Do you have a question about the ST-550 and is the answer not in the manual?
Questions and answers
Summary of Contents for Mueller ST-550
Page 1
S MART Bi det Toilet Model: ST-550 USER MANUAL Your satisfaction is guaranteed. If you are not completely satisfied with our Smart Bidet Toilet, and the results it brings, we insist that you let us know. We’ll help you make the Smart Bidet Toilet work for you, or we’ll refund your money.
TABLE OF CONTENTS IMPORTANT SAFEGUARDS..................2 PRODUCT OVERVIEW....................4 INSTALLING YOUR SMART BIDET TOILET..............6 • Tools Needed....................... 6 • Prior to Installation....................... 7 • Installing the Smart Bidet Toilet................... 7 • Installing the Remote Control Holder................9 • Installing and Replacing the Battery Box..............10 CONNECTING POWER &...
Improper installation and maintenance work or repairs can create substantial hazards to the user, for which Mueller cannot be held liable. • Turn off the power at the power breaker or disconnect the power plug from the outlet when cleaning.
Page 4
• The device must be disconnected from the power supply for any and all installation and maintenance work and for repairs. • Do not connect or disconnect the power plug with wet hands, as this may cause electric shock. • Do not use outdoors and do not operate in a space where aerosol spray is used or con- centrated oxygen is being administered.
PRODUCT OVERVIEW Seat Cover Dryer Side Control Panel Power cord Bidet Wash Nozzle (Back and Front Wash) Sensor Self-Heating Seat T-valve Ceramic Toilet Bowl Water Valve Kick Flush Ceramic Water Supply Hose Power/Stop Rear Front Flush...
Page 6
REMOTE CONTROLLER Front Washing Flushing Rear Washing Nozzle Position Water Pressure Adjust the nozzle Adjust the cleaning Position in five intensity of front levels and rear washing H/C Massage Cleaning with hot Flush and cold water Night Light Front Rear Turn the Night Light ON / OFF Dryer...
INSTALLING YOUR SMART BIDET TOILET TOOLS NEEDED: Please have these tools prepared prior to installation. Drill Marking Screw Measuring Silicone Crescent (Dia. 0.24in) driver tape wrench T-valve(1 pc) Two AAA Batteries • Please confirm that all the items from the Item list are inside of the package. If anything is missing, please contact our customer service at (888) 632-9981 •...
PRIOR TO INSTALLATION: - Please check that there is enough pre-arranged space for sewage, electric wires, and water lines. - Also, please confirm the distance from the toilet flange centerline to the wall. To confirm mentioned above, please refer to the diagram below: 15.86 26.93 20.67...
Page 9
2. Install the washer and bolts to the flange. 3. Place the flange onto the drain hole, and ensure the bolts are properly aligned with the centerline. Then mark the location of sec- tions 1, 2, 3, and 4, as illustrated. 4.
8. Attach the flush water hose to the T-valve 9. Attach the clean water hose to the T-valve and tighten. and tighten. 10. Connect the T-valve to the water supply and tighten. INSTALLING THE REMOTE CONTROL HOLDER: ATTENTION: The remote holder should be installed within a reach while seated on the unit.
INSTALLING AND REPLACING THE BATTERY BOX: Installation: 1. Remove the extension cable from the back of the toilet. The cable is attached inside the back of the toilet. Pull it gently to let it free. 2. Plug the cable into the battery box, and secure the water-proof nuts.
CONNECTING POWER & TESTING WATER FLOW AND THE UNIT TESTING WATER FLOW & CONNECTING POWER: 1. Open the water supply valve to its maximum, as shown in the figure below. Confirm that none of the connecting parts have a leak. NOTE: In case of water leaking, unfasten the nuts and reinstall them again.
PAIRING THE REMOTE CONTROL WITH THE UNIT: The remote control is paired with the unit before the unit is delivered to you. In the case of remote control malfunction, please proceed with the following steps: Hold the Stop button 1. Unplug the power cable from the wall Lights flicker outlet.
BATTERY ONLY MODE: To operate the unit during the power outage, or if the unit is unplugged from the wall outlet, press the Pow- er/Stop button to turn On, and press the Flush button. If the unit is not flushing properly, replace the battery with its spare, or contact us at (888) 632-9981 NOTE: Only the flush function is available in a battery-only mode.
• Eight safety layers: Eight different built-in safety features to protect the user and product. • Energy-efficient: The product will automatically power off 24 hours after the last use to save power. SPECIFICATIONS ST-550 0.14MPa 0.75MPa 7.09 2.56 0.79...
CLEANING & MAINTENANCE ATTENTION: Unplug the unit from the power outlet and shut the water supply before maintenance. ATTENTION: Direct water wash of the entire unit is strongly prohibited, as it would permanently damage the product and result in a fire. CLEANING THE TOILET BOWL: •...
TROUBLESHOOTING Should you run into any issues, please consult the troubleshooting guide below, or contact our Cus- tomer Support department at (888) 632-9981 The toilet is not working Bidet nozzle does not spray Weak water flow Spray is out of control Water is not warm Water leak Wash function does...
Page 18
Dryer not warm Seat temp. not warm Water temperature indicator light starts flashing blue Remote control failure Weak Flush Siphon jet at bottom of toilet does not work Toilet does not flush...
Page 19
Soft-close feature on seat/lid does not work Auto open/close lid/seat failure...
Page 20
Your purchase comes with a 100% satisfaction guarantee from Müeller If you are not happy with the product for any reason, please contact us at support@muellerdirect.com or 888-632-9981 with your feedback or questions, and we will do our best to make things right for you! Müeller USA 2720 Pellissier Place, Ste 73D...
Need help?
Do you have a question about the ST-550 and is the answer not in the manual?
Questions and answers