Related Manuals for TERMOSTROJ TERMO-Kombi
Summary of Contents for TERMOSTROJ TERMO-Kombi
- Page 1 ELECTRIC BOILER FOR CENTRAL HEATING AND WARM WATER PREPARATION TERMO-Kombi USER’S INSTRUCTIONS We reserve the right of changing these instructions without special prior notification TMS-UT-0709-Z07-5...
-
Page 2: Table Of Contents
• 2.1. Construction ............. 1 Adjusting correctly is important for • economical heating. 2.2. Integral parts of the TERMO-Kombi Boiler ..2 At each contact with the manufacturer or • authorized service call to the factory-a 3. Installation ............... 3 number that is printed on the identification label on the boiler. -
Page 3: Introduction
90 system. Because of its design and noise free operation, the TERMO-Kombi may easily fit in the living space. The The Termo-Kombi boilers meet any and all national outer metal sheet is protected by powder coating. regulations and legal standards. Pursuant to the mentioned before, the certification of the product was 2.1. -
Page 4: Integral Parts Of The Termo-Kombi Boiler
2.2. Integral parts of the TERMO-Kombi Boiler 1. Central heating primary flow 2. Central heating return flow 3. External shell of the boiler 4. Boiler 5. Thermal insulation 6. Electric heaters 7. Control panel 8. Boots for el. terminals 9. Contactors 10. -
Page 5: Installation
BREAKER ON THE INLET LINE OF SANITARY WATER ON THE BOILER. 3.2. Assembly TERMO-Kombi is foreseen for the wall assembly and for the easier assembly, on the backside there is foreseen the suspension support. For the suspension you may use metal wall plugs with the screw M8 or M10 or stronger plastic wall plugs –... -
Page 6: Assembly (Continued)
Illustration of how to correctly vent the water circle on upper side of Termo-Kombi. Protection cap should be release on automatic venting pots (1 and 2). Plastic pipe should be attached to valve (3) prior venting the water circle. -
Page 7: Connection To The Power Network
3.3. Connection to the power network For power supply connection on all Termo-Kombi boilers, MCB (miniature circuit breaker) is used, providing same time protection for boiler and connection point for external power cables. Note: When connecting power cable please observe live and neutral marks inside boiler. -
Page 8: Use Of The Product
4. Use of the product Control panel Multipurpose – temperature indicator (temperature of Switch for central heating switching on and off boiler, sanitary water, adjustment of temperature) Sanitary water temperature adjustment Signalization of operation degree of heaters (1., 2., 3.) Switch for switching on and off the sanitary water Signalization of air appearance in the boiler (red light) preparation... -
Page 9: Use Of The Boiler
4.1. Use of the boiler First putting on at the beginning of a season For the first putting on at the beginning of a central heating season, the first step should be to put on the boiler by means of the switch for central heating (7), temperature in the boiler (1) should be adjusted to 30°C (in this was the heaters are disconnected and only circulation pump is in operation). -
Page 10: Manipulation With Automatic Equipment
4.2. Manipulation with automatic equipment Putting on and of the sanitary water preparation The boiler is switched on by means of the main switch (9), for switching on, the switch should be put in the position 1. Upon switching on a desired water temperature in boiler is displayed for 5 seconds, signalization of sanitary water preparation is twinkling (10). - Page 11 Parallel operation of central heating and sanitary water When both modes of operation are active, central heating and sanitary water preparation, the boiler prefers sanitary water. If there is a requirement for warm water, the boiler starts with preparation of sanitary water, the lamp (10) turns on, whereas the boiler operation signalization turns off (5);...
-
Page 12: Recommendations For Optimal Use
4.4. Recommendations for optimal use Central heating For optimal use of the boiler and electric power consumption, we recommend the use of quality room thermostat connected to the boiler. Daily temperature should be between 20°C i 22°C (for each degree above 22°C the consumed energy is increasing exponentially). -
Page 13: Survey Of Possible Defects And Irregularities In
6. Survey of possible defects and irregularities in operation DEFECT CAUSE ELIMINATION - at switching on, no voltage on no feed from net on one or check on serial clamps of the control panel more phases the boiler whether there is fuse 2,5A on the control feeding panel blown... - Page 14 - pressure in heating system is defective expansion vessel, if there is water on the valve varying too low or too high pressure for pumping the vessel, in the vessel replace the vessel, pressure in the vessel should be 0,5 – 0,8 bar - RCCB switch is ejecting defective heater, replace the heater,...
-
Page 15: Technical Specification
Valve for venting the boiler Safety valve at 3 bar Central heating starting line Safety valve at 8 bar Sanitary water outlet line (warm water) Power and room thermostat inlet Filling valve TERMO-Kombi Boilers Type of the device Characteristics Units TERMO TERMO TERMO... - Page 16 TABLE OF RECOMMENDED FLOWS Recommended Maximum Power range Minimum flow Optimal flow flow work area [kW] [l/min] [l/min] [l/min] [l/min] 10-35 15-40 15-55 25-70 25-80 30-100 SUPPLY CHARACTERISTICS POWER Nominal Fuse current Rated short-circuit Rated short-circuit Min. conductor's Fuse type RCCB switch type current breaking capacity...