Table of Contents
Advertisement
Quick Links
Microwave Drawer : SMD2477ASC, SMD2477AHC, SMD3077ASC
SPECIAL WARNING
INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.
IMPORTANT: SAVE this installation manual FOR LOCAL ELECTRICAL INSPECTOR'S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CLEARANCES AND DIMENSIONS
For SAFETY CONSIDERATIONS do not install drawer in any combustible cabinetry, which is not in accord with the stated
clearances and dimensions on pages 2 - 5. See Figure 1 (for 24") or Figures 4 and 5 (for 30").
UNPACKING YOUR MICROWAVE DRAWER
• Remove all packing
materials from inside
the Microwave Drawer.
DO NOT REMOVE
THE WAVEGUIDE
COV E R, wh ich is
located on the top
of t he M ic rowave
Drawer.
• Remove the feature
sticker, if there is one.
Check the drawer for
any damage, such as
misaligned or bent
drawer, damaged drawer seals and sealing surfaces, broken
or loose Microwave Drawer guides and dents inside the cavity
or on the front side of the drawer. If there is any damage, do
not operate the Microwave Drawer and contact your dealer or
a SHARP AUTHORIZED SERVICER.
IMPORTANT NOTES TO THE INSTALLER
• Read all of the Installation Manual before installing the
Microwave Drawer.
• Remove all packing material before connecting the electrical
supply.
• Observe all governing codes and ordinances.
• Be sure to leave these instructions with the consumer.
INSTALLATION MANUAL
Sealing
surface
Waveguide
cover
Oven
cavity
IMPORTANT NOTES TO THE CONSUMER
Keep this manual with your Operation Manual for future
reference.
• As when using any microwave oven generating heat, there
are certain safety precautions you should follow. These are
listed in the Operation Manual. Read all and follow carefully.
• Be sure your Microwave Drawer is installed and grounded
properly by a qualified installer or service technician.
IMPORTANT SAFETY INSTRUCTIONS
Sealing
Mounting
surface
flange
exactly, a fire or electrical shock may result that could cause
property damage, personal injury or death.
Drawer must be secured by a properly installed Anti-Tip
block.
• This Microwave Drawer must be electrically grounded in
accordance with local codes.
• Make sure the wall coverings and the cabinets around the
Microwave Drawer can withstand the heat generated by the
Microwave Drawer.
the area where a Microwave Drawer is in use. Never leave the
drawer open when the microwave is unattended.
result in serious injuries and can also cause damage to the
Microwave Drawer.
• Do not use the Microwave Drawer as a storage space.
This creates a potentially hazardous situation.
• Check that the time-of-day is in the display. If not, touch
STOP/CLEAR to prevent unintended use.
E 1
E 1
If the information in this manual is not followed
To reduce the risk of tipping, the Microwave
Never leave children alone or unattended in
Stepping, leaning or sitting on the drawer may
T IN SK B 24 9 MRR0
Advertisement
Table of Contents
Related Manuals for Sharp SMD2477ASC
Summary of Contents for Sharp SMD2477ASC
- Page 1 Microwave Drawer : SMD2477ASC, SMD2477AHC, SMD3077ASC INSTALLATION MANUAL SPECIAL WARNING INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER. IMPORTANT: SAVE this installation manual FOR LOCAL ELECTRICAL INSPECTOR’S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. CLEARANCES AND DIMENSIONS For SAFETY CONSIDERATIONS do not install drawer in any combustible cabinetry, which is not in accord with the stated clearances and dimensions on pages 2 - 5.
-
Page 2: Clearances And Dimensions
Power cord access hole in cabinet should be a minimum 1 1 /2" diameter N. Floor must support 100 lb (45.4 kg) hole and deburred of all sharp edges. O. 24" (609.6 mm) cabinet minimum P. 15-9/16" (395.27 mm) opening... - Page 3 This drawing represents a typical standard cabinet. If installed in custom cabinets with extended counter tops, take into account visibility and access to controls. See Figure 3. Move oven location downward for extended countertops Extended countertops Figure 3 A. 25" (635 mm) B.
- Page 4 Power cord access hole in cabinet should be a minimum This Microwave Drawer can be installed below any electric or " diameter hole and deburred of all sharp edges. gas wall oven. Always allow sufficient power cord length to the IMPORTANT electrical outlet to prevent tension.
- Page 5 A. 6" (152.40 mm) B. Suggested electrical outlet location* C. Anti-Tip block D. 5" (127 mm) E. 3-1/2" (88.90 mm) F. 4" (101.60 mm) G. 22-1/8" (561.97 mm) minimum, 28-7/16" (722.3 mm) maximum H. 14-13/16" (376.24 mm) to bottom of Anti-Tip block I.
- Page 6 This drawing represents a typical standard cabinet. If installed in custom cabinets with extended counter tops, take into account visibility and access to controls. See Figure 7. Move oven location downward for extended countertops Extended countertops Figure 7 A. 25" (635 mm) B.
-
Page 7: Anti-Tip Block
ANTI-TIP BLOCK NORMAL INSTALLATION STEPS ANTI-TIP BLOCK INSTALLATION INSTRUCTIONS To reduce the risk of tipping of the drawer, the Anti-Tip block must be properly installed located 14 -inches above the floor on which the Microwave Drawer will sit. The 6-inch Anti-Tip block must be provided by the installer. See Figures 1, 4 and 5. The Anti-Tip block prevents serious injury that might result from spilled hot liquids. -
Page 8: Drawer Installation
Refer to the warranty in your Operation Manual for Sharp’s toll-free service number and address. Please call or write if you have inquiries about your microwave product and/or need to order parts.