1. Manuals
  2. Brands
  3. Sure Heat Manuals
  4. Patio Heater
  5. Four Seasons FS87PHLP
  6. Use and care manual

Sure Heat Four Seasons FS87PHLP Use And Care Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
The store where you made the purchase does not stock
parts for this item. If you need parts, whether they are
missing or damaged, please call Customer Service at
Call us between 8:00 AM and 5:00 PM Eastern time, Monday through Friday
USE AND CARE MANUAL
For Model FS87PHLP
or email us at saleshelp@sureheat.com
Stop! Missing a part? DO
NOT RETURN PRODUCT
TO STORE
FOR YOUR SAFETY:
1. Read this Manual before
attempting to assemble or
operate your patio heater.
2. Follow safety instructions.
3. Check for leaks according
to the directions in this
Manual before operating
your patio heater, even if
purchasing an assembled
patio heater.
4. Keep this Manual for
future reference.
5. Contact 1-800-229-5647
should you need assembly
assistance or have any
questions.
1-800-229-5647

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Four Seasons FS87PHLP and is the answer not in the manual?

Questions and answers

Related Manuals for Sure Heat Four Seasons FS87PHLP

Summary of Contents for Sure Heat Four Seasons FS87PHLP

  • Page 1 USE AND CARE MANUAL For Model FS87PHLP Stop! Missing a part? DO NOT RETURN PRODUCT TO STORE FOR YOUR SAFETY: 1. Read this Manual before attempting to assemble or operate your patio heater. 2. Follow safety instructions. 3. Check for leaks according to the directions in this Manual before operating your patio heater, even if...

  • Page 2: Table Of Contents

    Table of Contents General Safety Instructions................Components & Hardware.................. Additional Requirements.................. Assembly Process Step 1 – Attach Wheel Assembly to Base............Step 2 – Attach Bucket to Base................ Step 3 – Attach Support Brackets to Base............Step 4 – Attach Post to Support Brackets............Step 5 –...

  • Page 3: General Safety Instructions

    General Safety Instructions IMPORTANT SAFETY INFORMATION This manual contains important information about the assembly, operation and maintenance of this patio heater. General safety information is presented in these fi rst few pages and is also located throughout the manual. - Keep this manual for future reference and to educate new users of this product. This manual should be read in conjunction with the labeling on the product.
  • Page 4 General Safety Instructions ▲ ▲ DANGER DANGER D A N G E R i n d i c a t e s y o u c a n b e k i l l e d o r seriously injured if you don't immediately follow EXPLOSION - FIRE HAZARD instructions.
  • Page 5 General Safety Instructions ▲ DANGER ▲ DANGER CARBON MONOXIDE HAZARD EXPLOSION - FIRE HAZARD - This heater is a combustion appliance. All - Never store propane near high heat, open flames, combustion appliances produce carbon monoxide pilot lights, direct sunlight, other ignition souces or (CO) during the combustion process.

  • Page 6: Components & Hardware

    Components & Hardware Reflector Panel (3) Reflector Plate Reflector Assembly Reflector Stud (3) Heater Burner Screen Heater Assembly Cylinder Housing Post Gas Hoseless Regulator Regulator Base Wheel...

  • Page 7: Additional Requirements

    Components & Hardware Hardware Used in Step(s) Picture Description Small Bolt Small Flat Washer Small Screw Large Flat Total 9 6 & 9 Washer M e d i u m F l a t Washer Cap Nut Small screw Wing Nut Reflector Stud 1 / 3 / 4 / Wrench...

  • Page 8: Assembly Process

    Assembly Process Step 1 - Attach Wheel Assembly to Base Wheel Assembly 2 Medium bolts /2 Large Flange Nuts Line up holes in Wheel Bracket with corresponding holes in base. Insert 2 Medium bolts through holes and finger tighten the 2 Large Flange Nuts. Be sure that the Wheel Assembly is parallel to the base, and fully tighten bolts.

  • Page 9: Step 3 - Attach Support Brackets To Base

    Assembly Process Step 3- Attach Cylinder Housing to Base Attach Cylinder Housing loosely to Base with four Small Screws. Step 4- Attach Post to Cylinder Housing top Open the door, put post through the hole on the top of Cylinder Housing. Attach post to Cylinder Housing using four Small Bolts, Nuts and Small Flat Washers.

  • Page 10: Step 5 - Attach Reflection Studs To Screen Cover

    Assembly Process Step 5 - Attach Reflector Studs to Screen Cover Insert 3 Reflector Studs & 3 large Flat Washers. Tighten studs securely. 3 Reflector Studs 3 Large Flat Washers Step 6 - Attach Head Assembly to Post Remove 4 small bolts from the top of the Head 4 Small Bolts Head Assembly Assembly .

  • Page 11: Step 7 - Install Reflector

    Assembly Process Step 7 - Install Reflector ▲ WARNING Remove protective film before assembly Note: It is necessary for proper alignment of reflector section to loosely install all of the screws for assembly prior to tightening. Once all of the screws have been loosely installed, tighten with a wrench.
  • Page 12 Assembly Process Slide one Small Flat Washer over threaded end of screw and loosely screw on Cap Nut. Repeat procedure to complete the assembly of all three Reflector Panel sections. Slide Reflector Plate onto Reflector Panels. Slide one small Flat Washer over threaded end Insert one Small Screw.

  • Page 13: Step 8 - Attach Reflector Assembly To Studs

    Assembly Process Step 8 - Attach Reflector Assembly to Studs Support Heater. Slide 3 Large Flat Washers over threaded end of Studs. 6 Large Flat Washers 3 Wing Nuts Install Reflector Assembly onto three (3) studs. Install large flat washers on studs and securely tighten wing nuts. Make sure not to overtighten the wing nuts.

  • Page 14: Step 9 - Connect Hose & Regulator To Cylinder

    Assembly Process Step 9 - Connect Hose & Regulator to Cylinder Specifications - You must provide propane gas and propane cylinder. Use a standard 20 lb. Propane cylinder only. - Use this heater only with a propane vapor withdrawal supply system.

  • Page 15: Gas Requirement

    Gas Requirements L.P. GAS INSTALLATION Gas Heaters that are set to operate with L.P. gas come with a high capacity hose and regulator assembly. (Note: Only use the pressure regulator and hose assembly supplied with the heater or a replacement pressure regulator and hose assemblies ).

  • Page 16: Pre-Operation Leak Testing

    Pre-Operation Leak Testing GENERAL INFORMATION Although all gas connections on the heater are leak tested prior to shipment, a complete gas tightness check must be performed at the installation site due to possible shifting during shipment, installation or excessive pressure unknowingly being applied to the unit. Periodically check the whole system for leaks and immediately check the system if the smell of gas is detected.

  • Page 17: Operation

    Operation Do not attempt to "Light" the Heater if the odor of gas present!! BEFORE TURNING GAS SUPPLY ON: 1. Your heater was designed and approved for outdoor use only. DO NOT use it inside a building, garage, or any other enclosed area. 2.
  • Page 18 Operation If for some reason your igniter fails to deliver a spark, your heater can be started by inserting a lit match through the pilot view hole while pushing the control knob in while in the PILOT position. NOTE: If pilot fails to remain lit, all valves should be closed and wait at least 5 minutes before attempting to light.

  • Page 19: Care & Maintenance

    Care and Maintenance To enjoy years of outstanding performance from your heater, make sure you perform the following maintenance activities on a regular basis: Keep exterior surface clean. Use warm soapy water for cleaning. Never use flammable or corrosive cleaning agents. While cleaning your unit, be sure to keep the area around the burner and pilot assembly dry at all times.

  • Page 20: Troubleshooting

    Troubleshooting BEFORE CALLING CUSTOMER SERVICE If the heater does not function properly, use the following checklist. If the problem is: And this condition exists: Then do this: Cylinder valve is closed Open valve Blockage in orifice or pilot tube Clean or replace orifice or pilot tube Pilot won't light Air in gas line Open gas line and bleed it (pressing...

  • Page 21: Warranty

    Sure Heat Mfg warrants that the components of this appliance are warranted free from defects in material and workmanship for one year from the date of purchase. Sure Heat Mfg. at its option, will repair or replace this product or any component of the product found to be defective during the warranty period.

Table of Contents