Advertisement
4.2
Optional wheel assembly
4.2.1. The wheel assembly is supplied ready to fit.
4.2.2. Raise the unladden platform, as described in section 5.
4.2.3. Fit the wheel assembly into the brackets on the frame, as
shown in fig. 1.
4.2.4. Ensure the locking tab is in a horizontal position and secure
the wheel assembly using two elastic pins, 4 X 40.
5. OPERATING INSTRUCTIONS
5.1. Operating the platform
5.1.1. Before use, check that the lift is level on a suitable surface,
the wheel assembly (if fitted) is fully raised, and that the platform
is fully lowered.
F
WARNING! Ensure that there is adequate clearance between
the underside of the mini tractor and the point where the mobile
p
ramp and platform meet. Failure to do so may cause damage.
5.1.2. Position the mini tractor on the platform and apply the handbrake.
5.1.3. Raise the platform by pumping the foot pedal.
5.1.4. When fully raised, position the safety bar (17) between the arm (16) and the base (8) to prevent the platform from accidentally descending.
5.1.5. When work is complete, check under the platform to ensure there are no obstructions and that it is safe to lower the unit.
5.1.6. Remove the safety bar (17).
5.1.7. Press the release foot pedal to lower the platform.
5.2. Operating the wheel assembly
F
WARNING! The wheel assembly is designed for manouvering the lift unladden.
5.2.1. Raise the unladden platform and position the safety bar the prevent the platform from accidentally descending.
p
5.2.2. Press down on the wheel assembly foot pedal to raise the frame sufficiently to allow the locking tab to be positioned vertically.
5.2.3. Release the foot pedal.
5.2.4. Position the foot pump such that it can move safely and freely with the lift.
5.2.5. The platform can now be manouvered.
F
WARNING! Ensure there are no obstructions underneath the frame before disengaging the wheel assembly.
5.2.6. To disengage the wheel assembly, press down on the wheel assembly foot pedal to raise the frame sufficiently to allow the locking tab
p
to be positioned horizontally.
5.2.7. Release the foot pedal.
6. MAINTENANCE
IMPORTANT: Only fully qualified personnel should attempt maintenance or repair.
% DO NOT use the lift if it is believed to have been subjected to abnormal shock or load. Inspect and take appropriate action.
6.1.
When the lift is not in use, the platform must be in the lowest position to minimise hydraulic ram and piston corrosion.
6.2.
Keep the lift clean and wipe off any oil or grease. Lubricate all moving parts with acid-free oil.
6.3.
Before each use, ensure components are not damaged, malfunctioning or missing. If any suspect item is found remove the lift from
service and take the necessary action to remedy the problem.
6.4.
Periodically check the pump piston and piston rod for signs of corrosion. Clean exposed areas with a clean oiled cloth.
F
WARNING! Only a good quality hydraulic oil, such as SEALEY HYDRAULIC JACK OIL must be used, DO NOT use brake fluid.
IMPORTANT: NO RESPONSIBILITY IS ACCEPTED FOR INCORRECT USE OF THE LIFT.
Hydraulic products are only repaired by local service agents. We have service/repair agents in all parts of the UK. DO NOT RETURN LIFTS
TO US. Please telephone 01284 757500 to obtain address and ‘phone number of your local agent. If lift is under guarantee please contact
your dealer.
De-commissioning: If and when the lift become completely unserviceable, draw off the oil into an approved container and dispose of the lift and
the oil according to local regulations.
7.
DECLARATION OF CONFORMITY
Declaration of Conformity
Mini Tractor Lift
Model: MT500
98/37/EC Machinery Directive
93/68/EEC CE Marking Directive
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
p
p
p
We, the sole importer into the UK, declare that the product listed below is in conformity with the following standards and directives.
The construction file for this product is held by the Manufacturer and may be inspected, by a
national authority, upon request to Jack Sealey Ltd.
Signed by Mark Sweetman
Sole U.K. Distributor,
01284 757500
Sealey Group,
Bury St. Edmunds, Suffolk.
For Jack Sealey Ltd. Sole importer into the UK of Sealey Quality Machinery.
01284 703534
Fig 1
24th April 2002
E-mail: sales@sealey.co.uk
MT500 - 1 - 240402
Advertisement
