Subscribe to Our Youtube Channel
Summary of Contents for Joyside JS-OH-Z03 Series
- Page 1 INSTRUCTION MANUAL Joyside Standing Heater Series JS-OH-Z03 IF YOU PURCHASED THE GREENHOUSE ONLINE AND HAVE ANY QUESTION OR CONCERNS PLEASE CONTACT US WITH EMAIL OR WHATS APP service@joysidefurniture.com. WhatsApp QR Code...
- Page 2 Model No：JS-OH-Z03A， JS-OH-Z03B Model No.：PH02-S/CAPH-7SMOCHA/CAPH-7-S /CAPH-7-SB/ CAPH-7-S HB /v-CAPH-7-S/PH02-SS/CAPH-7-SS DANGER If you smell gas: 1. Shut off gas to the appliance. 3. If odor continues, keep away from the appliance and immediately call WARNING Do not store or use gasoline or other vicinity of this or any other appliance.
-
Page 3: Safety Information
SAFETY INFORMATION Before you assemble or operate this unit, please carefully read this entire manual. Failure to do so WARNING The installation of this unit must adhere to local codes or either the National Fuel Gas Code, ANSI Z223. 1/NFPA54, OR CAN/CGA-B149.1, National Gas and Propane Installation Code. THIS UNIT IS INTENDED FOR OUTDOOR USE ONLY! This product shall be used outdoors, in a ventilated space and shall not be used in any enclosed area. - Page 4 damaged parts should this occur. • Do not disconnect any part while unit is in use. • Do not store a spare propane tank on or near this unit. • If the heating unit is indoors, detach the propane tank and leave outdoors. •...
- Page 5 SAFETY INFORMATION BE CAREFUL: WHEN CERTAIN MATERIALS OR ITEMS ARE STORED ABOVE, BESIDE OR UNDER THIS HEATER WHILE IN USE, THEY WILL BE SUBJECT TO RADIANT HEAT AND COULD BE SERIOUSLY DAMAGED. Combustible materials should not be within 24 inches of the top of the unit, or within 36 inches around the entire unit.
- Page 6 HARDWARE Item Description M6x10 Screw M6 Nut M8 Bolt M6x22Bolt Wrench Re ector Stud Wing Nut Washer Anchoring Arm Anchoring Nut Cap Nut Small screw Webbing Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list.
- Page 7 CONTENTS Item Description Re ector Panel Center Re ector Head Assembly Post Tank H ousing Post S upport Support L egs Regulator Base Wheel A ssembly Page 6...
- Page 8 ASSEMBLY INSTRUCTIONS 1. Align the holes in the wheel assembly (J) with the holes in the base (I), attach the wheel assembly to the base using 2 pcs M6x10 screws (AA) and 2 pcs M6 nuts (BB). 2. Mount the 3 pcs anchoring arms (II) to the holes on the base (I) using 6 pcs M6x10 screws (AA) and 6 pcs M6 nuts (BB).
- Page 9 ASSEMBLY INSTRUCTIONS 4. Attach the post support (F) to the top of the support legs (G) using 6 pcs M6 x 22 bolts (DD) and 6 pcs M6 nuts (BB). 5. Place the tank housing (E) on top of the assembly. (FF) into the top holes of the head assembly (C).
- Page 10 WARNING e e e s m m m b b b n n n i i i l l l ! ! ! g g g semble the outer rim using one small screw (LL) and one cap nut (KK). Repeat this step with the three M6 screws (AA) and three cap nuts (KK).
- Page 11 ASSEMBLY INSTRUCTIONS 10. Remove the pre-assembled screws from the post support (F) and attach post (D) to the post support (F) using those 4 screws. 11. Place the 20 lb gas cylinder in the center of the base, fasten it with the webbing (MM). 12.
-
Page 12: Operation
OPERATION Before performing a leak test, be sure that no sparks can occur and you are in a spacious outdoor area. Connect the propane gas tank to the regulator and turn the valve on the unit to the “off” position. Brush a soap and water mixture on all connections. Turn the gas supply on; if bubbles occur on any connection there may be a leak. -
Page 13: Maintenance
MAINTENANCE Before performing any maintenance always disconnect propane gas tank. Keep the heating item free and clear from combustible materials. Visually inspect burner for obstructions and keep tank enclosure free and clear from debris. Use a soft brush to get rid of the mild stains, loose dirt and soil after the burner is completely cooled down. -
Page 14: Troubleshooting
TROUBLESHOOTING Problem Cause Solution The burner will not light. The burner injector is clogged. Clean the burner injector. There is low gas supply pressure. Call your gas supplier. The burner flame goes off There is low gas pressure. Call your gas supplier. immediately after ignition. -
Page 15: Warranty
WARRANTY PRODUCT WARRANTY LENGTH : 3 MONTHS WARRANTY DETAILS :INSISTS ON THE HIGHEST ATANDARD OF QUALITY IN MANUFACTURING. IN CASE OF ANY ISSUES DO NOT RETURN. Page 14...
Need help?
Do you have a question about the JS-OH-Z03 Series and is the answer not in the manual?
Questions and answers