Haier 1U71SABFRA Service Manual page 71

500
140
Floor fixing dimensions
of the outdoor unit
(Unit:mm)
1U09BYFSRA 1U12BYFSRA
131 628
1U18RABFRA
1U53RABFRA
FOR 09K 12K
FOR 18K
FOR 24K
Indoor unit
1
Fitting of the Mounting Plate and Positioning of the wall Hole
When the mounting plate is rst xed
1. Carry out, based on the neighboring pillars or lintels, a
to be xed against the wall, then temporarily fasten the plate with one steel nail.
2. Make sure once more the proper level of the plate, by hanging a thread with a
weight from the central top of the plate, then fasten securely the plate with the
attachment steel nail.
3. Find the wall hole location A using a measuring tape
A=170mm
B= Ø 60mm
D=47mm
A=218mm
B= 60mm
Ø
D=38.5mm
2
140
114.2
Floor fixing dimensions
of the outdoor unit
(Unit:mm)
1U09JACFRA
1U12JACFRA
1U26JACFRA
1U35JACFRA
131
130
1U24SABFRA
1U71SABFRA
Selection of pipe
proper leveling for the plate
C=130mm
D=47mm
C=151mm
D=38.5mm
590
114.2
When the mounting plate is xed side bar and lintel
Fix to side bar and lintel a mounting bar, Which is separately sold, and then
fasten the plate to the xed mounting bar.
Refer to the previous article, " When the mounting plate is
position of wall hole.
2
Making a Hole on the Wall and Fitting the Piping Hole Cover
660
130
(Section of wall hole)
3
Installation of the Indoor Unit
[ Rear piping ]
[ Left ・
the mark of hole for left-rear piping which is marked on heat insulation materials.
1. Insert the drain hose into the dent of heat insulation materials of indoor unit.
2. Insert the indoor/outdoor electric cable from backside of indoor unit, and pull it
out on the front side, then connect them.
3. Coat the aring seal face with refrigerant oil and connect pipes.
Cover the connection part with heat insulation materials closely, and make sure
xing with adhesive tape
Lid for right
piping
Lid for under piping pipe
Fix with adhesive tape
piping by protecting tape.
[ Other direction piping ]
then bend the pipe according to theposition of wall hole. When bending, be
careful not to crash pipes.
connected to the heat insulation of connecting part specially.
B= 60mm
Ø
Hang surely the unit body onto the upper notches of the
mounting plate. Move the body from side to side to verify its
secure xing.
In order to x the body onto the mounting plate,hold up
the body aslant from the underside and then put it down
perpendicularly.
B= 60mm
Ø
When you unload the indoor unit,please use
your hand to arise the body to leave agraffe,
then lift the bottom of the body outward
slightly and lift the unit aslant until it
leaves the mounting plate.
Make a hole of 60 mm in diameter, slightly descending to outside the wall.
Install piping hole cover and seal it off with putty after installation
Wall hole
Ø60mm
Indoor side
Drawing of pipe
Draw pipes and the drain hose, then fasten them with the adhesive tape
Left-rear piping ]
In case of left side piping, cut away, with a nipper, the lid for left piping.
In case of left-rear piping, bend the pipes according to the piping direction to
Lid for left piping
Indoor/outdoor electric cable and drain hose must be bound with refrigerant
Cut away, with a nipper, the lid for piping according to the piping direction and
Connect beforehand the indoor/outdoor electric cable, and then pull out the
Fixing the indoor unit body
Unloading of indoor unit body
rst xed ", for the
Thickness of wall
Piping hole pipe
G
Outdoor side
Heat insulation
Piping
material
Pipe supporting
plate
Drain hose
Indoor/outdoor electric cable
mounting plate
mounting plate
agraffe