Subscribe to Our Youtube Channel
Summary of Contents for Aritech VV600
- Page 1 VV600/VV602Plus Vault Protection System Planning and Installation manual VV600Plus English version Revision 1A: September 2000...
- Page 2 Aritech is a division of InterlogiX B.V. Copyright © InterlogiX B.V. 2000. All rights reserved. No part of this publication may be reproduced, transmitted, stored in a retrieval system, or transmitted in any form, or by any means – electronic, photocopying, recording, or otherwise – without the prior written...
-
Page 3: Table Of Contents
Ultrasound detectors ..................10 4.1.4. Bells ........................10 4.1.5. Human activity....................10 4.2. Detection range of the VV600/602Plus ................10 4.2.1. The vault or safe sensitivity test ................. 11 4.3. Planning a vault protection ....................12 4.4. Planning safe, document cabinet and filing cabinet protection ........ - Page 4 Cable requirements ......................25 6.2. Wiring the detector into the system ................... 25 6.3. Control and function test....................26 6.4. Trouble shooting........................ 28 The Testsystem.......................... 29 7.1. VT705P..........................29 7.2. Wiring and commissioning ....................29 Planning and Installation manual VV600/VV602Plus...
-
Page 5: General Information
At the same time it allows for free movement around the protected area without the risk of creating false alarms. The Aritech VV600Plus system has been field proven to be a very effective and reliable solution for safe, vault and atuomatic teller machines protection. It provides protection with the highest security level possible. -
Page 6: Function
VV602Plus. Each VV600/602Plus seismic detector is a fully equipped vibration detector. This means that all necessary processing electronics is incorporated within each VV600/602Plus unit. Each such unit is ready to co-operate with almost any control panel presently available. No intermediate signal processing is necessary, no vulnerable slave microphones are used. -
Page 7: The Testing System
In order to provide the highest level of security, a daily test of the function of all VV600Plus and VV602Plus detectors in a system is required. Therefore, the Aritech VV600Plus System features a full functional test system that may be operated in parallel with the detection system itself. When activated, the test system will test the following important functions the detection system: •... -
Page 8: Basic Equipment Of The Vv600Plus System
Remote test transmitter VM651P Moveable mounting kit VM604P Steel plate for tack welding VT610P Hand held test unit VM652P Keyhole protection kit VM602P Recess mounting box VT611P Safe application test sensor VM653P Spacer for keyhole kit Planning and Installation manual VV600/VV602Plus... -
Page 9: Functional Description
If a second pulse is not detected within 180 seconds the counter will be reset. Five consecutive counts trigger the alarm. The sensitivity of this channel is pre-set and is not affected by the sensitivity setting of the integration channel. Planning and Installation manual VV600/VV602Plus... -
Page 10: The Explosion Channel
One potential free normally closed contact, opening in alarm. • One open collector transistor output, going out of conductive mode upon alarm condition. The transistor is being protected against short circuit with a series resistor. Planning and Installation manual VV600/VV602Plus... -
Page 11: The Vv602Plus Atm Seismic Detector
3.2. The VV602Plus ATM seismic detector The Aritech VV602Plus detector is a seismic detector capable of detecting vibrations from an attack on an automatic teller machine (ATM) or night safe deposit box to which it is attached, but still disregarding the vibrations created by the normal operation of the protected object. -
Page 12: Planning Instructions
LANNING INSTRUCTIONS 4.1. Planning limitations Although the Aritech seismic detectors are designed to provide a high level of immunity against nuisance alarm sources, some precautions have to be observed. Below we would like to mention some circumstances to preferably avoid: 4.1.1. -
Page 13: The Vault Or Safe Sensitivity Test
7. Take all irregularities into account when spacing detectors. Additional detectors may be required. The separation between vault door and the frame will require an additional detector on the door to encounter a possible attenuation at this point. Planning and Installation manual VV600/VV602Plus... -
Page 14: Planning A Vault Protection
Layout plan It is recommended to prepare a plan to define the location of each sensor and other components of the system. A fold out plan will help in doing this. Planning and Installation manual VV600/VV602Plus... -
Page 15: Planning Safe, Document Cabinet And Filing Cabinet Protection
The VM651P and VM652P have the advantage of forcing the staff to handle the alarm installation properly. It prevents the staff forgetting to remove keys or properly closing the safe doors. Planning and Installation manual VV600/VV602Plus... -
Page 16: Filing Cabinets
If you want to mount a detector on a light weight safe we do recommend you to contact Aritech for further information. The VV602Plus can be mounted directly on the surface, with the movable mounting kit VM651P, or the key-hole protection kit VM652P. -
Page 17: Night Safe Deposit Box
Don’t install sensor on cinder block or other unproved masonry surface without contacting Aritech. Don’t mount sensor on rough surfaces, sand all surfaces. Don’t allow test signal transmitter to make contact with mounting plate or sensor on mansonry installaiton. Planning and Installation manual VV600/VV602Plus... -
Page 18: Installation
• High speed steel drill, diam. 4.2 mm (for M5 tap). • High speed steel drill, diam. 10 mm. • Tap M4 (to mount VV600Plus on steel surface). • Oil to cool drill and tap. Planning and Installation manual VV600/VV602Plus... -
Page 19: Mounting On Steel And Concrete Using A Mounting Plate
D = Mounting hole for expansion plug or recess mounting box. E = Mounting holes for Securitas 2000. F = Mounting hole for expansion plug to the test transmitter, VT705P. G = Mounting holes for accessories Planning and Installation manual VV600/VV602Plus... -
Page 20: Mounting On Concrete
5.4.1. Mounting on concrete In order to surface mount the VV600/602Plus on concrete, a VM600P mounting plate is always required. Please follow the instructions below carefully. Define the exact location of the VV600Plus and hold the VM600P mounting plate to the wall. -
Page 21: Mounting Plate For Welding Vm604P
Weld the VM604P mounting plate to the surface. First weld the points 1,2,3,4 then weld the seams 5 and 6 on the inside of the two slots, see illustration. Mount the VV600/602Plus detector to the VM604P mounting plate, using the three M4 screws supplied. -
Page 22: Mounting Of Accessories
7. When the casting is completed mount the VV600Plus detector on the VM600P mounting plate supplied with the VM602P. 8. After completion of the installation and a successful test, mount the cover plate with the enclosed screws. Planning and Installation manual VV600/VV602Plus... -
Page 23: The Vm603P Weather Protection Box
100 Ohm/2 W gives approx. 1,5 W) in the mounting box and drill a small drain hole in the lowest point of the box. This will give a far better result then trying to seal the box with silicone, which will only result in condensation problems. Planning and Installation manual VV600/VV602Plus... -
Page 24: The Movable Mounting Plate Kit Vm651P
On metal surface mount exactly as the night position plate. On other surfaces than steel suitable screws and expanders have to be selected by the installer. Mount the VV600/602Plus detector on the base plate of the VM651P kit with the three screws supplied. -
Page 25: The Vm652P Key-Hole Protection Kit
Mounting holes A are used for the VM652P. Drill/tap mounting holes as described in chapter 5.2. Mount the VV600/602Plus detector on the VM652P cover plate and wire the detector according to the desired system configuration. The micro-switch inside the VM652P should preferably be wired into the detector’s alarm loop to inhibit arming the alarm system if the keyhole... -
Page 26: The Junction Box Vm655P
26 terminal, two of which are used for the tamper switch and one for the screen to the base. There is a plastic strap for strain relief for the cable and flexible conduit. Planning and Installation manual VV600/VV602Plus... -
Page 27: Connecting The Detector
10 cm of cable after the strain relief. Remove the wire insulation with about 1 cm. Wire the terminals according to wiring diagram below. (Illustration A: Form-A relay. and illustration B: Form-C relay) Planning and Installation manual VV600/VV602Plus... -
Page 28: Control And Function Test
After five blows, the VV600Plus shall alarm. To protect the surface from damage it is advised to use a small aluminium plate between hammer and surface. This test simulates the attack with hammer and chisel and is only valid for VV600Plus. Planning and Installation manual VV600/VV602Plus... - Page 29 Do not forget to set the detector’s sensibility at the right value. Close the lid of the detector and check for closed-loop condition of the tamper-loop. Perform a functional test of both alarm and tamper signals according to panel specifications. Planning and Installation manual VV600/VV602Plus...
-
Page 30: Trouble Shooting
6.4. Trouble shooting Planning and Installation manual VV600/VV602Plus... -
Page 31: The Testsystem
ESTSYSTEM 7.1. VT705P The VT705P is a testsystem consisting of a testgenerator inside the VV600/602Plus and a crystal unit which is mounted on the protected object, inside the detector housing. There are two possiblitities for testing: Test disabled (ex-factory setting). - Page 32 4466-1A...
Need help?
Do you have a question about the VV600 and is the answer not in the manual?
Questions and answers