Subscribe to Our Youtube Channel
Summary of Contents for FISBA READYBeam bio 1
- Page 1 Technical Instruction FISBA READYBeam A compact multi-wavelength laser module October 2021...
-
Page 3: Table Of Contents
Warranty conditions 1.4.1 Limits of the warranty Technical system Laser module Installation and commissioning 2.2.1 Unpacking and checking for visible damage 2.2.2 Installation 2.2.3 Operating the FISBA READYBeam 2.2.4 Software Setup 2.2.5 Software interface 2.2.6 Modulation mode Appendix Data sheet... -
Page 4: Safety
Safety Explanation of symbols This symbol is used for all points in these operating instructions to which special attention is to be paid so that all directives, regulations, instructions and the correct work sequence are observed, and to prevent minor or serious damage to the laser system or plant. - Page 5 However, in this case the following requirements apply to the protective cover: · The protective cover must be appropriate to adequately shield the laser radiation. It is therefore necessary to use laser safety glass or laser safety film for viewing windows. ·...
-
Page 6: Warning And Information Labels
Warning and information labels The following warning labels are fitted to laser and processing head: The READYBeam is an OEM certified laser. Please be advised that it has no dedicated Key Switch. If operated via PC with the software installed, be cautioned that sudden- ly unplugging it during “Lasing, ”... -
Page 7: Warranty Conditions
1.4.1 Limits of the warranty No warranty of the suitability of the product for specific applications is provided. FISBA is not liable for indirect, direct or consequential damages caused by the use of this product. Technical system The laser module emits laser radiation with different wavelengths. Combination of different laser diodes can emit radiation in the UV, VIS and/or NIR range. -
Page 8: Installation And Commissioning
Check the completeness of the delivery and check that all the items supplied are in good condition. In case of errors please contact FISBA AG (readybeam@fisba.com). If possible, keep the packaging in which the laser system was supplied. It will then be possible to pack the unit in its original packaging and transport it safely in case of repair. -
Page 9: Software Interface
2. Set Power Value 1 (red), Power Value 2 (green) and Power Value 3 (blue): values in % of the max. laser power 3. Switch the Laser on/off with Digital Enable 1, 2 or 3 4. Enter the command with “Write Config” Button The READYBeam software is provided for download at: fisba.com/readybeam-software... -
Page 10: Modulation Mode
2.2.6 Modulation mode On the Interface, the three channels can be set as either on “Digital” to control On/Off modulation via software with a maximum pulse frequency of 100 Hz, or to “ Analog” for external control in On/Off mode or continuous waveform modulation. - Page 11 Software Control External Control Digital Analog On/Off On/Off Continuous m odulation m odulation waveform Up to 100Hz Up to 1M Hz Up to 20kHz On/Off modulation On/Off modulation is best when the operator wants fast and accurate modulation with discrete signals. Digital modulation is possible with two options. Option one is over the SW up to 100Hz.
-
Page 12: Appendix
Appendix Pin configuration and power values Connector: Samtec SFSD-10-28G24.00SR Enable Laser: low = 0V, high = 3.3V Analog In: 0.33V … 3.3V --> 10% ...100% of Laser power Power: +12V … + 24V max. 4A Pin 1 is marked on the connector with arrow (not notch) Pin 1 Analog In- Laser red Pin 2... - Page 13 Module RS-485 Power RS-485 Electric Cable Power Power supply Figure 1...
-
Page 14: Data Sheet
FISBA READYBeam™ Data sheet FISBA READYBeam Technical specifications Technical Specifications Wavelength 405 nm 450 nm 488 nm 520 nm 638 nm 660 nm FISBA READY Beam bio 1 1006061 FISBA READY Beam bio 2 1008062 FISBA READY Beam ind 1 1006062... - Page 15 Definition of QR Code information Specification 1 Item number Specification 2 Serial number Specification 3 Final inspection date EADYBeam Front View - mit Labels lung Oberfläche Werkstoff Kanten gebrochen 0.1...0.2x45° Surface Material Edges chamfered 0.1...0.2x45° Blatt / Anz Gewicht Benennung / Description 99.09 g Sheet / no. of Weight 1 / 1 in Bearbeitung...
- Page 16 FISBA AG ©...
- Page 17 FISBA Photonics GmbH Schwarzschildstrasse 10 12489 Berlin Germany FISBA LLC 6296 E. Grant Rd Suite 150 Tucson, AZ 85712 United States World Plaza, No. 855 FISBA (Shanghai) Co., Ltd. 9F Pudong South Rd. Puong District Shanghai City China fisba.com | readybeam@fisba.com...
Need help?
Do you have a question about the READYBeam bio 1 and is the answer not in the manual?
Questions and answers