Summary of Contents for PLS PLSB
- Page 1 PLS Basic Air Curtains Water With quick guide PLSB For wiring diagram, please see last pages...
-
Page 2: Connect The System
PLS Basic Air Curtains Water Quick guide/start up Enter ID/Operation without control unit The control system can control one or more Check that all constituent parts are present units in parallel (max 9). Each unit must get (see section Constituent parts). -
Page 3: Start Up
PLS Basic Air Curtains Water Start up System supplied with power. Three digits 1.4.0. (software version) is quickly shown in th the status window followed by three horizontal lines. After about 30 seconds the prevailing room temperature is then shown in the status window. -
Page 4: Table Of Contents
PLS Basic Air Curtains Water Contents Quick guide/start up Advice about location Connect the system Wiring diagrams Enter ID/Operation without control unit Start up Constituent parts PLSB Option Max. cable lengths Water control - valve kit Operating modes Operating modes... -
Page 5: Constituent Parts
PLS Basic Air Curtains Water Constituent parts PLSB Integrated in the air curtain PLSUB1, PLSIT, internal PLSB1, integrated control unit Basic Wall unit cover temperature PC Board Base sensor modular cable Dimensions constituent parts Description HxWxD [mm] Controll unit 120x70x35... -
Page 6: Max. Cable Lengths
PLS Basic Air Curtains Water Option PLSRTX, external room CJ4, joint piece CJ6, joint piece temperature sensor modular cable Type Description HxWxD PLSRTX External room temperature sensor 70x33x23 Joint piece for two pcs. RJ11 (4/4) Joint piece for two pcs. RJ12 (6/6) -
Page 7: Water Control - Valve Kit
PLS Basic Air Curtains Water Water control - valve kit SD230 TBVC BPV10 Water control - option VOSP SD230 TBVCMP VAT, adjustment tool for BPV10 valve package. SD230 TRVS Type RSK-no. Description Connection VOS15LF 673 09 35 On/off DN15 VOS15NF... -
Page 8: Operating Modes
PLS Basic Air Curtains Water Operating modes Set values Use arrow up /down to choose desired room temperature, fan speed step and heating step. Operating modes Factory settings gives manual control of fan and heating controlled by thermostat on/off. Push the confirm button and the digit(s) starts to flash. -
Page 9: Control Unit Plsub1 Overview
PLS Basic Air Curtains Water Control unit PLSUB1 Overview Prevailing room temperature 2 0 8 Statuswindow Arrow up Scroll up Confirm Desired room temperature Arrow down Scroll down Fan speed step Alarm Red led Run signal Green led ON/OFF Heating step... -
Page 10: Installer Menu
PLS Basic Air Curtains Water Installer menu Parameter menu P .01 Overheating alarm ON/OFF Keep Confirm button pressed until P00 is Possibility to block the alarm (only valdid for shown in the status window. Use arrow up / units with internal temperature sensor). -
Page 11: Alarm And Error Codes Overheat Protection
PLS Basic Air Curtains Water Alarm and error codes Reset alarm Note! Before resetting, check that the fault is Overheat protection rectified and there is nothing to prevent the Only applies to units with internal sensor. unit from being recommissioned! - Page 12 PLS Basic Air Curtains Water Table - Alarm Alarm Cause Action A.FA Motor alarm Thermal switch has deployed. One Check that nothing is obstructing the or several motors have overheated. unit’s air intake and exhaust. When the (Only units with withdrawn thermal overheated motor has cooled the thermal switches.)
- Page 13 PLS Basic Air Curtains Water...
- Page 14 PLS Basic Air Curtains Water...
- Page 15 PLS Basic Air Curtains Water Wiring diagram - Basic PLSB1 PLSSD230 PLSB1 PLSSD230 PLSB1 PLSUB1 PLSRTX PLSSD230 (optional)
Need help?
Do you have a question about the PLSB and is the answer not in the manual?
Questions and answers