Page 2
California law, and may also be a land covered with grain hay or other 71020 & 70554 Chipper Shredder Operators Manual...
Page 3
The serial number is located on the rotor assembly cover. Crary Company A Division of TerraMarc Industries 237 12th St. NW P.O. Box 849 West Fargo, ND 58078-0849 www.terramarc.com (701)282-5520 FAX: (701)282-9522 www.bearcatproducts.com 71020 & 70554 Chipper Shredder Operators Manual...
Page 5
Please be sure to provide the following information: The SERIAL NUMBER of your machine. The PART NUMBER of the part. The PART DESCRIPTION. The QUANTITY needed. 71020 & 70554 Chipper Shredder Owners Manual Page 1...
3. Keep safety decals clean and leg- ible. Replace missing or illegible safety decals. 4. Familiarize yourself with all of the safety and operating decals on this equipment and on any of its at- tachments or accessories. Page 2 71020 & 70554 Chipper Shredder Owners Manual...
6. Do not climb on machine when op- erating. Keep proper balance and 2. Exclude pieces of metal, rocks, footing at all times. bottles, cans, and other foreign ob- jects from entering the machine. 71020 & 70554 Chipper Shredder Owners Manual Page 3...
PTO. Tie long away from all PTO drive parts. hair back or put under a cap. 11. Do not clean, lubricate, or adjust the PTO shaft when it is running. Page 4 71020 & 70554 Chipper Shredder Owners Manual...
CAN CAUSE MEDICAL • FLAMES BLINDNESS OR BLINDNESS OR HELP • SMOKING INJURY SEVERE BURNS FAST KEEP OUT OF THE REACH OF CHILDREN. DO NOT TIP. KEEP VENT CAPS TIGHT AND LEVEL. 71020 & 70554 Chipper Shredder Owners Manual Page 5...
1. Remove from crate. brake, a different PTO shaft should be used. 2. Place hopper assembly on top of shredder frame. The tabs on the bottom of the hopper should be placed in- 71020 & 70554 Chipper Shredder Owners Manual Page 7...
1. Do not touch the positive (+) battery terminal and any surrounding metal with tools, jewelry or other metal objects. 2. When installing battery cables, connect positive (+) cable first and negative (-) cable last. Page 8 71020 & 70554 Chipper Shredder Owners Manual...
Do not crank starter for 7. Foot Pedal. N/S. Used to engage rotor drive belt. more than 10 seconds or damage may result. Fig. #9, Towable Chipper Shredder 71020 & 70554 Chipper Shredder Owners Manual Page 9...
Clutched PTO shaft Kit (P/N 70885) for tractors with electric brake on the PTO. D. Rotor Access Cover. Used to remove chipper blades and service rotor assembly.4.0 Fig. #11, PTO Chipper Shredder Page 10 71020 & 70554 Chipper Shredder Owners Manual...
If engine kills when engaging foot clutch pedal, either use more choke or increase engine RPM. When the clutch is engaged the foot pedal may vibrate or shake until the engine and rotor have increased to full operating RPM. 71020 & 70554 Chipper Shredder Owners Manual Page 11...
Refer to the Service and Mainte- so it contacts the blades and slows the rotor. nance section for instructions. Fig. # 12, chipping Page 12 71020 & 70554 Chipper Shredder Owners Manual...
¹ PERFORM MORE FREQUENTLY UNDER EXTREMELY DUSTY CONDITIONS. ² HAVE A HONDA ENGINE SERVICE DEALER PERFORM THIS SERVICE. ³ IT IS A GOOD SIGN THAT YOUR CHIPPER BLADES WILL NEED SHARPENING WHEN MATERIAL STOPS SELF FEEDING. 71020 & 70554 Chipper Shredder Owners Manual Page 13...
3. Rotate the rotor so that the bolts holding the chipper Fig. #13, blade sharpening blade are most accessable. 4. Remove the two hex head bolts holding the blade it- self. Repeat for all four blades. Page 14 71020 & 70554 Chipper Shredder Owners Manual...
1/16 to 1/8 of an inch clearance (See Fig. #14). The blade clearance can be viewed through the discharge opening. Rotate the rotor and check the clearance on both chipping blades. Fig. #14, Chipper blade clearance 71020 & 70554 Chipper Shredder Owners Manual Page 15...
4. Using a hammer and punch, drive the knife shaft and test run the machine. through the access hole on the rear of the machine. RECTANGULAR SHREDDER KNIVE KIT TYPICAL SETUP FOR MODEL #'S 70554 & 71020 Fig. #15 ITEM # PART #...
8. To ease reinstallation, smooth any divots or marks in loosening the two set screws and pulling the shaft off. the shaft caused by the set screws. Clean shaft as much as possible before installing into machine. 71020 & 70554 Chipper Shredder Owners Manual Page 17...
When using locking elements, increase torque values by 5%. Torque value for bolts and capscrews are identified by their head markings. Page 20 71020 & 70554 Chipper Shredder Owners Manual...
Page 25
Declaration of Conformity The undersigned manufacturer: Crary Industries, Inc. 237 NW 12 Street P.O. Box 849 West Fargo, ND 58078-0849 Declares that hereunder specified unit: CHIPPER SHREDDER Brand: Crary Bear Cat Type: PTO driven Chipper/Shredder Model Number: 70554S Complies with the requirements of: Machinery Directive 2006/42/EC Garden equipment-Integrally power shredders/chippers-Safety EN13683:2003 + A3 2009 EN ISO 12,100, Part 1-Safety of Machinery-Basic Concepts, General Principles for Design...
Page 26
Crary Company A Division of TerraMarc Industries 237 12th St. NW P.O. Box 849 West Fargo, ND 58078-0849 (701)282-5520 FAX: (701)282-9522 www.bearcatproducts.com Manufactured in the United States of America by Crary Company www.terramarc.com...