Ambiance Fireplaces Outlander-19 Installation And Operation Manual

Ambiance Fireplaces Outlander-19 Installation And Operation Manual

Advertisement

AMB9010
This wood appliance needs periodic inspection and repair. It is against United States federal regulations to operate this wood
appliance in a manner inconsistent with the operating instructions in this manual.
INSTALLER:
Leave this manual with the appliance.
CONSUMER:
Retain this manual for future reference.
SAFETY INFORMATION
WARNING
!
If the information in these instructions are not followed exactly, a fi re
or explosion may result causing property damage, personal injury or
death. Please read the entire manual before you install and use your
appliance. This heeater has not been tested with an unvented gas log
set. To reduce risk of fi re or injury, do not install an unvented gas log
set into the heater.
- This heater can be very hot when burning.
- Combustible materials such as fi rewood, wet clothing, etc. placed
too close can catch fi re.
- Children and pets must be kept from touching the heater when it is
hot.
- The chimney must be sound and free of cracks. Before installing
this appliance, contact the local building or fi re authority and follow
their guidelines.
- Operate only with the doors tightly closed.
- Burn wood behind the log retainer directly on the fi rebricks.
- Do not use an elevated grate or otherwise raise the fi re.
- This appliance is designed to burn natural wood only. Higher
effi ciencies and lower emissions generally result when burning air
dried seasoned hardwoods, as compared to softwoods or to green
or freshly cut hardwoods.
- Do not start a fi re with chemicals or fl uids such as gasoline, engine
oil, etc.
- Do not burn trash or garbage, lawn clippings/waste, rubber,
waste petroleum products, paints or paint thinners/solvents, plastic,
materials containing asbestos, construction debris, railroad ties or
treated wood, manure or animal remains, salt water driftwood or
salted materials, unseasoned wood, coal, charcoal, coloured paper,
cardboard, plywood or particleboard. Burning these materials may
result in release of toxic fumes or render the appliance ineffective and
cause smoke.
- Do not let the appliance become hot enough for any part to glow
red.
Wood Stoves ONLY
- At least 14 squares inches (90.3 square centimeters) of outside air
must be admitted to the room or directly to the appliance through a
4" (101.6mm) diameter pipe.
- KEEP THE STOVE TOP TEMPERATURE BELOW 700°F (371°C).
Attempts to achieve heat output rates that exceed design
specifications can result in steel distortion and damage.
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030
$10.00
INSTALLATION AND
ADD MANUAL TITLE
OPERATION MANUAL
PARTICULATE EMISSIONS STANDARDS USING CORD WOOD. THIS APPLIANCE HAS BEEN
CSA / OMNI
/ INTERTEK
LOGO
Phone 1 (866) 820-8686 • https://ambiancefi replaces.com
(MUST use title from Price Book)
ADD PRODUCT IMAGE
U.S. ENVIRONMENTAL PROTECTION AGENCY (E.P.A.) CERTIFIED TO COMPLY WITH 2020
ADD SAFETY STANDARD INFORMATION
& EPA QUALIFICATION (IF APPLICABLE)
TESTED BY POLYTESTS AND LISTED BY CSA GROUP TO STANDARDS:
AS REFERENCED INTO 40 CFR PART 60 SUBPART AAA.
IF INSTALLATION + OPERATION, ADD SERIAL
IF SEPARATE MANUALS, ADD "PLACE
BARCODE LABEL ON THE OWNER'S MANUAL"
ENGLISH
Product Name / Code
Outlander-19
(AMB9010 leg model illustrated)
ADD ____ ILLUSTRATED
FOR INDOOR USE ONLY
ULC S627 AND UL 1482. METHODS ALT-125
REFERENCE #: 161746
NUMBER LABEL HERE
W415-2895 / C / 01.18.22

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Outlander-19 and is the answer not in the manual?

Questions and answers

Summary of Contents for Ambiance Fireplaces Outlander-19

  • Page 1 INSTALLATION AND ADD MANUAL TITLE OPERATION MANUAL Product Name / Code Outlander-19 INSTALLER: (MUST use title from Price Book) Leave this manual with the appliance. (AMB9010 leg model illustrated)
  • Page 2 safety information WARNING • This appliance is hot when operated and can cause WARNING severe burns if contacted. • Any changes or alterations to this appliance or its controls can be dangerous and is prohibited. HOT GLASS WILL • Do not operate appliance before reading and CAUSE BURNS.
  • Page 3 safety information WARNING • Your appliance requires periodic maintenance and cleaning. Failure to maintain your appliance may lead to smoke spillage in your home. • Ashes must be disposed in a metal container with a tight lid and placed on a non-combustible surface well away from the home or structure until completely cool.
  • Page 4: Table Of Contents

    table of contents general information operation dimensions optimum burn method specifi cations optional fan operation general instructions air control general information fi re extinguishers / smoke & carbon rating plate information monoxide detectors fuel installation planning lighting a fi re appliance placement 6.6.1 fl...
  • Page 5: General Information

    dimensions 1.0 general information dimensions W415-2895 / C / 01.18.22...
  • Page 6: Specifi Cations

    general information specifi cations * As tested using test method ALT-125. Specifi cations Emissions 2.25 grams / hour ** Figures will vary considerably with individual conditions. Overall Effi ciency 72.10% 77.54% 72.06% *** Wolf Steel Ltd. estimated realistic BTU/hr with hardwood logs and regular Height pedestal model 31 1/2"...
  • Page 7: General Information

    general information general information WARNING • Do not operate this appliance without the legs or pedestal installed. This appliance was specifi cally designed over many months of research to meet the 2020 U.S.A. EPA particulate emission standards and has been extensively tested in Canadian laboratories. This sytem is the most effi cient, simple and trouble-free we know and works as follows: AIR INLET PATH Secondary air from the rear hole travels up the back in the...
  • Page 8: Rating Plate Information

    general information rating plate information This illustration is for reference only. Refer to LISTED SOLID FUEL BURNING SPACE HEATER / the rating plate on the appliance for accurate POÊLE À COMBUSTIBLE SOLIDE HOMOLOGUÉ. TESTED TO: / TESTÉ SELON: UL1482 - 2011 / ULC S627 - 00 REFERENCE #: 161746 information MODEL / MODÈLE:...
  • Page 9: Installation Planning

    installation planning 2.0 installation planning appliance placement We recommend having your Ambiance wood burning appliance installed by a qualifi ed technician. However, should you choose to install the appliance yourself, it is extremely important that you follow all installation instructions for the appliance, the chimney and connector if applicable, as well as local building codes. At the very least, draw a detailed plan of your installation, including clearance dimensions to combustibles, and have your authorized dealer review them to confi...
  • Page 10: Alcove Installation

    installation planning alcove installation Your appliance may be installed using a listed double wall connector, such as Security DL6 in 19" 48” (122cm) (48.3cm) Canada, the Simpson Duravent Plus DVL in the USA or an equivalent double wall connector, into an alcove having a depth of no more than 4 "...
  • Page 11: Installation

    installation 3.0 installation WARNING • Wear gloves, protective footwear and safety glasses for protection. • Carefully follow the instructions for assembly of the pipe and other parts needed to install the appliance. Failure to do so may result in a fi re, especially if combustibles are too close to the appliance or chimney and air spacers are blocked, preventing the free movement of cooling air.
  • Page 12: Chimney

    installation chimney WARNING • Never install a single wall slip section or smoke pipe in a chase structure. The higher temperature of this single wall pipe may radiate suffi cient heat to combustible chase materials to cause a fi re. •...
  • Page 13: Chimney Connection

    installation 3.1.1 chimney connection Your chimney connector and chimney must have the same diameter as the appliance’s exhaust fl ue outlet. The appliance pipe must be made of aluminized or cold roll steel with a minimum 24 gauge (0.6mm) thickness. It is strictly forbidden to use galvanized steel.
  • Page 14: Adding Sections

    installation 3.1.2 adding sections Add chimney sections, according to the manufacturer’s installation instructions. If the chimney system passes through an attic space, a rafter radiation shield or attic insulation shield is required. The chimney must extend at least 3ft (0.9m) above its point of contact with the roof and at least 2ft (0.6m) higher than any wall, roof or building within 10ft (3.1m).
  • Page 15: Typical Through The Ceiling

    installation 3.1.3 typical through the ceiling Move the stove into position with the flue centered, midpoint between two joists to prevent having to cut them. Use a plumb bob to line up the center. Cut and frame an opening in the ceiling to provide a 2” (50.8mm) clearance between the outside of the chimney and any combustible material.
  • Page 16: Typical Through The Wall

    installation 3.1.4 typical through the wall If possible, design the installation so that the connector does not pass through a combustible wall. If during your installation you must pass through a combustible wall, check with your building inspector before you begin.
  • Page 17: Typical Existing Masonry

    installation 3.1.5 typical existing masonry You can also install your appliance using your existing masonry chimney. To do so, use the RAFTER following guidelines. Use a factory-built thimble, or construct your own brick thimble. If you are using a masonry chimney, it is important that it be built in EAVE compliance with the specifications of the Building CLEARANCE WITH FIRESTOP...
  • Page 18: Finishing

    fi nishing 4.0 fi nishing leg installation WARNING • Do not remove knockout unless installing the optional ash drawer kit. To avoid being damaged during shipping, the appliance has been bolted to the pallet and must be unbolted before the appliance can be installed. note: If installing the optional ash drawer, see “optional ash drawer kit (EP20LAD)”...
  • Page 19: Pedestal Installation

    fi nishing pedestal installation note: If an optional ash drawer kit is to be installed, ensure open side of pedestal is at the front of the appliance. If not, opening should be at the back. To avoid being damaged during shipping, the appliance has been bolted to the pallet and must be unbolted before the appliance can be installed.
  • Page 20: Door Handle Installation

    fi nishing door handle installation WARNING • Burning your appliance in with the doors open or ajar creates a fi re hazard that may result in a house and/or chimney fi re. • Do not strike or slam door. • Never remove the door when the appliance is hot.
  • Page 21: Secondary Air Tubes

    fi nishing secondary air tubes Start at the back working forwards by sliding the secondary air tube in the fi rebox and inserting the tube into the hole. Slide the tube into the opposite hole. With the holes on the secondary air tube pointing forward, align the tube with the tube retainer and insert the cotter pin.
  • Page 22: Brick And Baffl E Installation

    fi nishing brick and baffl e installation WARNING • Operation of the appliance without the baffl es can result in excessive temperatures that could damage the appliance, chimney and the surrounding enclosure. With the appliance and chimney installation completed, move the bricks into place as illustrated below (Fig. 4-5). Install nine (A) bricks and one (B) brick along the bottom of the fi...
  • Page 23: Ash Lip Installation

    fi nishing ash lip installation To avoid damage during transport, the ash lip has been shipped in the fi rebox. Using the two screws that secured the appliance to the shipping bracket, attach the ash lip as illustrated. W415-2895 / C / 01.18.22...
  • Page 24: Optional Installation

    optional installation 5.0 optional installation blower kit installation WARNING • Risk of fire and electrical shock! • Turn off the gas and electrical power before servicing this appliance. • Use only Wolf Steel approved optional accessories and replacement parts with this appliance. Using non-listed accessories (blowers, doors, louvres, trims, gas components, venting components, etc.) could result in a safety hazard and will void the warranty and certification.
  • Page 25: Leg Ash Drawer Kit (Ep20Lad)

    optional installation leg ash drawer kit (EP20LAD) WARNING • Failure to achieve a good seal between the ash opening and ash plug will result in an over-fi re condition that could cause damage to the appliance. Provisions have been made on the appliance to install an optional ash drawer kit. The kit allows for convenient removal of excess ash.
  • Page 26: Pedestal Ash Drawer Kit (Ep20Pad)

    optional installation pedestal ash drawer kit (EP20PAD) WARNING • Failure to achieve a good seal between the ash opening and ash plug will result in an over-fi re condition that could cause damage to the appliance. Provisions have been made on the appliance to install an optional ash drawer kit. The kit allows for convenient removal of excess ash.
  • Page 27: Operation

    operation 6.0 operation WARNING • Always operate this appliance with the door closed and latched except during startup and re-fueling. Always wear gloves to prevent injury. Do not leave the fi re unattended when the door is unlatched as unstable wood could fall out of the fi...
  • Page 28: Optimum Burn Method

    operation optimum burn method For optimal emissions performance and effi ciency follow these simple guidelines when using your appliance: Maintain a 2" (51mm) deep, hot, glowing red coal bed. Burn dry seasoned wood with less than 20% moisture content and burn so that the glass door remains clean.
  • Page 29: Fi Re Extinguishers / Smoke & Carbon Monoxide Detectors

    operation fi re extinguishers / smoke & carbon monoxide detectors note: Always check your smoke and CO detectors are working properly. All homes with a solid fuel burning appliance should have at least one fi re extinguisher in a central location, known to all, at least one smoke detector and carbon monoxide (CO) detector in the room containing the appliance.
  • Page 30: Extended Fi Re

    operation 6.6.2 extended fi re Load your larger pieces of wood so they are tightly packed, close enough to prevent the fl ames from penetrating it completely. After approximately 30 minutes, depending on the size of the load, close the draft control completely making sure that the fi...
  • Page 31: Maintenance

    maintenance 7.0 maintenance WARNING • Turn off the power before servicing the appliance. • Appliance may be hot, do not service until appliance has cooled. • Do not use abrasive cleaners. Check your chimney and chimney connector for creosote and soot buildup weekly until a safe frequency for cleaning is established.
  • Page 32: Creosote Formation And Removal

    maintenance creosote formation and removal When wood is burned slowly, it produces tar and other organic vapors, which combine with expelled moisture to form creosote. The creosote vapors condense in the relatively cooler chimney fl ue or a slow-burning fi re. As a result, creosote residue accumulates on the fl...
  • Page 33: Door Glass Replacement

    maintenance door glass replacement WARNING • Do not use substitute materials. • Glass may be hot. Do not touch glass until cooled. • Care must be taken when removing and disposing of any broken door glass or damaged components. Be sure to vacuum up any broken glass from inside appliance before operation.
  • Page 34: Wood

    maintenance wood WARNING • This appliance is designed to burn natural wood only. Do not burn treated wood, coal, charcoal, coloured paper, cardboard, solvents or garbage. This appliance has not been tested with an unvented gas log set. To reduce risk of fi re or injury, do not install an unvented gas log set into the appliance. •...
  • Page 35: Replacement Parts

    8.0 replacement parts WARNING • Failure to position the parts in accordance with this manual or failure to use only parts specifi cally approved with this appliance may result in property damage or personal injury. Contact your dealer for questions concerning prices and policies on replacement parts. Normally, all parts can be ordered through your Authorized dealer / distributor.
  • Page 36: Overview

    replacement parts W415-2895 / C / 01.18.22...
  • Page 37: Accessories

    accessories 9.0 accessories W415-2895 / C / 01.18.22...
  • Page 38: Troubleshooting

    10.0 troubleshooting WARNING • Turn off the appliance completely and let cool before servicing. Only a qualifi ed service person should service and repair this electric appliance. • Appliance may be hot, do not service until appliance has cooled. • Do not use abrasive cleaners.
  • Page 39: Warranty

    11.0 warranty AMBIANCE products are manufactured under the strict Standard of the World Recognized ISO 9001 : 2015 Quality Management System. AMBIANCE products are designed with superior components and materials, assembled by trained craftsmen who take great pride in their work. The complete appliance is thoroughly inspected by a qualifi ed and authorized installer, service agency or supplier before packaging to ensure that you, the customer, receives the quality product that you expect from AMBIANCE.
  • Page 40 WOLF STEEL LTD. 24 Napoleon Road, Barrie, Ontario, Canada L4M 0G8 103 Miller Drive, Crittenden, Kentucky, USA 41030 7200 Trans Canada Highway, Montreal, Quebec, Canada H4T 1A3 Tel: 1-866-820-8686...

This manual is also suitable for:

Amb9010

Table of Contents