Galaxy Audio AS-900T Quick Start Manual

GAL A X Y AUDIO
Wireless Personal Monitor
Included Components
1. 1.
AS-900T x1
2. AS-900R x1
3.
EB4 Ear Buds x1
4. MREWD Rack Kit x1
3.
5.
Antenna x1
6. Power Supply x1
7.
Quick Start Guide x1
5.
Setup
1
Insert the 5.5mm plug into the DC input
jack, plug the wall wart into a 120VAC
outlet.
Dual Rack Mounting
(Optional)
1
Screw one short rack ear on the left side
of the first transmitter, and one coupler
half onto the right side of the same
transmitter using the provided screws.
2
Insert Two AA Alkaline Batteries into the
Receiver.
2. 7.
4.
6.
2
Input Connection (XLR): Connect a
shielded XLR microphone cable to the
transmitter's left and right XLR input,
connect the other end into your signal
source's left and right outputs.
2
Screw one short rack ear on the right
side of the second transmitter, and one
coupler half onto the left side of the
same transmitter.
3
Turn the Level knob clockwise to power
on the Receiver.
Optional Accessories
1.
GAL A X Y AUDIO EB6 Ear Bud Upgrade
Q uick Start Guide
Wireless Personal Monitor AS-900
Included Components Optional Accessories What May be Needed
1. AS-900T x1 1. 2. 7. 1. EB6 Ear Bud Upgrade 1. 2. to Rack
2. AS-900R x1 2. EB10 Ear Bud Upgrade (Not Included)
3. EB4 Ear Buds x1 3.
Unlimited Receivers 1. Rack Screws 10/32 x .75",
4. MREWD Rack Kit x1 can be added 3. Phillips Truss Head Screws 2. EB10 Ear Bud Upgrade
5. Antennas x1 3. 4. 4. EXTBNC: BNC Cable 2. #2 Phillips Head
6. Power Supply x1 for Front Mounting Antenna Screwdriver
7. Quick Start Guide x1 (4 lengths available) 4. 5.
5. CN-BNCPM: BNC Connector
5. 6. for Front Mounting Antenna 1. 2.
Setup Single Rack Mounting (Optional)
1 2 3 4 1
3. Unlimited Receivers
Insert the 5.5mm plug into the DC input Input Connection (XLR): Connect a Input Connection (1/4"): Connect a 1/4" Attach the antenna to the antenna jack Attach the long and short rack ears to
jack, plug the wall wart into a 120VAC shielded XLR microphone cable to the cable to the transmitter's left and right and position at a 45 angle if possible. o either side of choice using the provided
outlet. transmitter's left and right XLR input, 1/4" input, connect the other end into screws. Align and screw into the rack.
connect the other end into your signal your signal source's left and right outputs.
source's left and right outputs.
can be added
Dual Rack Mounting (Optional) Operation
1 2 3 4 1
Screw one short rack ear on the left side Screw one short rack ear on the right Align both transmitters so that the coupler Align the dual transmitters to the rack Press the Power button to power on
of the first transmitter, and one coupler side of the second transmitter, and one halves fit, and screw them together. and screw into the rack. the Transmitter. 4.
half onto the right side of the same coupler half onto the left side of the EXTBNC: BNC Cable
transmitter using the provided screws. same transmitter.
2 3 4
for Front Mounting Antenna
Insert Two AA Alkaline Batteries into the Turn the Level knob clockwise to power Insert the ear buds into the receiver and
Receiver. on the Receiver. adjust the volume to a comfortable level.
(4 lengths available)
5.
CN-BNCPM: BNC Connector
for Front Mounting Antenna
3
Input Connection (1/4"): Connect a 1/4"
cable to the transmitter's left and right
1/4" input, connect the other end into
your signal source's left and right outputs.
3
Align both transmitters so that the coupler
halves fit, and screw them together.
4
Insert the ear buds into the receiver and
adjust the volume to a comfortable level.
1. 2.
3.
4. 5.
4
Attach the antenna to the antenna jack
o
and position at a 45 angle if possible.
4
Align the dual transmitters to the rack
and screw into the rack.
Quick Start Guide
AS-900
What May be Needed
to Rack
(Not Included)
1.
Rack Screws 10/32 x .75",
Phillips Truss Head Screws
2. #2 Phillips Head
Screwdriver
1. 2.
Single Rack Mounting
(Optional)
1
Attach the long and short rack ears to
either side of choice using the provided
screws. Align and screw into the rack.
Operation
1
Press the Power button to power on
the Transmitter.