Related Manuals for MacAllister MCS2400
Summary of Contents for MacAllister MCS2400
- Page 1 2400W Electric Chain Saw MCS2400 Barcode: 5052931013890 MNL_MCS2400_DFT_GB_V05_111108.indd 1 11/8/11 5:17:13 PM...
-
Page 2: Table Of Contents
Let’s get started These instructions are for your safety. Please read through them thoroughly before use and retain them for future reference. started... Getting Before you start Safety more detail... Product functions Operation Care and maintenance Trouble shooting Recycling and disposal Technical and legal information Guarantee EC declaration of conformity... - Page 3 Before you start MCS2400 by MacAllister Your product MNL_MCS2400_DFT_GB_V05_111108.indd 3 11/8/11 5:17:15 PM...
-
Page 4: Before You Start
Before you start MCS2400 by MacAllister 1. Front handle 14. Oil tank cap 2. Front guard/chain 15. Reset button for brake circuit breaker 3. Saw chain 16. Lock-off button 4. Guide bar 17. On/off switch 5. Sprocket nose 18. Cable strain relief 6. - Page 5 Before you start MCS2400 by MacAllister You will need (items not supplied) (items supplied) Saw chain oil Saw chain Guide bar cover Assembly Assemble the guide bar and saw chain before operation. Follow the operating instructions step-by-step and use the pictures provided as a visual guide to easily assemble the product.
- Page 6 Before you start MCS2400 by MacAllister Assembly WARNING! Always use a saw chain designed as “low- kickback” or a saw chain which meets the low-kickback requirements! A standard saw chain (a chain which does not have the kickback reducing guard links) should only...
- Page 7 Before you start MCS2400 by MacAllister > Replace the cover (9) and slightly tighten the locking wheel (7) (Fig. 5, b). Do not tighten the locking wheel completely; saw chain tensioning is required first. Fig. 5 NOTE: The saw chain (3) has not yet been tensioned.
- Page 8 Before you start MCS2400 by MacAllister Assembly > Set the product on a suitable flat surface. > Turn the tension wheel (8) until the chain “tie straps” are just touching the bottom edge of the guide bar (4) (Fig. 6).
- Page 9 Before you start MCS2400 by MacAllister Lubrication WARNING! The product is not filled with oil. It is essential to fill the product with oil before using it! Never operate the product without chain oil or with an empty oil tank, as this...
- Page 10 Before you start MCS2400 by MacAllister Lubrication > Check the oil level window (19) prior to start-up and regularly during operation. Refill oil when the oil level is lower than “MIN” marking (Fig. 11). > Wipe up spilled lubricant with a soft cloth and refit the tank cap (14).
- Page 11 Before you start MCS2400 by MacAllister Connection to the power supply WARNING! For your safety, it is required that the plug attached to this product is always connected to an extension cable! The extension cable must be suitable for outdoor use with sockets protected against water splashing! Ensure the extension cable is of the proper size and type for your product (≥...
-
Page 12: Safety
Safety MCS2400 by MacAllister Check that you have noted all the following instructions: Before starting you must have fully read and understood the entire instruction manual. Working with this product is demanding; therefore ensure you are physically and mentally fit to complete the job safely. -
Page 13: In More Detail
MCS2400 by MacAllister more detail... Product functions Operation Care and maintenance Trouble shooting Recycling and disposal Technical and legal information Guarantee EC declaration of conformity MNL_MCS2400_DFT_GB_V05_111108.indd 13 11/8/11 5:17:28 PM... -
Page 14: Product Functions
MCS2400 by MacAllister Intended use This chain saw MCS2400 is designated with a rated input of 2400 Watts. The product is intended for cutting logs with a thickness of max. 435 mm. It must not be used for cutting other materials, such as plastic, stone, metal or wood that contains foreign objects. - Page 15 Product functions MCS2400 by MacAllister Chain brake The chain brake is a safety mechanism activated by the front guard (2). When kickback occurs the chain stops immediately. Fig. 15 Fig. 16 The chain brake (2) in the The chain brake (2) in the engaged...
- Page 16 Product functions MCS2400 by MacAllister Chain brake > Press the lock-off button (16) with your right thumb, then fully squeeze in the on/off switch (17) with your index finger and hold it in position. > While the motor is running, activate the chain brake (2) by moving your left hand forward against the chain brake (2).
- Page 17 Operation MCS2400 by MacAllister General operation > Check the product, its power cord and plug as well as accessories for damage before each use. Do not use the product if it is damaged or shows wear. > Double check that accessories and the guide bar/saw chain are properly fixed.
-
Page 18: Operation
Operation MCS2400 by MacAllister Basic operating / cutting procedure > The saw chain (3) must be running at full speed before it makes contact with the wood. Use the spike bumper (22) to secure the product onto the wood before starting to cut and use it as a leverage point while cutting (Fig. - Page 19 Operation MCS2400 by MacAllister Kickback WARNING! Beware of kickback! Kickback can lead to dangerous loss of control of the product and result in serious or fatal injury to the operator or anyone standing close by! Always be alert because rotational kickback and...
- Page 20 Operation MCS2400 by MacAllister Kickback > With a basic understanding of ‘kickback’, the element of surprise can be reduced or eliminated. Sudden surprise contributes to the majority of accidents. > Keep a good firm grip on the product with both hands, your right hand on the rear handle (12) and your left hand on the front handle (1), when the motor is running.
- Page 21 Operation MCS2400 by MacAllister > An escape path should be planned cleared necessary before cuts started. The escape path should extend back and diagonally to the rear of the expected line of fall (Fig. 27). > Before felling is started, consider the natural lean of the tree, the Fig.
- Page 22 Operation MCS2400 by MacAllister Limbing and pruning Limbing removing branches from a fallen tree. When limbing leave larger lower limbs to support the log off the ground. Remove the small limbs in one cut (Fig. 29). Branches under tension should be cut from the bottom up to avoid binding Fig.
- Page 23 Operation MCS2400 by MacAllister Bucking a log Bucking is cutting a log into lengths. It is important to make sure your footing is firm and your weight is evenly distributed on both feet. When possible, the log should be raised and supported by the use of limbs, logs or chocks.
- Page 24 Operation MCS2400 by MacAllister Bucking a log > Support small logs on a sawing stand or another log while bucking (Fig. 34). Fig. 34 > If the wood diameter is large enough for you to insert a soft bucking wedge without...
- Page 25 Care and maintenance MCS2400 by MacAllister The golden rules for care WARNING! Always switch the product off, disconnect it from power supply and let the product cool down before performing inspection, maintenance and cleaning work! > Keep the product clean. Remove debris from it after each use and before storage.
-
Page 26: Care And Maintenance
Care and maintenance MCS2400 by MacAllister Sprocket nose NOTE: It is not necessary to remove the saw chain (3) to lubricate the sprocket nose (5). Lubrication can be done on the job. > Clean the sprocket nose (5). > Using a disposable lube gun,... - Page 27 Care and maintenance MCS2400 by MacAllister NOTE: The condition of the oil passages can be easily checked. If the passages are clear, the chain will automatically give off a spray of oil within seconds of the product starting. Your product is equipped with an automatic oiling system.
- Page 28 Care and maintenance MCS2400 by MacAllister Guide bar and saw chain maintenance > Check the saw chain for possible wear and damages. Replace it with a new one if required. Experienced users can sharpen a dull saw chain (see section “Saw chain sharpening” below).
- Page 29 Care and maintenance MCS2400 by MacAllister Power cord > If the power cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a safety hazard. UK plug If you need to replace the fitted plug, then follow the instructions below.
- Page 30 Care and maintenance MCS2400 by MacAllister Repair > This product does not contain any parts that can be repaired by the consumer. Contact a qualified specialist to have it checked and repaired. Storage > Clean the product as described above.
-
Page 31: Trouble Shooting
Trouble shooting MCS2400 by MacAllister Trouble shooting Suspected malfunctions are often due to causes that the users can fix themselves. Therefore check the product using this section. In most cases the problem can be solved quickly. WARNING! Only perform the steps described within these... -
Page 32: Recycling And Disposal
Recycling and disposal MCS2400 by MacAllister Recycling and disposal > Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice. > Petrol, oil, old oil, a mixture of oil and petrol and objects soiled with oil e.g. -
Page 33: Technical And Legal Information
Technical and legal information MCS2400 by MacAllister Technical specifications General > Rated voltage : 230 - 240 V~, 50 Hz Rated input : 2400 W > > Rated no load speed n : 8680 min > Cutting length : 435 mm >... - Page 34 Technical and legal information MCS2400 by MacAllister Technical specifications WARNING! Depending on the actual use of the product the vibration values can differ from the declared total! Adopt proper measures to protect yourself against vibration exposures! Take the whole work process including times...
- Page 35 Technical and legal information MCS2400 by MacAllister Caution / Warning. Wear safety helmet! Read the instruction Wear face protection! manual. Wear hearing Wear protective protection. gloves. Wear eye protection. Wear safety footwear. Wear respiratory protection. Switch the product off and disconnect it from the power supply before assembly, cleaning, adjustments, maintenance, storage and transportation.
- Page 36 Technical and legal information MCS2400 by MacAllister Symbols Guaranteed sound power level value in 105 dB This product is of protection class II. That means it is equipped with enhanced or double insulation. The product complies with the applicable European directives and an evaluation method of conformity for these directives was done.
- Page 37 Technical and legal information MCS2400 by MacAllister Work area safety > Keep work area clean and well lit. Cluttered or dark areas invite accidents. > Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.
- Page 38 Technical and legal information MCS2400 by MacAllister Safety warnings > Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
- Page 39 Technical and legal information MCS2400 by MacAllister > Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
- Page 40 Technical and legal information MCS2400 by MacAllister Safety warnings When cutting a limb that is under tension be alert for spring > back. When the tension in the wood fibres is released the spring loaded limb may strike the operator and/or throw the chain saw out of control.
- Page 41 Technical and legal information MCS2400 by MacAllister > Maintain a firm grip, with thumbs and fingers encircling the chain saw handles, with both hands on the saw and position your body and arm to allow you to resist kickback forces.
- Page 42 Technical and legal information MCS2400 by MacAllister Safety warnings Vibration and noise reduction To reduce the impact of noise and vibration emission, limit the time of operation, use low-vibration and low-noise operating modes as well as wear personal protective equipment.
- Page 43 Technical and legal information MCS2400 by MacAllister > Injuries and damage to property due to broken application tools or the sudden impact of hidden objects during use. > Danger of injury and property damage caused by flying objects. > Injuries and damage to property to due to thrown and fallen objects.
-
Page 44: Guarantee
Guarantee MCS2400 by MacAllister Guarantee > This product has been manufactured to a high quality standard. It is guaranteed against faulty materials and workmanship for 24 months from purchase, please retain your till receipt as proof of purchase. > If the product is found to be defective within the relevant time... -
Page 45: Ec Declaration Of Conformity
EC declaration of conformity B&Q PLC. CHANDLERS FORD, HANTS, SO53 3LE Declare that the product 2400W Electric Chain Saw MCS2400 Complies with the essential health and safety requirements of the following Directives: EC Machinery Directive 2006/42/EC The Low Voltage Directive 2006/95/EC The EMC Directive 2004/108/EC The Outdoor Noise Directive 2000/14/EC&2005/88/EC... - Page 46 www.diy.com B&Q plc. GB-IE Chandlers Ford, Hants, SO53 3LE, United Kingdom MNL_MCS2400_DFT_GB_V05_111108.indd 46 11/8/11 5:17:42 PM...