Advertisement
Quick Links
EDUIWB & DIWB
Mobile Interactive White Board
060-0952 - Qty 1
Lifting Handle Assembly
060-0926 - Qty 1
Dual Arm Assembly
Owners
Guide
031-9454 - Qty 1
Owners Guide
Assembly Instructions
022-3312
Qty 1
Projector
Mount
Support
010-6127 - Qty 1
Cable Retention Bracket
017-1232
Qty 1
Guide Tube
030-1546 - Qty 1
300N Gas Spring
022-3331 - Qty 1
Projector Slide Assembly
010-6228 - Qty 2
Outer Bracket
030-1545 - Qty 1
White Board
060-0961 - Qty 2
Mounting Bar Assembly
010-6227 - Qty 1
Laptop Tray
1 of 25
Advertisement
Related Manuals for Bretford EDUIWB
Summary of Contents for Bretford EDUIWB
- Page 1 EDUIWB & DIWB Mobile Interactive White Board Assembly Instructions 017-1232 022-3312 Qty 1 Qty 1 030-1545 - Qty 1 Guide Tube Projector White Board Mount Support 030-1546 - Qty 1 300N Gas Spring 060-0961 - Qty 2 Mounting Bar Assembly...
- Page 2 030-0207 - Qty 15 030-0240 - Qty 2 030-0538 - Qty 13 1/4-20 Hex Nut 1/4” Lockwasher 1/4-20 x 1 1/4” Carriage Bolt 015-0176 - Qty 4 4” Stem Caster w/Brake 030-1026 - Qty 2 1/4-20 x 3/4” Phillips Screw 012-0696 - Qty 2 030-0962 - Qty 2 1”...
- Page 3 015-0176 022-3188 LOCK LOCK LOCK 3 of 25...
- Page 4 022-3187 Faces shorter side Correct Position 030-0538 030-0538 030-0207 030-0207 4 of 25...
- Page 5 030-1546 030-0538 030-0207 030-0538 030-0207 5 of 25...
- Page 6 022-3312 Correct Position 6 of 25...
- Page 7 030-0538 030-0207 030-0207 030-0538 7 of 25...
- Page 8 022-3182 030-0291 030-0291 8 of 25...
- Page 9 Follow this step ONLY if you are using an Espon Ultra Short Throw projector. If you are not, SKIP this step. You need to attach this bracket (#010-6662) to your projector. NOTE: This bracket may not fit on some older versions of the Espon projector. If this bracket does not fit on your projector, do not use it.
- Page 10 060-0961 030-0845 or 030-1234 Screw depends on the length you need with your porjector. 030-1397 030-1398 May not be necessary with your projector THIS PROJECTOR IS JUST AN EXAMPLE, YOUR PROJECTOR MAYBE INSTALLED IN DIFFERENT LOCATIONS IN THE SLOTS DUE TO THE MOUNTING Install mounting bar assembly to your projector.
- Page 11 017-1232 022-3331 Projector removed for clarity INSTALLING THIS ASSEMBLY REQUIRES 2 PEOPLE!! 11 of 25...
- Page 12 Projector removed for clarity 030-0538 030-0538 Flange sits on top of tube 030-0207 030-0207 12 of 25...
- Page 13 Board 030-1545 Position in rail 13 of 25...
- Page 14 BOARD MUST BE CENTERED Front View Back View 010-6120 030-0962 030-0962 14 of 25...
- Page 15 Note: Can be mounted to either side of cart. Best to mount on the same side cables plug into your projector. 060-0926 030-1026 030-0207 030-1026 030-0207 15 of 25...
- Page 16 030-0845 These are the main tension screws. They control the pitch movement of the vesa joint. Adjust carefully. 030-1267 16 of 25...
- Page 17 010-6228 012-0692 030-1571 17 of 25...
- Page 18 030-1569 (2)x 030-1621 (2)x 18 of 25...
- Page 19 NOTE: Before attaching the square foam pieces, decide where you are going to mount the outer brackets. Then proceed with attaching the foam squares. 030-1571 (2)x 012-0696 030-0272 030-0240 19 of 25...
- Page 20 When attaching the cable to the cylinder, be very careful not to pull up on the lever. By doing this it may cause the cylinder to spring up. 030-1611 - Cable QTY 1 Slide in place. Hook end of cable onto cylinder 20 of 25...
- Page 21 010-6127 21 of 25...
- Page 22 Slide cable through hole in handle assembly. 22 of 25...
- Page 23 Slide cable through eye lit hole and slide it to the left. 23 of 25...
- Page 24 With pliers, pull the cable through the next handle piece so that it sits in the narrow part of the eyelit hole. 24 of 25...
- Page 25 Bretford® Bretford Ltd. 11000 Seymour Avenue 2 Etongate Franklin Park, IL 60131 110 Windsor Road, Slough TEL: 847.678.2545 Berkshire SL1 2JA England 800.521.9614 TEL: 011 44 17 5353 9955 FAX: 847.678.0852 FAX: 011 44 17 5353 9478 800.343.1779 Part # 031-9504 25 of 25 www.bretford.com...
Need help?
Do you have a question about the EDUIWB and is the answer not in the manual?
Questions and answers