schuko plug (fig.1). Ensure its fully inserted into the connectors.
3.1.3
Close the adaptor around the plug, to secure the adaptor to the plug tighten the
screw in the middle of the adaptor.
3.2.
ChARGING ThE BATTERY PACK
3.2.1. Remove the battery pack (fig.2.4) from the wrench, by depressing the two side
release clips (fig.2.5).
WARNING! Do not touch metal terminals.
3.2.2. Place wrench in carry case and remove the battery charger.
3.2.3. The battery pack and charger have the positive (+) and negative (-) terminals
marked. Align the correct terminals and insert the battery into slot (fig.3).
Note: The battery pack is designed so that it will only enter the charger
unit the correct way.
When placed in the charger, a very slight downward pressure will seat the pack
firmly into the power terminals.
3.2.4. Switch on mains supply to charger, after 3 seconds the charging will automatically
commence and the red lED will illuminate and the green lED will flash.
3.2.5. When the fast charge is complete the red lED will go out and the green lED
will be constant to indicate the battery pack is fully charged and now ready for use.
Note: The charge time is approximately 1 hour (after the initial charges).
3.2.6. After removing the battery, disconnect the charger from the mains supply and
store in the carry case.
Note: Refer to the 'Charging Guide' (fig.3) on the charger for quick reference on the state
of the battery and charger.
WARNING! If the red lED is flashing and the green lED is off, this indicates the
battery needs to be inspected for fault.
WARNING! If the red and green lED are flashing the battery and charger are overheating.
88dB.A
99dB.A
Original Language Version
fig.1
fig.2
fig.3
CP1950
Issue: 1 - 28/07/11
Advertisement
