Table of Contents
Advertisement
U
6
5
SOLO
+15
63
+15
1
FX
U
U
6
61
SIG/OL
+15
FX
+15
FX MASTER
TO AUX 1
U
64
TAP
+15
DELAY
65
TO AUX 2
U
+15
MUTE
66
U
+15
U
LOW
80Hz
OFF
MAX
OFF
COMP
COMP
+15
R
MUTE
1
dB
dB
10
10
5
5
U
U
SOLO
5
5
10
10
20
20
30
30
40
40
50
50
60
60
O O
O O
65. Preset Selector, Tap Delay and LED
Rotate these endless controls to select one of the
24 preset effects. When the rotation stops, that preset
will be loaded and become operational. The current
preset number is shown in the display [64].
The different presets are shown in the table to the
right and on the silkscreen in the upper right hand
corner of each VLZ4 4•Bus mixer. Further details of
each preset are explained in Appendix E on page 37.
1
2
SOLO
SOLO
2
FX
U
U
U
SIG/OL
+15
+15
FX MASTER
TO AUX 1
U
U
62
TAP
+15
DELAY
TO AUX 2
U
U
MUTE
+15
TO LR
TO LR
SUBGROUPS
72
MAX
OFF
MAX
OFF
COMP
COMP
73
2
3
4
dB
dB
10
10
5
5
U
U
5
5
74
10
10
20
20
30
30
40
40
50
50
60
60
O O
O O
SOLO MODE
PFL
AFL
1
U
2
67
3
+15
+15
SOLO
4
U
5
68
6
+15
+15
MONITOR
7
U
8
69
9
+15
+15
PHONES
10
TALKBACK
U
11
70
12
MAX
+15
LEVEL
The knob also offers a tap delay function for presets
17-24. This works as follows:
PUSH
TO TALK
1. Use the knob to select a preset from 17 to 24.
71
AUX 1-4
2. Press the knob in at least two times.
MAIN
MAIN MIX
dB
10
5
U
5
75
10
20
30
40
50
60
3. The LED will flash in time with the new tap
O O
66. Internal FX Mute
When engaged, the internal effects processor is
muted, and its output will not appear on the main mix,
monitor mix...or anywhere for that matter. The adjacent
mute LED will come on as a reminder that the effects
are muted. When power is first applied, these LEDs will
illuminate and the FX will be muted for about 10
seconds while the little FX gerbils inside settle down.
If this switch is not engaged, then the internal effects
are set free and may be added as required to the main
mix, monitor mix and last two stereo channels.
67. Solo Level
This knob is used to adjust the volume of the soloed
signal as it is routed to the monitor [15, 16] and phones
[17] outputs. This control is independent of, and prior
to, the monitor [68] and phones [69] level controls.
Plate Reverb
13
Vocal Plate
14
Warm Room
15
Bright Room
16
Warm Lounge
17
Small Stage
18
Warm Theater
19
Bright Stage
20
Warm Hall
21
Concert Hall
22
Cathedral
23
Gated Reverb
24
The DSP processor will calculate the time delay
between the last two pushes, and it will assign
this time interval to the echoes of the current
digital delay.
The minimum tap delay is 50 ms and the
maximum is 500 ms.
•
If your taps are faster than 50 ms, they will
be set to 50 ms.
•
If taps are 500 ms to 1 second, they will be
set to 500 ms.
•
If taps are greater than 1 second apart,
they will be ignored. Try again a bit faster.
delay time.
Chorus
Chorus + Reverb
Doubler
Tape Slap
Delay 1 Brt 350ms
Delay 1 Wrm 300ms
Delay 2 Brt 250ms
Delay 2 Wrm 200ms
Delay 3 Brt 175ms
Delay 3 Wrm 150ms
Chorus + Dly 300ms
Reverb + Dly 200ms
Owner's Manual
25
Advertisement
Table of Contents
