Summary of Contents for Plum ecoMAX 200 W
- Page 1 Dzia Zintegrowanego Systemu Zarz dzania Boiler regulator ecoMAX 200 W FOR SOLID FUEL BOILERS WITH A FAN OPERATION AND MAINTENANCE MANUAL ISSUE: 1.3 10.034 APPLICABLE TO 10.035 SOFTWARE 10.036 2010-04-14...
-
Page 3: Table Of Contents
TABLE OF CONTENTS 12.4 3 ..... 21 INIMUM BOILER TEMPERATURE N Safety ..............4 12.5 4 ..... 21 AXIMUM BOILER TEMPERATURE N General information .......... 5 12.6 5 ..... 22 UEL SHORTAGE DETECTION TIME N Information about documentation ....5 12.7 6........ -
Page 4: Safety
Safety Incorrect selection parameters cause Safety requirements malfunction of the boiler (e.g. specified in individual sections overheating of the boiler, etc.). this manual. Apart from The regulator is intended for them, following boiler manufacturers. Before requirements should applying the regulator, a boiler particular be applied: manufacturer should check if the regulator‟s mating with the... -
Page 5: General Information
General information significant for safety issues, hence the user should read both parts of the manual. The ecoMAX 200 series boiler regulator is an electronic device intended for solid fuel We are not responsible for any damages boilers. It performs the following functions: caused by failure to observe these •... -
Page 7: Regulator Instruction Manual
REGULATOR INSTRUCTION MANUAL ecoMAX 200 W... -
Page 8: Operating The Regulator
6. Boiler regulation mode – PID function, Operating the regulator 7. Room thermostat - this symbol lights up This section briefly describes when the temperature inside the room regulator should be operated. reaches the preset value contacts are disconnected) Description of buttons and display 8. -
Page 9: Iring Up Activation Of Airflow
Combustion regulation methods Caution: The combustion regulation regulator features three selectable methods described below will methods regulating combustion properly regulate the combustion process. process, as long as the boiler is operated accordance with CLASSIC regulation (regulation mode 1) recommendations boiler In order to enable the CLASSIC mode of manufacturer. - Page 10 The same applies to presetting excessively high temperatures of temperature; please note that the value in water in the boiler. PLUM sp. z o.o. the upper part of the thermometer symbol, company recommends to operate e.g.: 20°C, means 200°C. Unless the boiler...
-
Page 11: Supervision
optimal emission temperature causes the boiler furnace chamber. The fan is excessive heating up of the boiler, it is best enabled for blow-off time at every blow-off to store the surplus energy in a thermal interval. These times must be selected in buffer. -
Page 12: Peration Without Airflow
12.15 Do not enable the SUMMER function in a hydraulic system with a thermal buffer 7.11 Operation without airflow Unless the START button is pressed in the main display window (right after turning the regulator on via the mains switch), the device controls only the pumps. -
Page 13: Regulator Installation And Service Settings Manual
REGULATOR INSTALLATION AND SERVICE SETTINGS MANUAL ecoMAX 200 W... -
Page 14: Technical Data
Hydraulic diagram Technical data Feed 230V~; 50Hz; Current consumed by regulator I = 0,02 A Maximum rated current 3(3) A Regulator protection rating IP40, IP00 Ambient temperature 0...50 C Storage temperature -15...60 C 5 - 85% without Relative humidity condensation of vapour Temperature measurement 0...100 C... -
Page 15: Storage Conditions And Transport
depletion and turns the fan off. Moreover, it Storage and transport temperature cannot allows operation in the PID-EMISSION boiler exceed the scope of -15…60 °C. regulation mode, preview During transport, the device cannot be emission temperature. exposed to vibrations greater than those typical of normal road transport. -
Page 16: Ip Protection Rate
Drawing 8. Fitting the regulator in a mounting plate, where: 1 - regulator, 2 – sheet metal screw 2.9x9, 3 – Drawing 10. Conditions of enclosing the regulator hole plug. The regulator enclosure must provide degree protection appropriate environmental conditions which regulator will be used. -
Page 17: Protective Connections
three core (with protective wire), accordance with applicable regulations. Diagram electrical connections presented in Drawing 12. The connection wires should not have contact with surfaces of room temperature exceeding the nominal temperature of their operation. Terminals L, N and number 1-8 are intended only for connecting devices with mains supply 230V~. -
Page 18: Connecting Emission Sensor
11.6 Connecting emission sensor 11.7 Connecting temperature sensors The regulator is compatible only with sensors type CT4 (sensor of boiler and hot utility water) and CT2s (emission sensor). It is prohibited to use different sensors. Sensor leads can be extended with wires with section of at least 0,5mm . -
Page 19: First Start-Up Of The Regulator
11.10 Connecting room thermostat 1659 1696 1733 Table 1. Values of resistance of temperature sensors To make the boiler more economical, and the CT4. temperature in the heated rooms more Temp. Min. Nom. Max. stable, install a room thermostat. °C Ω... -
Page 20: Connecting Temperature Limiter Stb
11.11 Connecting temperature limiter additional thermal protection cannot used instead mandatory order prevent boiler from safety temperature limiter! overheating regulator 11.13 Smooth fan start malfunction, a safety temperature limiter, During every activation of the fan, the appropriate for the given boiler and heating regulator gradually increases the airflow system, should be fitted. -
Page 21: Service Settings
its being cooled down by hot water returning 12 Service settings from the system. Enter the service settings by holding the „F” button in the main window for 8 seconds. Disabling the central heating pump Exit from service settings made on its own does not guarantee automatically after a period of idleness, or protecting the boiler against retting,... -
Page 22: Fuel Shortage Detection Time N5
temperature (point 11.10). As a result of Set the value in accordance with the blocking the central heating pump, the boiler manufacturer‟s temperature in the heated rooms will drop, recommendations boiler will reach preset temperature faster switch SUPERVISION mode. Yet, long 12.6 Fuel shortage detection time n5 blockade of the central heating pump will... -
Page 23: Boiler Preset Temperature Increase R2
12.13 Boiler preset temperature 12.16 Fuel shortage detection – emission temperature r5 increase r2 The value of the r5 parameter determines Boiler preset temperature increase by hot the temperature of emission below which fuel utility water r2. This parameter specifies by shortage detection will be made on the basis many degrees... -
Page 24: Power Supply Decay
Fast detection of fuel shortage decreases 13 Firmware losses of heat caused by the fan operating WARNING!!! Values of the following with no fuel, and it allows to sustain fire for a parameters can be modified only by longer time, during which the boiler can be qualified staff of the boiler manufacturer refuelled without the need of firing it up There is a menu of factory parameters in the... -
Page 25: Boiler Temperature Sensor Damage Al2
cause stoppage of the boiler. Before the boiler reaches the P0 temperature, regulator will attempt to drop the excessive heat to the hot utility water tank. If the hot utility water tank reaches the Drawing 2 AL1 alarm maximum temperature permitted by the r3 parameter, the hot utility No sound signal will be given. -
Page 26: Description Of Possible Faults
16 Description of possible faults Signs of a fault Hints 1. The display blank Check: despite connection if the main fuse is burnt-out, replace if so, the supply network. Check: whether the hot utility water tank is filled at the time and the 2.
Need help?
Do you have a question about the ecoMAX 200 W and is the answer not in the manual?
Questions and answers