Advertisement
ASSEMBLING YOUR VERSAHAUL
Step 1
5
/
" Carriage Bolt
16
Insert the Tie-Down
Loops into the Main
Main Rail
Rail and fasten them
with the
/
" x
/
"
5
3
16
4
Tie-Down Loop
Carriage Bolts, Flat
Washers, Lock
5
/
" Flat Washer
16
1.1
Washers, and Nuts in
5
/
" Nut
16
that order (Figure 1.1). Insert the Loops from the inside of the rail. The circled area is where
the ramps will be installed (Figure 1.2). These instructions are described in detail later.
Step 2
Insert the Main Tube into the Main Rails. Make sure the
main rail with tail-light mount holes and license plate
holes is to the rear when attached to the vehicle. Slide
the Main Rails to desired spacing and lock tight with the
Main Tube
3
/
8
3
/
" Bolts
8
Main Rail
Step 3
5
/
" Bolt
16
Insert the Wheel Stop into the slots on the top of the
Wheel Stop
Main Rail at the appropriate position and fasten with
Bolt, Flat Washer, Lock Washer, and Nut.
5
/
" Flat Washer
16
Main Rail
5
/
" Nut
16
Main Tube
Lock Pin
Lock Pin
Main Rail
Main Rail
Step 5
To attach the assembled Versahaul to your vehicle, first slide
Main Tube
the mounting bracket of the Main Tube onto the bumper.
Once in place, use the
Mounting Bracket
Bumper
1
/
" x 4" bolts to secure the carrier in place on the vehicle.
2
1
/
" Bolts
2
7
/
" Washers
16
1
/
" Nuts
2
For more information on your VersaHaul, please visit www.versahaul.com
Main Rail
1.2
" x 1
1
/
" Bolts.
4
Step 4
As a safety precaution, install the two square Lock
Pins through the main tube. Close and lock them
to ensure the main rails will not come loose.
/
" Washers with the
7
16
Ramp Top
1
/
" Lock Nut
2
1
/
" Nut
2
1
/
" Bolt
2
5
/
/
"
5
16
Tie-Down Loop
5
/
" Bolts
16
Ramp
Cotter Pin
Main Rail
/
" Nuts, and
1
2
Tie-Down Loop
military issue motorcycle carrier
VH-MI INSTRUCTION DIAGRAM
Step 1
Attach each Spring Bracket to each VH-MI Ramp
Top part using the
1
/
" Bolt
4
1
/
" Nut
4
Step 2
Attach the VH-MI Ramp Top part to the VH-MI Ramp
Bottom part by screwing the
Ramp Top
Nut, followed by the
Ramp Bottom
Step 3
Attach each of the Hinge Brackets to one end of
5
/
" Nuts
16
the VH-MI Carrier Rails using all of the
" Lock Washers
16
Bolts,
/
5
16
assembled Tie-Down Loops on that end of the
rail will need to be removed before assembling
the Hinge Bracket.
holding the Tie-Down Loops will now be
Main Rail
Hinge Bracket
rescrewed to hold the Hinge Bracket as well.
5
/
" Carriage Bolts
16
Step 4
Attach the VH-MI Ramps to the VH-MI Carrier Rails by
using the Hinge Pins. Lock the Hinge Pins using the
Hinge Pin
Cotter Pins.
Step 5
Position the assembled VH-MI as shown and attach the
Springs onto the Tie-Down Loops on the Hinge Bracket
and the outer holes on the Spring Brackets. Once the
Springs are attached, pull Ramps upwards to the store
Spring
position and your VH-MI carrier is ready to be used.
Spring Bracket
Ramp
Problems? Questions? Call us at (888) 818-9915
ATTACHING THE RAMPS
/
" Bolts and Nuts.
1
4
/
" x 1
/
" Bolt with the
/
"
1
1
1
2
2
2
/
" Lock Nut.
1
2
5
/
"
16
" Lock Washers, and
/
" Nuts. The pre-
5
16
/
" Carriage Bolts previously
5
16
Advertisement
